Connecting The Hose To The Appliance - Barbecook VICTOR 223.7020.000 User Manual

Cylinder, hose and
Country
regulator
DK, GR, NO, SE, EE,
Propane, 30 mbar /
LT, LV, CZ, PL, MT,
Butane, 30 mbar
HU, SI, SK, NL
ES, GB,, IE, PT, BE, Propane, 37 mbar /
FR, LU, IT, CY Butane, 28-30 mbar
This barbecue has been adjusted to be operate with 4,5
to 15 kg butane/propane cylinders with an appropriate
low pressure regulator. We recommend connecting the
appliance to propane. Propane offers a high-quality
combustion and is less sensitive to frost. The height H of
the cylinder must be less than 70 cm, regardless of the
cylinder's width or diameter D.
Buy your pressure regulator and gas cylinder together.
Not all regulators fit all cylinders.
Use only a gas hose and regulator that is homologated
for the country of use.
4.2 Safety instructions
• Never connect the cylinder directly to the appliance. Always
mount a pressure regulator on the cylinder first.
• Never modify pre-assembled or sealed parts of the cylinder,
the hose or the pressure regulator.
• Keep the hose as short as possible (1,5 m maximum) to
prevent it from dragging on the ground.
• Never distort or twist the hose. Do not pull or pierce
the hose.Keep the hose away from any parts of the
barbecue that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
• It should be replaced if it is damaged or cracked, when
required by national regulations or at the end of the part
lifecycle (f.ex France)
• Never open the gas supply.
• Always keep the cylinder in an upright position.
• Check for leaks each time you make changes to the gas
connection. See "5 Checking for gas leaks".
4.3

Connecting the hose to the appliance

France:
The equipment may be used with two types of flexible hose:
• Flexible hose designed to be joined onto ringed tailpieces
on both the barbecue and regulator sides, held firm
with collars (in accordance with standard XP D 36-110).
recommended length 1.25 m.
• Flexible hose (according to standard XP D 36-112) fitted
with a G 1/2 threaded nut for fixing to the barbecue
and a M 20x1.5 threaded nut for fixing to the regulator,
recommended length 1.25 m.
Other countries:
It should be used with flexible hose that is suitable for use with
butane and propane gas. Hose length should not exceed 1.50 m.
To connect the gas hose to the appliance, you have to mount
a coupling on the gas tube of the appliance. The appliance
comes with two couplings, both intended for particular
countries:
BE, CH, CZ, DK, ES,
223.7420.100
FI, GB, IE, IT, PT, SI
223.7420.000
Country Coupling
Coupling A
FR Coupling B
FR
If your country is not in the table, use the coupling that
complies with your national standards.
4.3.1 C
You need a 19 mm spanner and a cross-slotted screwdriver.
1. Screw the coupling on the gas tube of the appliance (A) and
tighten it with a 19 mm spanner (B).
2. Slide the hose over the coupling (C) and tighten the
clamping ring with a cross-slotted screwdriver (D).
4.3.2 C
You need a 22 mm spanner and an adjustable spanner.
1. Screw the coupling on the gas tube of the appliance (A) and
tighten it with a 22 mm spanner (B).
2. Screw the gas hose on the coupling (C) and tighten it with
two spanners. Hold the coupling with a 22 mm spanner,
while turning the hose with an adjustable spanner (D).
/
www.barbecook.com
A
oupling
B
oupling
5