ADTRAN ATLAS 800PLUS User Manual
  1. Manuals
  2. Brands
  3. ADTRAN Manuals
  4. Network Card
  5. ATLAS 800PLUS
  6. User manual

ADTRAN ATLAS 800PLUS User Manual

Adtran user manual network device atlas 800plus
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PLUS
ATLAS 800

USER MANUAL

Part Number 1200226L1
61200226L1-1A
September 1998

Advertisement

Table of Contents
loading

Related Manuals for ADTRAN ATLAS 800PLUS

Summary of Contents for ADTRAN ATLAS 800PLUS

  • Page 1: User Manual

    PLUS ATLAS 800 USER MANUAL Part Number 1200226L1 61200226L1-1A September 1998...
  • Page 2 DMS 100 is a registered trademark of Northern Telecom. 5ESS is a registered trademark of Lucent. Lucent Technologies is a registered trademark. 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 (256) 963-8000 © 1998 ADTRAN, Inc. All Rights Reserved. Printed in U.S.A.
  • Page 3 Chapter 9, SNMP Management on page 9-1, describes how to control the AT- PLUS LAS 800 • Chapter 10, ADTRAN Utilities on page 10-1, describes the Telnet, VT 100, and TFTP Server programs delivered with ATLAS 800 Appendices • Appendix A, System Event Logging on page A-1, describes the events ATLAS PLUS monitors.
  • Page 4 If they do, you will be given advance notice to give you an opportunity to maintain uninterrupted service. If you experience trouble with this equipment (ATLAS), please contact ADTRAN at (205) 963-8000 for repair/ warranty information. The telephone company may ask you to disconnect this equip- ment from the network until the problem has been corrected, or until you are sure the equipment is not malfunctioning.
  • Page 5 FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATE- MENT This equipment has been tested and found to comply with the limits for a Class A digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 6 AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL SERVICES • An affidavit is required to be given to the telephone company whenever digi- tal terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voiceband analog signals and trans- mitted on the network.
  • Page 7 AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.544 MBPS AND/ OR SUBRATE DIGITAL SERVICES For the work to be performed in the certified territory of ________________________(telco name) State of ________________ County of ________________ I, _____________________________ (name), _____________________ (business address), ____________________ (telephone number) being duly sworn, state: I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate digital services.
  • Page 8 I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as provided in the preceding paragraph, if so requested. _________________________________Signature _________________________________Title _________________________________ Date Transcribed and sworn to before me This ________ day of ________, 199___ _________________________________ Notary Public My commission expires:...
  • Page 9 CANADIAN EQUIPMENT LIMITATIONS The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, opera- tional, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facil- ities of the local telecommunications company.
  • Page 10 PLUS ATLAS 800 User Manual 61200226L1-1...

  • Page 11: Table Of Contents

    Switched Connection Maps ... 1-7 Testing... 1-7 Performance Monitoring ... 1-7 Chapter 2 Installation... 2-1 Before Installing the ATLAS_800PLUS... 2-1 Contents of ADTRAN Shipments... 2-1 Customer Provides ... 2-1 Checking the Power Connection ... 2-1 Grounding Instructions... 2-2 Rear Panel ... 2-2 Control In/Chain In ...
  • Page 12 Table of Contents Power Up Testing And Initialization ... 2-7 Self-Test ...2-7 Chapter 3 Operation ...3-1 Front Panel Layout... 3-1 LCD Window ...3-1 Enter...3-1 Up and Down Arrows...3-1 Cancel ...3-1 Numeric Keypad...3-1 Shift ...3-2 Operation Keys...3-3 System LED Description ...3-3 Channel Service Unit (CSU) Status ...3-4 Module Status LEDs...
  • Page 13 Filtering Traps ... 9-2 Standard Traps ... 9-2 DS1 Traps ... 9-3 DS1 Alarm Traps... 9-3 DS1 Alert Traps ... 9-5 Chapter 10 ADTRAN Utilities...10-1 Utilities delivered with the ATLAS_800PLUS... 10-1 Telnet ... 10-1 Menu Options ... 10-1 VT-100 ... 10-3 Menu Options ...
  • Page 14 Table of Contents Appendix C Warranty and Technical Support Information...C-1 Index ... Index-1 PLUS ATLAS 800 User Manual 61200226L1-1...

  • Page 15: List Of Figures

    List of Figures Figure 1-1. Point-to-Point Circuit... 1-2 Figure 1-2. Frame Relay Circuit ... 1-3 Figure 1-3. Digital Access Cross-Connect System (DACS) ... 1-4 Figure 1-4. T1 Bandwidth Management ... 1-5 Figure 1-5. WAN Overbooking ... 1-6 Figure 2-1. ATLAS_800PLUS Rear Panel... 2-3 Figure 2-2.
  • Page 16 List of Figures PLUS ATLAS 800 User Manual 61200226L1-1...

  • Page 17: List Of Tables

    Table 2-1. Control In/Chain In Pinout ... 2-4 Table 2-2. Control Out/Chain Out Pinout ... 2-5 Table 2-3. Network Pinout ... 2-6 Table 2-4. Ethernet 10BaseT Pinout ... 2-6 Table 6-1. Connections... 6-2 Table 7-1. Network Terminations ... 7-4 Table 7-2. User Termination ...
  • Page 18 List of Tables PLUS xviii ATLAS 800 User Manual 61200226L1-1...

