Avid Technology Pro Tools Carbon Read Me
Hide thumbs Also See for Pro Tools Carbon:

Advertisement

Read Me
Pro Tools | Carbon
This Read Me documents important compatibility information and known issues for Pro Tools | Carbon
For detailed compatibility information, including supported operating systems, visit the Pro Tools compatibility pages online.
Compatibility
Pro Tools | Carbon is supported by Pro Tools and Pro Tools | Ultimate 2020.11 or later only.
Pro Tools | Carbon is currently supported only on macOS 10.15.7 ("Catalina").
For the latest support information for Pro Tools | Carbon, visit at www.avid.com/carbon-support.
For detailed Pro Tools | Carbon system requirements, visit avid.secure.force.com/pkb/articles/compatibility/Carbon-Requirements.
Avid can only assure compatibility and provide support for hardware and software it has tested and approved.
For a complete list of optimizations for your Pro Tools computer, visit:
For complete Pro Tools system requirements and a list of qualified computers, operating systems, hard drives, peripherals, and third-
party devices, visit www.avid.com/compatibility.
If your computer only has Thunderbolt ports, an Avid-qualified AVB-capable Thunderbolt to Ethernet adapter is required.
A direct Network Interface connection between Pro Tools | Carbon and your computer is required. Network equipment such as routers,
hubs, and switches are not supported.
When using Pro Tools | Carbon with EUCON peripherals (such as S1), use a dedicated Network Interface to your Mac for
Pro Tools | Carbon.
General Compatibility
Avid-Qualified AVB-capable Thunderbolt to Ethernet Adapters Required for Pro Tools | Carbon
If your computer only has Thunderbolt ports, use an Avid-qualified AVB-capable Thunderbolt to Ethernet adapter.
Thunderbolt 2
Use an AVB-capable Thunderbolt 2-to-Gigabit Ethernet adapter, such as the Apple Thunderbolt to Gigabit Ethernet
Adapter.
Thunderbolt 3 (USB-C)
Use an AVB-capable Thunderbolt 3-to-Gigabit Ethernet adapter, such as the Apple Thunderbolt 3 (USB-C) to
Thunderbolt 2 Adapter connected to the Apple Thunderbolt to Gigabit Ethernet Adapter.
Not all Thunderbolt to Ethernet adapters are AVB-capable. For the latest information on connecting Pro Tools | Carbon to your
computer, visit the
Avid Knowledge Base for Pro Tools |
TrackPunch and DestructivePunch are Disabled with Pro Tools | Carbon (PT-265560)
If you are running Pro Tools | Ultimate software with Pro Tools | Carbon, TrackPunch and DestructivePunch are disabled.
Pro Tools | Carbon
11/9/20
Pro Tools Computer
Carbon.
.
Optimizations.
9329-66219-00 REV A
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pro Tools Carbon and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Avid Technology Pro Tools Carbon

  • Page 1 Read Me Pro Tools | Carbon ™ This Read Me documents important compatibility information and known issues for Pro Tools | Carbon For detailed compatibility information, including supported operating systems, visit the Pro Tools compatibility pages online. Compatibility Pro Tools | Carbon is supported by Pro Tools and Pro Tools | Ultimate 2020.11 or later only. Pro Tools | Carbon is currently supported only on macOS 10.15.7 (“Catalina”).
  • Page 2: Known Issues

    Known Issues The following sections document known issues you may encounter when using Pro Tools | Carbon, along with workarounds if they exist. If you encounter issues with Pro Tools | Carbon, visit the Troubleshooting Pro Tools | Carbon article on the Avid Knowledge Base.
  • Page 3: Routing Issues

    Routing Issues I/O Setup Output tab gets into incorrect state. (PT-266962) It is possible for the Output tab of I/O Setup to appear in an incorrect state after using either the Default Restore from Session com- mands, when the previous session had no assignment and was enabled.
  • Page 4 The input source signal is not muted during Count Off for record tracks in DSP Mode. (PT-265347) When Count Off is enabled in Pro Tools, the source signal of a DSP Mode–enabled record track can still be heard during Count Off. This does not occur if the record track is in Native Mode.
  • Page 5 Loud spikes on the ADAT input of an HD OMNI connected to the ADAT output of a Carbon unit while Carbon is booting. (PT-265779) It is possible for loud spikes to occur on the ADAT inputs of an HD OMNI interface (and possibly other devices that support ADAT) while a connected Pro Tools | Carbon is booting up.
  • Page 6 Inserting plug-ins on Auxiliary Input tracks in DSP Mode during playback may result in an “Automation is too dense” error. (PT-267129) It is possible for Pro Tools to display an “Automation is too dense” error if you try to insert certain resource-intensive plug-ins (such as some reverb and delay plug-ins) during playback.
  • Page 7: User Interface Issues

    Footswitch may have inverted behavior after changing footswitches while Pro Tools | Carbon is running. (PT-265571) Pro Tools | Carbon detects the footswitch polarity when it powers on. If you find that the footswitch you have connected is inverted from expected behavior, power cycle Pro Tools | Carbon while the footswitch is connected.
  • Page 8 — Pro Tools | Carbon 11/9/20...
  • Page 9 — Pro Tools | Carbon 11/9/20...

Table of Contents