Troubleshooting - Tecomec Jolly Star Owner's Manual

28. grIndIng wHeel dreSSIng for SHarPenIng THe dePTH
gauge
- Fit the 6-mm thick grinding wheel (fig.37), following the instructions given in points
13-17-18-19.
- Turn the vise so that the "0" reference mark is on position 0 (fig.38).
- Turn the arm to take the "0" reference mark to 10°/15° (fig.38).
- Position the dressing brick on the jaws and against the chain blocking unit
(fig.38).
Hold the dressing brick firmly with one hand (being careful not to touch the
grinding wheel).
- Profile the grinding wheel by activating the machine and grind the grinding wheel
until you obtain a profile like the one illustrated in fig.38.
- Switch the machine off once you have finished.
29. SHarPenIng THe dePTH gauge
- Remove the dressing brick and put the chain in the vise.
- Center the cutter compared to the grinding wheel by turning the knobs (P29 and
P30).
- Keeping the arm tilted, adjust the grinding depth on the gauge by turning knob P31
(fig.39).
- Sharpen the gauge following the instructions given in the "SHARPENING" section.
For this type of sharpening procedure, there is no difference between the right and
left cutters, therefore sharpen all the gauges one after the other.
- Check if the gauge depth is correct, using the template with the shape related to
the type of chain used (fig.40). Please also consult the chain table, column F.
30. SToPPIng and SHuTTIng down
30.1 SToPPIng
Turn the machine off by turning the switch to position "0" and unplug the power cable
from the mains.
30.2 SHuTTIng down
Once you have finished using the machine, disconnect it and clean it thoroughly.
Store it in a dry and safe place, protected against dust and damp.
30.3 rouTIne maInTenance
Follow the instructions given in the "STOPPING" section before you start to
work on the machine.
maintenance frequency
When the grinding wheel reaches a
minimum diameter of approximately
105 mm
40 hours
30.4 HandlIng and TranSPorT
- If you need to transport the machine, take it off the bench or wall, dismantle the grind-
ing wheel and put all the parts in a packing box to protect them against impact.
30.5 demolITIon and dISPoSal
The machine is to be demolished by qualified personnel in compliance with current
laws in force in the country in which it is installed.
The symbol (on the rating nameplate) points out that the product must not be
disposed of with normal household garbage. Contact an authorized tip or your dealer
for disposal instructions.
Before you scrap the machine, make it unusable by cutting the power supply
cable for example and make the parts safe, which could cause a source of
danger for children if they should play with the machine.
8
P00801026_R04_U&M_JollyStar_230.indd 8
operation
Replace the grinding wheel.
Clean the lamp carefully using a rag or a
cleaning brush.
Do not use compressed air.
Clean the grinder carefully using a rag or
a cleaning brush.
Clean the electric motor and the sliding
guides with caution.
Do not use compressed air.
en
31. Trouble SHooTIng
Follow the instructions given in the "STOPPING" section before you start to
work on the machine.
Problem
One of the safety devices
of the system to which
the machine is connected
The machine fails to
has tripped (fuse, circuit
start when you switch on
breaker etc.)
(switch in pos. "1").
The machine is not plugged
into the mains properly.
The lamp is not screwed
The lamp fails to switch on
properly into its seat.
when the switch is turned
to position "1".
The lamp has blown.
The grinder is not secured
correctly.
The arm-motor unit is not
secured correctly to the
base unit.
The machine vibrates
abnormally.
The vise assembly is not
secured correctly to the
base unit.
The grinding wheel is not
fitted correctly in its seat
on the hub.
- Contact a skilled technician if you are still unable to restore the correct operation
of the machine following the instructions given in the chart.
Probable cause Solution
Reset the safety device.
If the safety switch trips
again, do not use the
machine, but contact a
Skilled technician.
Unplug and plug in again
properly.
Screw the lamp in place
properly.
Replace the lamp.
Check its attachment and,
if necessary, tighten the
securing screws correctly.
Tighten the related blocking
handle correctly.
Tighten the related blocking
handle correctly.
Dismantle the grinding
wheel, check its integrity
and fit again correctly.
29/01/2009 11.41.28