  • Page 19: Chapter 1 Introduction

    Chapter 1 PRODUCT OVERVIEW The ATLAS_800 solutions for the wide area communication needs of medium-to-large corpora- tions and network access providers. ATLAS is an Integrated Access System with the most extensive support of dedicated bandwidth management and access switching in the industry. The ATLAS_800 ATLAS_800 communications drivers which allow the support of optional applications such as...

  • Page 20: Frame Relay

    Chapter 1. Introduction The modules include the following: • Quad Nx 56/64 Module • Quad T1/PRI Module • Octal Basic Rate ISDN Module • T3 Module • Async-232 Module • Modem-16 Module Frame Relay Frame relay is a packet-switched service that allows efficient transfer of bursty traffic in a WAN environment.

  • Page 21: Dedicated And Switched Connection Maps In A Single Platform

    The Frame Relay/Router upgrade option adds the capability for the ATLAS series of Integrated Access Devices to act as a voice/data FRAD, a frame relay switch, and an IP router in addition to the current available bandwidth manager and switch applications. Dedicated and Switched Connection Maps in a Single Platform The ATLAS_800 unique connection maps.

  • Page 22: Flexible Network Management And Maintainability

    10BaseT interface on the Base Unit provides an Ethernet connection for SNMP and Telnet connections. Additionally, T-Watch PRO, ADTRAN’s Microsoft agement system can allow end-to-end management with downstream ADTRAN T1 products. User configurations can be preserved in non-volatile memory and duplicated for managing multiple ATLAS implementations. ATLAS also supports FLASH upgrades for future enhancements.

  • Page 23: T1 Bandwidth Manager

    ATLAS is ideal for point-to-point configurations or access to public networks. For optimization of existing equipment and network resources, ATLAS can be paired with ADTRAN’s TSU product offerings to support a variety of data and analog voice applications (see Figure 1-4).

  • Page 24: Atlas_800Plus Features

    FEATURES Configuration and Management • VT 100 Emulation • T-Watch PRO, Microsoft Windows based GUI • SNMP, per MIB II (RFC1213), DS1 MIB (RFC1406), and ADTRAN private MIBs • Telnet • LCD Front Panel • Six levels of password protection and privileges Software Upgrade •...

  • Page 25: Isdn Switch Types

    ISDN Switch Types • 5ESS™, DMS-100™, National ISDN Dedicated Connection Maps • Up to five connection maps • Time of day/day of week configurable • Preserves signaling through cross-connect • No effect on non-configured channels Switched Connection Maps • Inbound and outbound call filtering and blocking Testing •...
  • Page 26 Chapter 1. Introduction PLUS ATLAS User Manual 61200226L1-1...

  • Page 27: Checking The Power Connection

    BEFORE INSTALLING THE ATLAS Carefully inspect the ATLAS_800 damage, file a claim immediately with the carrier and then contact ADTRAN Technical Support (see “Warranty and Technical Support Information” on page C- 1). If possible, keep the original shipping container for returning the...

  • Page 28: Grounding Instructions

    Chapter 2. Installation GROUNDING INSTRUCTIONS This section provides grounding instruction information from the Underwriters' Laboratory UL 1459 Standard for Safety: Telephone Equipment, of September 20, 1993. An equipment grounding conductor that is not smaller in size than the ungrounded branch-circuit supply conductors is to be installed as part of the cir- cuit that supplies the product or system.

  • Page 29: Control In/Chain In

    Control/Chain Connects to Chain In of another unit 10 Base T Control/ RJ-48C Connection Chain In Interface of Chain In CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONNEL ONLY CONTROL /CHAIN 10 BASE T ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS Blank panel covering an unused option slot Control In/Chain In...

  • Page 30: Control Out/Chain Out

    Chapter 2. Installation Control Out/Chain Out The Control Out/Chain Out is an RJ-48C port used to connect to another PLUS ATLAS_800 chain out pinout. The Control Out/Chain Out port output provides the following functions: • EIA-232 output to chain control to other units •...

  • Page 31: Network Connection

    NAME UNUSED TX DATA UNUSED RX DATA 6,7,8 UNUSED Network Connection The two eight-position modular jacks labeled NTWK 1 and NTWK 2 provide net- work connection. Table 2-3 on page 2-6 shows the pinout for the network connec- tors. The two Network Interface (NI) ports comply with the applicable ANSI and ®...

  • Page 32: Ethernet 10Baset Connection

    Chapter 2. Installation 6,7,8 Ethernet 10BaseT Connection The 10BaseT port (RJ-48C) provides an Ethernet LAN connection, which is used for TFTP, SNMP, and Telnet connection. See Table 2-4 on page 2-6 for the pinout. Connection The network connection is as follows: MON (Monitor) The MON test jack provides a bridged access jack for non-intrusive monitoring of the T1 circuits receiving data.

