Download
Share
Print this page
  1. Manuals
  2. Brands
  3. GAGEMAKER Manuals
  4. Measuring Instruments
  5. MIC TRAC MT-3000
  6. Manual

GAGEMAKER MIC TRAC MT-3000 Manual

Tf-vb bore gage fixture cal-pak fixture
Hide thumbs Also See for MIC TRAC MT-3000:

Advertisement

Quick Links

Download this manual
M
I
C
T
R
M
I
C
T
R
T
F
-
V
B
T
F
-
V
B
C
A
L
-
P
A
C
A
L
-
P
A
A
C
M
T
-
A
C
M
T
B
o
r
e
G
B
o
r
e
G
K
F
I
X
T
U
K
F
I
X
T
U
3
0
0
0
-
3
0
0
0
a
g
e
F
a
g
e
R
E
M
A
R
E
M
A
i
x
t
u
r
F
i
x
t
u
r
N
U
A
L
N
U
A
L
e
e

Advertisement

loading

Related Manuals for GAGEMAKER MIC TRAC MT-3000

Summary of Contents for GAGEMAKER MIC TRAC MT-3000

  • Page 2 ©2014 Gagemaker LP RCGPAMT30007-00 OMTFVB09-10 MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 3 Congratulations! Your decision to purchase a Gagemaker product above all others on the market demonstrates your confidence in our quality and workmanship. To ensure the high performance and operation of our product, we urge you to use the included reference materials.
  • Page 4 Setup Materials Needed: • • MIC TRAC™ MT-3000 base unit 5/32" hex wrench • • Gagemaker pivot arm gage 30 in/lb torque wrench • • Pivot arm fixture (TF-VB Block) and cap screws Cloth • • Contact point extension and contact point (certain gage styles) ZEP I.D.
  • Page 5 6. Use a 30 in/lbs torque wrench to secure the cap screws. 7. Clean the mounting surfaces of the pivot arm fixture using the cloth and ZEP I.D. Red cleaner. 8. Place the pivot arm fixture against the right receiver pad shoulder. MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 6 Note: MRP-1000 Upper Arm point must contact the lower portion of TF-1F block as shown at right. Mounting different styles of pivot arm gages MRP-1000 Upper Arm Touching TF-1F MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 7 Aligning the indicator dial on different styles of pivot arm gages 14. Turn the coarse adjust knob counterclockwise until the contact point on the pivot arm touches the flat face anvil. 15. Lock the coarse adjust lock. MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 8 1/16" hex wrench readout • • Seiko printer (optional) 5/64” hex wrench • • Gagemaker pivot arm or thread height gage Lightweight gage oil • • 5/32" hex wrench Gage Calibration Record • It is recommended to use a .0005” resolution indicator.
  • Page 9 9. Record any deviations on the Gage Calibration Record or in-house calibration report. Continue with remaining measurements at every .025” for the full travel of the indicator. 10. Accuracy = +/- .0005” on the dial indicator. MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 10 12. After calibrating all gages, be sure to remove the flat face anvil and the pivot arm fixture from the MT-3000. Oil the fixtures and return them to the storage case. MIC TRAC MT-3000 2014 Gagemaker, Inc. RCGPAMT30007-00...
  • Page 11 Gagemaker warrants its products to be free from defects in material and workmanship under normal operating conditions for 12 months from the date of shipment. This warranty is limited to repairing, or at Gagemaker’s option, replacing any product which is proven to have been defective at the time it was shipped and/or suffered damage during shipping, provided buyer has given Gagemaker written notice of any such claimed defect within 15 days of receipt.
  • Page 12 Gagemaker, LP, P.O. Box 87709, Houston, Texas 77287-7709 712 East Southmore Ave., Pasadena, Texas 77502 Phone: 713-472-7360Fax: 713-472-7241 Web site: www.gagemaker.com...