Daktronics SPORTSOUND SSN-250 Installation Manual page 27

BH
COMPONENT IDENTIFICATION LEGEND
ID TAG COMPONENT DESCRIPTION
SC 1 SPEAKER CLUSTER, SSN-250
AR 1 AMPLIFIER RACK, SSN-250
JB 1 SINGLE GANG XLR PLATE, J-BOX BY OTHERS.
JB 2 SINGLE GANG XLR PLATE, J-BOX BY OTHERS.
JB 3 JUNCTION BOX; SPEAKER CABLE
*AR1 MAY INCLUDE CONTROL EQUIPMENT (SSR-WR), OR IT MAY BE AMPLIFIER ONLY (0A-1756-0064)
AR 1
AMPLIFIER
RACK LOCATION INPUT 1
INPUT 2
· TYPICALLY LOCATED IN EQUIP. CLOSET.
· USE DEDICATED CIRCUIT.
· POWER CORD INSIDE OF ENCLOSURE.
CIRCUIT 1
TOTAL POWER REQUIREMENTS:
SYSTEM VOLTAGE
120 2 WIRES + GND
NUMBER OF POLES 1
MAXIMUM WATTS 1300W
AMPERES PER LINE 10.8
MANUFACTURER'S COMPONENT COMPONENT
PART NUMBER PROVIDED BY INSTALLED BY
NA DAKTRONICS INSTALL SUB
0A-1756-0064 DAKTRONICS INSTALL SUB
EC-1244 DAKTRONICS INSTALL SUB
EC-1244 DAKTRONICS INSTALL SUB
A-3551392 DAKTRONICS INSTALL SUB
SEE SYSTEM
SCHEMATIC FOR
ADDITIONAL WIRING
DETAILS: DWG-03822601
B
A
JB 2
SECONDARY AUDIO
A
CONTROL LOCATION
(OPTIONAL)
SIGNAL DISTRIBUTION SYSTEM LEGEND
DAKTRONICS
ID TAG CABLE TYPE SIZE (O.D.)
PART NUMBER
A AUDIO; 1 PAIR, 22 AWG 0.17" W-1615
B 4 PAIR, 13 AWG SPEAKER WIRE 0.58" W-3371462
C 1 PAIR, 12 AWG SPEAKER WIRE 0.279" W-1561
· INSTALLATION SUBCONTRACTOR MAY BE HIRED THROUGH DAKTRONICS OR CUSTOMER. REFER TO PROJECTS IR CHECKLIST FOR
FURTHER CLARIFICATION OF INSTALLATION RESPONSIBILITIES.
SC 1
SPEAKER
CLUSTER
LOCATION
C @7
SPEAKER JUNCTION
BOX MOUNTS TO
JB 3
CEILING STRUCTURE
NEAR SPEAKER
CLUSTER LOCATION
JB 1
PRIMARY AUDIO
CONTROL LOCATION
CONDUIT PROVIDED CABLE
& INSTALLED BY PROVIDED BY INSTALLED BY
INSTALL SUB DAKTRONICS INSTALL SUB
INSTALL SUB DAKTRONICS INSTALL SUB
NA DAKTRONICS DAKTRONICS
UPDATED DRAWING NUMBERS TO CORRESPOND
REV DATE:
WITH AMPLIFIER CHANGE
01 4 APR 18
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY
ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF
DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.
DAKTRONICS AUDIO SYSTEMS
PROJECT:
RISER; SSN-250; POWER AND SIGNAL LAYOUT
TITLE:
25 JAN 17
DATE:
NTS
SCALE:
DTREML
DESIGN:
DTREML
DRAWN:
TERMINATED BY
DAKTRONICS
DAKTRONICS
DAKTRONICS
ELECTRICAL NOTES:
THIS DRAWING IS NOT SCALED AND SHOULD BE
USED FOR POWER AND SIGNAL REQUIREMENTS
ONLY.
IT IS THE RESPONSIBILITY OF THE INSTALLER TO
ENSURE THAT ALL ELECTRICAL WORK PERFORMED
ON SITE MEETS OR EXCEEDS ALL LOCAL AND
NATIONAL ELECTRICAL CODES.
ALL SIGNAL CABLE RUNS SHOULD BE LABELED WITH
THEIR ORIGIN AND DESTINATION ON EACH END.
DAKTRONICS IS NOT RESPONSIBLE FOR THE
QUALITY OF THE POWER DELIVERY SYSTEM TO THE
AMPLIFIER RACK.
BECAUSE EACH INSTALLATION IS UNIQUE,
DAKTRONICS OFFERS THESE INSTRUCTIONS AS
GUIDELINES ONLY. DAKTRONICS, INC. ASSUMES NO
LIABILITY IF INSTALLATION STEPS HAVE BEEN
OMITTED OR OTHER NECESSARY PROCEDURES ARE
NOT INCLUDED IN THIS SYSTEM RISER DIAGRAM.
POWER AND SIGNAL REQUIREMENTS ARE
SPECIFIED TO THE EQUIPMENT AND SETUP SHOWN.
ANY CHANGES MADE TO EQUIPMENT OR THEIR
SETUP SHOULD BE DISCUSSED WITH DAKTRONICS
DESIGN PERSONNEL.
THE CONTRACTUAL AGREEMENT WILL DETERMINE
THE PARTY OR PARTIES RESPONSIBLE FOR ITEMS
FIELD INSTALLED. THIS DRAWING IS NOT INTENDED
TO DETERMINE RESPONSIBILITIES AND SHOULD BE
USED FOR REFERENCE ONLY.
ACTUAL PLACEMENT OF THE AMPLIFIER RACK,
JUNCTION BOXES, AND SPEAKER CLUSTER MAY
VARY. LOCATION OF SUCH EQUIPMENT TO BE FIELD
VERIFIED.
BY:
CJB
THIRD ANGLE PROJECTION
COPYRIGHT 2017 DAKTRONICS, INC. (USA)
INCHES [MILLIMETERS]
DIM UNITS: SHEET REV
DO NOT SCALE DRAWING 01
3554927
JOB NO. FUNC - TYPE - SIZE
P1756 R 03 B
- -