  • Page 33: Option Slot Arrangement

    OPTION SLOT ARRANGEMENT As viewed from the rear of the ATLAS_800 in Figure 2-2. All slots are functionally identical except slots 7 and 8, which also accommodate an optional power supply for redundancy. Figure 2-2. ATLAS_800 INSTALLING MODULES After installing the base ATLAS_800 you can install modules.
  • Page 34 Chapter 2. Installation Board-to-board interface test. A test pattern is sent from the controller through a loopback on all other boards and checked on the controller. This verifies the data path, clocks, and control signals If the front panel indicates a failure, see Troubleshooting on page B-1 to diag- nose the problem.

  • Page 35: Chapter 3 Operation

    Chapter 3 FRONT PANEL LAYOUT The ATLAS_800 select and set up the method of connectivity for controlling the unit through the front panel and use it to monitor the operation and status of the unit. Figure 3-1 on page 3-2 identifies the display panels and operation keys. LCD Window Displays menu items and messages in two lines by 16 characters in a backlit liq- uid crystal display (LCD).

  • Page 36: Shift

    Chapter 3. Operation Displays menu items and messages in 2 lines by 16 characters. Cancel Stops current activity and returns to the previous menu. Home Returns to the main menu. Shift Provides access to special function keys. Selects active menu items. Enter Quick access to the active alarm Alarm...

  • Page 37: Operation Keys

    Operation Keys Operation keys are ATLAS 800 tions. To activate an operation key, simultaneously press the front panel shift key and the operation key that you want to activate. To do this... Quickly accesses the active alarm display menus. (This function can be activated while any other menu item is in use.

  • Page 38: Channel Service Unit (Csu) Status

    Chapter 3. Operation Channel Service Unit (CSU) Status The CSU Status LEDs indicate the status of both network interfaces. This color light... OK (green) Test (yellow) Error (flashing red) Alarm (red) Module Status LEDs The Module Status LEDs display, by row, the operational condition (Status, Online, and Test) of each module installed in the option slots.

  • Page 39: Getting Started Using Terminal Menus

    VT-100 compatible client. The ADTRAN Utilities floppy disks (that you can install on a PC) contain both a VT-100 client and a customized Telnet program. See “ADTRAN Utilities”...

  • Page 40: Telnet

    Chapter 3. Operation You can access the terminal menu using a VT-100 terminal or a computer running VT-100 terminal-emulation software. The two basic connection methods sup- ported by the ATLAS_800 In port and a Telnet session. The following sections describe how to get started using both of these methods.

  • Page 41: Vt-100 Operation

    Select 2) CONFIG, S0) SYSTEM, 2) CHAIN PORT, then 1) BAUD RATE. Use the ADTRAN-provided VT-100 terminal adapter to connect the COM port of a VT-100 compatible terminal, or equivalent, to the eight-pin modular jack labeled CONTROL on the rear of the unit. This connection provides both local and remote configuration.

  • Page 42: T-Watch Pro

    Chapter 3. Operation T-Watch Pro T-Watch PRO is the ADTRAN Microsoft Windows management software pro- gram designed to control TSU units from a remote PC. It provides limited control over the configuration of the ATLAS_800 you can choose ATLAS_800 matically initiates a Telnet session by which you can connect to and manage the...

  • Page 43: Figure 4-1. Front Panel Lcd

    Front Panel Operation and Chapter 4 PLUS ATLAS 800 FRONT PANEL MENU STRUCTURE The ATLAS_800 items and data fields. All menu operations and data display in the LCD window. However, you only have access to limited configuration options through the front panel.

  • Page 44: Chapter 4 Front Panel Operation And Menu Structure

    Chapter 4. Front Panel Operation and Menu Structure To do this... Display the status of the ATLAS_800 Display the card type in each slot Perform limited configuration of the ATLAS_800 Monitor and modify miscellaneous settings View a log of system events Navigating the Front Panel The following sections provide general information on how to navigate the front panel menus.

  • Page 45: Front Panel Main Menu

    FRONT PANEL MAIN MENU The front panel Main menu provides limited configuration and control of the PLUS ATLAS_800 front panel Main menu. S0) SYSTEM 1) STATUS 2) CONFIG ATLAS MAIN MENU 1) TIME/DATE 2) SOFTWARE REV 3) UTIL 3) SELFTEST 4) SET PASSCODE 5) PASSWORD RESET 1) ACTIVE ALARMS...

  • Page 46: Status Menu

    Chapter 4. Front Panel Operation and Menu Structure Status Menu The Status menu branch lets you view the status of the ATLAS_800 Unit and any installed modules. S0 System The S0) System option displays status options that are available for the PLUS ATLAS_800 4-4) or Chain Port (see “Chain Port Status”...

  • Page 47: Configuration Menu

    Configuration Menu The Config menu branch provides limited configuration control of the PLUS ATLAS_800 S0 System S0) System displays configuration options that are available for the PLUS ATLAS_800 Configuration” on page 4-5) or Chain Port Configuration (see “Chain Port Configu- ration”...

  • Page 48: Utility Menu

    Unit ID This menu accesses the current Unit ID setting, which is the system identifier used for ADTRAN Data Link Layer Protocol (ADLP) con- figuration control (such as using T-Watch PRO). Editing or changing the Unit ID requires the use of a passcode if a passcode is defined.

  • Page 49: Software Rev

    Software Rev This option displays the current software revision level loaded into the base unit controller. This information is required when requesting assistance from ADTRAN Technical Support or when updates are needed. Press Cancel to exit this option. Selftest Selftest executes a system self-test, and the LCD displays the Pass or Fail when the test is complete.

  • Page 50: Show Results

    LCD window: CHALLENGE # and RESPONSE #. Call ADTRAN technical support, and tell them the challenge number. They use this to generate a random response number. Enter this response number in the RESPONSE # field, and ATLAS_800 tem password list.

  • Page 51: Alarm (Alrm) Menu

    Alarm (ALRM) Menu From the terminal menus you can view a log of system events. To control the types of events logged, a series of filters have been defined for each event source (System, T1/PRI, ISDN, Ethernet, etc.). Any event with a severity greater than, or equal to, the threshold defined in the event logging filter list is logged to the sys- tem event log.
  • Page 52 Chapter 4. Front Panel Operation and Menu Structure PLUS 4-10 ATLAS User Manual 61200226L1-1...

  • Page 53: Chapter 5 Using The Terminal Menu

    Chapter 5 PLUS ATLAS TERMINAL MENU STRUCTURE ATLAS_ items and data fields. All menus and data display in the terminal menu window, through which you have complete control of the connecting to the Terminal Menus” on page 3-5. The terminal menu is the access point to all other operations. Each terminal menu item has several functions and submenus that identify and provide access to spe- cific operations and parameters.

  • Page 54: Navigating The Terminal Menu

    Chapter 5. Using the Terminal Menu To do this... Assign dedicated connections between any two ports in the ATLAS_ Set global ATLAS_ parameters or set individual parameters for each port in ATLAS_ handles a switched call To edit terminal menu items, you must have the appropriate password (security) level.
  • Page 55 To do this... Move from right pane back to left pane Move around in each pane 61200226L1-1 Press one of these keys... Left arrow Right arrow Up arrow Down arrow Left arrow Right arrow PLUS ATLAS User Manual Chapter 5. Using the Terminal Menu Escape...

  • Page 56: Figure 5-1. Top-Level Terminal Menu

    Chapter 5. Using the Terminal Menu Menu Path Left Pane Tool Tip Menu Path Describes current position in the terminal menu structure. Lists available menus. Left Pane Right Pane Shows contents of currently selected menu. Describes ATLAS base unit. Tool Tip Brief description of currently selected command.

  • Page 57: Right Window Pane Notation

    Right Window Pane Notation This notation... [DATA] <+> highlighted menu item underlined field Using the Keyboard Keys You can use various keystrokes to navigate through the terminal menu, to man- age a terminal menu session, and to configure the system. Press Ctrl-Z to activate a pop-up screen listing the navigation keystrokes.

  • Page 58: Index

    Chapter 5. Using the Terminal Menu Session Management Keystrokes To do this... Log out of a session. Invalidate the password entry and return to the login screen. Refresh the screen. To save time, only the portion of the screen that has changed is refreshed.

  • Page 59: Getting Help

    Configuration Keystrokes (Continued) To do this... Insert a new list item. For example, add a new item to the pressing while the cursor is over the index number. Delete a list item. For example, delete an item from the pressing while the index number is active.
  • Page 60 Chapter 5. Using the Terminal Menu 40 alpha-numeric characters in this field, including spaces and special characters (such as an underbar). System Location Write security: 3; Read security: 5 Provides a user-configurable text string for the location of the This field is to help you keep track of the actual physical location of the unit. You can enter up to 40 alphanumeric characters in this field, including spaces and spe- cial characters (such as an underbar).

  • Page 61: System Status

    SYSTEM STATUS The System Status menu provides information on the status of the unit. Figure 5- 3 shows the submenu functions available in the System Status menu. Event Log Read security: 5 Displays the last 250 warning or failure messages sent—including the day, date, and priority of the message.
  • Page 62 Chapter 5. Using the Terminal Menu If you clear the event log, you cannot retrieve the data. Ethernet Port Read security: 5 Displays status information about the Ethernet port. These fields are read-only. An asterisk (*) indicates activity for the item. I/F Status Indicates the current status of the 10BaseT port.
  • Page 63 Data Tables This statistic... Resource Type Current Average Minimum 0 (zero) available Hour Data Reset Configuration Write Security: 4 Read Security: 5 Configures the statistics displayed under data tables. This option... Display Formt Reset Mode Chain Port Signal Leads Read security: 5 Displays the state of the following options (these fields are read-only).

  • Page 64: System Configuration

    ADLP Address Write security: 2; Read security: 5 Shows the system ADTRAN Data Link Layer Protocol (ADLP) address for con- necting remote devices to management software (such as T-Watch PRO). The allowable range is between 2 and 65520. Enter a value not used by any of the TSU units controlled by the management software.
  • Page 65 Max Telnet Sessions Write security: 3; Read security: 5 Defines the maximum number of Telnet sessions that can be active at the same time. Enter a number between 0 and 100 in this field. If you enter zero in this field, you will not be able to use Telnet. Only enter zero if you want to completely lock out Telnet access.
  • Page 66 Chapter 5. Using the Terminal Menu Port Speed Write security: 2; Read security: 5 Specifies the baud rate of the port. Select either 2400 or 9600. If you are using Dial for Port Type, ensure that the Port Speed setting matches the modem baud rate.
  • Page 67 This option... IP Address Privileges Get Name Set Name Trap Transmission Write security: 3; Read security: 5 Enables and disables SNMP trap transmission. Authen Trap Transmission Write security: 3; Read security: 5 Enables and disables the authentication failure trap. Traps Destination Write security: 3;...
  • Page 68 Syslog Setup Write Security: 3 Read Security: 5 Configures the ATLAS Syslog client for use with a Syslog server (supplied on Adtran /Utility disk). Transmission Enables or disables the transmission of log events to the external Syslog server.
  • Page 69 5-17. If you lose or forget the tact ADTRAN technical support for help in resetting the password. In order to reset the password, you must have access to the front panel. For details on reset- ting the password, see Password Reset on page 1-30.

  • Page 70: System Utility

    Chapter 5. Using the Terminal Menu To change the password, follow this procedure: Select the Password field—a new Password field displays. Type the new password in the Enter field. Type the new password again in the Confirm field. The password can contain up to 12 alphanumeric characters. You can also use spaces and special characters in the password.
  • Page 71 Chapter 5. Using the Terminal Menu ing you to select Slot 1 through Slot 8 or All Modules of a Type (this is useful if PLUS there are several identical modules installed in the ATLAS_ Module Type Write security: 1; Read security: 5 Displays the type of module that is selected in the Module Slot option.
  • Page 72 You can also use Config Transfer to retrieve a configuration file from a TFTP server. ADTRAN delivers a TFTP program with can configure any PC running Microsoft Windows with this software to store the configuration file. See “TFTP Server” on page 10-4 for details on how to use the TFTP Server software with these menu items to transfer configuration files.
  • Page 73 TFTP Server IP Address Write security: 3; Read security: 5 Specifies the IP address of the TFTP server. Get this number from your system administrator. TFTP Server Filename Write security: 3; Read security: 5 Defines the name of the configuration file that you will transfer to or retrieve from the server.

  • Page 74: Figure 5-6. View Self-Test Log

    Chapter 5. Using the Terminal Menu View Self-test Log Read security: 5 Displays a read-only, time-stamped log of the tests conducted and the Pass/ Fail results. The tests associated with the system controller include the follow- ing: This test... Flash BootRom DSP RAM RTC RAM...

  • Page 75: Modules

    MODULES The Modules menu provides options that allow you to configure and control the installed option modules as well as the controller T1/PRI ports. Figure 5-7 shows the Modules menu. (Write security: 3; Read security: 5) The controller board (slot 0) has two T1/PRI interface ports. This section only describes the module options available for the T1/PRI interface ports.
  • Page 76 Chapter 5. Using the Terminal Menu If a module is installed, the module type automatically displays the name of the installed module, and cannot be set to any other option. Menu Displays additional status and configuration menus for the selected module. To access the submenus for this item, use the Arrow Keys to scroll to the Menu col- umn for the module you want to edit, and press Enter.

  • Page 77: Atlas_ 800Plus Controller T1/Pri Submenu Items

    Empty The system controller has not detected the presence of a module in the sys- tem, nor has a module been manually enabled for this option slot. Offline The modules is installed but has been taken Offline by a user. The module is still responding to controller polls.
  • Page 78 Chapter 5. Using the Terminal Menu This alarm... D Channel Sync (D-Chan) Receive Level (Rx Level) DS0 Status Read security: 5 Indicates usage on a DS0 basis for each port. These options are read-only. DS0 status... Sig Status Read security: 5 Indicates signaling of all 24 DS0s.
  • Page 79 Field... Provides this status information... Performance: 15 Min Write security: 3; Read security: 5 In the Performance 15 min. menu, the Performance data for the previous 15 minute window is stored. Refer to “Performance: Current” on page 5-26 for a detailed description.

  • Page 80: Dedicated Maps

    Chapter 5. Using the Terminal Menu Test Initiates different types of tests and displays test results. These commands temporarily disrupt service. This submenu... Test Loc LB (Local Loopback) Read security: 5 Remote LB (Remote Loopback) Write security: 4; Read security: 5 Pattern Write security: 4;...

  • Page 81: Figure 5-8. Dedicated Maps Menu

    Activate Map Write security: 3; Read security: 5 PLUS ATLAS_ optional name designator. You can manually activate a map by pressing Enter in this field, and then selecting the appropriate map. You can also select Auto, which permits the maps to activate automatically depending on the time and day set- tings defined in the field Activate Time (a submenu of “Create/Edit Maps”...
  • Page 82 Chapter 5. Using the Terminal Menu Displays the number of the dedicated map connection. If you press I in this field, tion, numbered consecutively. FROM Slot Write security: 3; Read security: 5 Specifies the slot to use for the FROM connection. Select this option, and a list of all of the slots and the modules installed in the slots dis- plays.

  • Page 83: Figure 5-9. Trunk Conditioning

    Trunk Conditioning Trunk conditioning is a process which sets known values in the sig- naling bits and the data field for outgoing DS0s which are cross con- nected to a T1 port which is experiencing alarms (see Figure 5-9). The trunk conditioning process consists of a 2.5-second transmission (indicating call termination), followed by a continuous transmission signaling the final condition (Seized or Idle) as chosen by the user.
  • Page 84 Chapter 5. Using the Terminal Menu Defining Trunk Conditioning Write security: 3; Read security: 5 Fault signaling is only visible when RBS is on. TO Slot Write security: 3; Read security: 5 This is the same as From Slot (described on page 5-30) except this option designates the second end of a connection.

  • Page 85: Dial Plan

    option, you can select AUTO in the Activate Map field (see “Activate Map” on page 5-29). Enbl Day Write security: 3; Read security: 5 Specifies which days of the week the map is active. Dial Plan Write security: 3; Read security: 5 Dial Plan includes menus for setting global ATLAS switch parameters and for set- ting individual parameters for each port in ATLAS that handles a switched call (see Figure 5-10).
  • Page 86 Chapter 5. Using the Terminal Menu ule type being used is not reflected in the Interface Configuration section, please refer to the option module manual for information on the interface parameters. Slot/Port Write security: 3; Read security: 5 These fields are used to select the ATLAS port that terminates a Network con- nection.
  • Page 87 Accept Numbers This field designates which numbers this end point will pass on toward the Network (PSTN). The accept list may consist of multiple entries. The num- bers are defined using “wild cards”: Example: 1-800-$ would only permit toll free long distance calls to 1-800. If this were used, then a second accept # would need to be specified - NXX- XXXX.
  • Page 88 Chapter 5. Using the Terminal Menu Out#Rej Write security: 3; Read security: 5 This submenu defines the parameters for the outgoing calls that ATLAS will not send to the Network. Reject Numbers This field identifies which numbers this end point will not pass on toward the Network (PSTN).
  • Page 89 Slot/Port (Select list of option modules/ports) Write security: 3; Read security: 5 These fields are used to select the ATLAS port that terminates a User connec- tion. There may be more than one “end point” associated with a particular port. If a T1 port is connected to a channel bank with analog voice cards, each DS0 or a group of DS0s may have a different phone number.
  • Page 90 Chapter 5. Using the Terminal Menu Accept Numbers Write security: 3; Read security: 5 This field designates which numbers this end point will accept (ter- minate) from the Network (PSTN). The accept list may consist of multiple entries. The numbers are defined using “wild cards”: Example: accepted by this end point.

  • Page 91: Global Parameters

    Treat Call As Write security: 3; Read security: 5 This allows you to treat an incoming voice call (as designated by the ISDN call type identifier) as a data call. This is useful if the ISDN lines are provisioned for voice but are actually being used for data. Out#Rej (Outgoing Number Reject List) Write security: 3;...
  • Page 92 Chapter 5. Using the Terminal Menu will only be invoked if the dialed number does not match one of the patterns set in the Number Complete Template menu. Area Code Write security: 3; Read security: 5 The local area code. This is used for sending caller ID to the Network. Number Complete Template Write security: 1;...

  • Page 93: Interface Configuration

    Interface Configuration The Interface Configuration option for the Dial Plan menu sets configuration param- eters for the end point. These parameters vary by the type of port selected. The following sections describe the configuration options for each available type of module and port that existed when this manual was released.
  • Page 94 Chapter 5. Using the Terminal Menu When a 4ESS is configured, many installations will require the national form where possible; this may also be the preferred form in 10-digit calling areas. Strip MSD Write Security: 3 Read Security: 5 This option allows a selected quantity of the Most Significant Digits (MSD) of a dialed number for ATLAS to be stripped prior to being forwarded out of the port.
  • Page 95 ID Presentation Sends to the Network control information for the presentation of Caller ID (Presentation Allowed; Presentation Restricted; Number Not Available.) ID Number Value for Caller ID to be sent to the Network( i.e. 256 963 8020). Source ID The Source ID field simplifies the creation of a Dial Plan in applications where the criteria for switching calls to a certain end point is a function of which end point originated the call.
  • Page 96 Chapter 5. Using the Terminal Menu DS0s Available Read security: 5 Indicates which DS0s of the T1 have been defined in this switched end point (indicated by “! “), in another switched end point (indicated by “s”), or in a Dedi- cated Map (indicated by “n”).
  • Page 97 DID Prefix Write security: 3; Read security: 5 Defines to ATLAS the prefix digits which are not received as a part of the DID number. ATLAS uses the combination of prefix and DID number to deter- mine the User end point that should receive the incoming call. This option only displays if Direct Inward Dialing (DID) is set to Enabled.

  • Page 98: Quad T1/Pri Module (User Termination/Pri)

    Chapter 5. Using the Terminal Menu Quad T1/PRI Module (User Termination/PRI) When you are working in the User Termination section of the Dial Plan menu, the Slot is defined as a T1/PRI module, and Sig is set to PRI, the following configura- tion options are available: Switch Type Write security: 3;...
  • Page 99 Called Digits Transferred Write security: 3; Read security: 5 Defines to ATLAS the number of called-number digits to forward. When attached to a PBX, the PBX may be provisioned to expect to receive fewer than all of the called digits of the incoming call. This would normally be set to All. Outgoing Caller ID Write Security: 3 Read Security: 5 This item allows the user to insert a called ID to be added to outgoing calls (com-...

  • Page 100: Quad T1/Pri Module (User Termination/Rbs)

    Chapter 5. Using the Terminal Menu Quad T1/PRI Module (User Termination/RBS) When you are working in the User Termination section of the Dial Plan menu, the Slot is defined as a T1/PRI module, and Sig is set to RBS, the following configura- tion options are available: First DS0/Number of DS0s Write security: 3;...

  • Page 101: Quad Nx56/64 Module Interface Configuration

    Direct Inward Dialing Defines to ATLAS whether DID is used by the user equipment. If DID is Enabled, then the following information must be defined: DID Digits Transferred Defines the number of digits ATLAS is to send on to the user equipment. This field only displays if Direct Inward Dialing is set to Enabled.

  • Page 102: Quad Nx56/64 Module (User Termination)

    Chapter 5. Using the Terminal Menu The Quad Nx56/64 can only serve as a user termination end point Quad Nx56/64 Module (User Termination) When you are working in the User Termination section of the Dial Plan menu, and the Slot is defined as a QuadNx56/64 module, the following interface configura- tion options are available: Ports Available Indicates which of the four ports of the Quad Nx56/64 module have already been...

  • Page 103: Octal Bri Module (User Termination)

    switch for this line. Each BRI may have one or more phone numbers and SPIDs. The SPID Number list submenu defines to ATLAS these parameters. Phone Number SPID Number Calls Audio Speech Octal BRI Module (User Termination) The Octal BRI with a “U” interface is capable of acting like the Network while interfacing to user equipment (terminal adapters).
  • Page 104 Chapter 5. Using the Terminal Menu Calls Audio Speech 5-52 For User terminations, the number of calls is fixed at 2. These options reflect what the Network has provisioned for this SPID. If the BRI was purchased with different services provisioned for the SPIDs, then the call must match the services supported.

  • Page 105: Chapter 6 Creating A Dedicated Map

    Creating a Dedicated Map Chapter 6 OVERVIEW A Dedicated Map defines connections for dedicated bandwidth between ports and grooms and cross-connects bandwidth between T1 ports. Any ATLAS port supporting dedicated bandwidth can be mapped to any other port capable of sup- porting dedicated bandwidth.

  • Page 106: Figure 6-2. Slot 0 Module Configuration Menu

    Chapter 6. Creating a Dedicated Map Name ATLAS 800 T1-A Controller T1 Data Slot 0 Port 1 T1-B Controller T1 Data Slot 0/Port 2 T1-C Quad T1/PRI Data Slot 1/Port 1 T1-A Controller T1 Voice Slot 0/Port 1 T1-B Controller T1 Voice Slot 0/Port 2 T1-C...
  • Page 107 Navigate to the Port index number of the second port and paste the configuration by pressing P. Repeat for the first port of the T1/PRI card located in Slot 1. Navigate to the V.35 Port Configuration menu and repeat the configuration of the first port followed by copy and paste to the second and third ports.

  • Page 108: Figure 6-3. Completed Dedicated Map

    Chapter 6. Creating a Dedicated Map O. Set RBS to On for the Voice connections. (Optional) Using the Configuration submenu, set the trunk conditioning (Signaling and Data code) desired for T1 failure. Q. Repeat for the remaining Voice connections as in steps F through J above. A connection is not actually “made”...

  • Page 109: Chapter 7 Creating A Dial Plan

    Chapter 7 OVERVIEW The ATLAS Dial Plan acts as the numbering plan for switched connections. This menu defines to ATLAS the phone numbers and features associated with dial-up ports. ATLAS supports Robbed Bit Signaling (RBS) T1 interfaces using DTMF dialing, Primary Rate ISDN (PRI) and Basic Rate ISDN (BRI). In order to operate as a switch, ATLAS must be able to terminate network connections (Network Ter- minations) and emulate the Network into other termination equipment (User Ter- minations).

  • Page 110: Understanding The Dial Plan

    Chapter 7. Creating a Dial Plan One ATLAS 800 nates” the network. In the example in Figure 7-2, ATLAS A is emulating the net- work and the PRI interface is a User Termination, while the PRI interface of ATLAS B is a Network Termination. Understanding the Dial Plan The Dial Plan menus are subdivided into three separate menus.

  • Page 111: Plan The Dial Plan

    Plan the Dial Plan Determine the provisioning of the Network, and the attached equipment (video equipment and PBX). Network PRI User Equipment Enter the local Area Code number (needed for Caller ID operation) under the Global Parameter submenu below the Dial Plan menu. Determine which ports are Network Terminations and which are User Terminations.
  • Page 112 Chapter 7. Creating a Dial Plan For our example there is one PRI port terminating the network (PRI - A) and three BRIs (BRI A, B, C). (See Table 7-1 on page 7-4.) Table 7-1. Network Terminations NAME PORT OUTGOING ACCEPT # PRI-A Controller T1...

  • Page 113: Implement The Dial Plan

    For User Termination, there is one PRI, one RBS T1, and three BRIs (see Table 7-2 on page 7-5). NAME PORT BRI D,E,F Octal BRI Slot 1, Port 4-5,6 PRI-B Controller T1 Slot 0, Port 2 T1-A Slot 2, Port 1 Implement the Dial Plan Using the terminal menus, navigate to the Dial Plan menu.

  • Page 114: Figure 7-4. Completed Network Map

    Chapter 7. Creating a Dial Plan Select the Out (Outgoing) # Accept submenu. Enter $ in the number field. Leave all other selections set to default (Enabled). Select the Out (Outgoing)# Reject submenu. Since no outgoing numbers need to be rejected at this port, no entry is required. Select Interface Configuration (Ifce Config) submenu.

  • Page 115: Figure 7-5. Completed User Map

    Chapter 7. Creating a Dial Plan After completion, the User Map should appear (see Figure 7-5). Figure 7-5. Completed User Map A connection is not actually “made” (available) until you press Esc to move the cursor to the index number or move the cursor onto another connection line. PLUS 61200226L1-1 ATLAS 800...
  • Page 116 Chapter 7. Creating a Dial Plan PLUS ATLAS 800 User Manual 61200226L1-1...

  • Page 117: Chapter 8 Updating Firmware

    Ensure the communications software package being used has flow control turned off. Update Firmware Using XMODEM Obtain the appropriate update file for the particular module from ADTRAN Technical Support. For more information on how to contact ADTRAN Technical Support, refer to “Warranty and Technical Support Information” on page C-1.

  • Page 118: Figure 8-1. Update Firmware Menu Interface

    Chapter 8. Updating Firmware A Level 2 password is required for performing updates of any module within ATLAS. Please consult the ATLAS administrator if you do not know the password. Select the System Utility menu. Select Update Firmware. Figure 8-1 shows the Update Firmware menu. Move to the Module Slot field.
  • Page 119 Please refer to terminal emulation software documentation for help. When specifying the filename, make sure the file transferred is the one provided by ADTRAN. Otherwise, the update will not complete successfully. 16. Because XMODEM data is being transferred in-band through the menu interface, the VT-100 menus of ATLAS will be inoperable from the Chain In port.

  • Page 120: Update Firmware Using Tftp

    Technical Support, refer to “Warranty and Technical Support Information” on page C-1. Copy the update file provided by ADTRAN to a network server that supports TFTP server requests. Please record the IP address of the server and full path location of the update file to be downloaded by the ATLAS TFTP client.

  • Page 121: Figure 8-2. Update Firmware Menu Interface

    Only Modules which are upgradable display as choices for the Module Type field when updating all modules of a type in the ATLAS. Select TFTP for the Transfer Method. The ATLAS menu now displays two additional fields which must be entered for TFTP transfers. 10.
  • Page 122 Previous Update Status field will display the appropriate error message. Please go to step 7 and attempt the update process again. If the same error occurs, please contact ADTRAN Technical Support. 19. If the update of the module was successful, the module will either restart immediately and resume operation or restart at the specified time and day of the week, depending on your selection.

  • Page 123: Chapter 9 Snmp Management

    Chapter 9 UNDERSTANDING SNMP As local area network (LAN) environments became standardized over the past ten years, multi-vendor equipment grew with competition. It became necessary to manage the various vendor equipment from a single control console. Thus, SNMP emerged as the standard for managing commercial TCP/IP networks. The term SNMP broadly refers to the message protocols used to exchange infor- mation between the network management station and the managed devices, as well as to the structure of network management databases.

  • Page 124: Traps

    Chapter 9. SNMP Management TRAPS An SNMP trap is a message sent by a Network Device, such as the ATLAS, to report an operational anomaly or alarm condition. DEFINING A TRAP DESTINATION LIST For each trap event, a trap message will be sent to each member of the Trap Desti- nation List.

  • Page 125: Ds1 Traps

    DS1 TRAPS The ATLAS will support RFC1406, the DS1 standard MIB, as well as the ADT- RAN DS1 MIB, an extension to RFC1406. The ADTRAN DS1 groups provide the capability to send traps for DS1 Alarm failures and Performance Threshold Cross- ing Alerts.
  • Page 126 Chapter 9. SNMP Management Alarm adATLAS800NoAlarm adATLAS800RxYellow adATLAS800TxYellow adATLAS800RxAIS adATLAS800TxAIS adATLAS800RedAlarm adATLAS800LOS When enabled, the ATLAS will send Alarm Traps to the each member of the Trap Destination List upon detecting status bit changes in dsx1LineStatus. Each status change sets an event bit = 1 in the adDS1LineEvent variable in the DS1 Alarm Table.

  • Page 127: Ds1 Alert Traps

    DS1 ALERT TRAPS RFC1406 also defines a series of Current and Total Alert threshold values. You can enable the ATLAS to send an Alert Trap message to each member of the Trap Des- tination List when accumulated error statistics exceed these threshold values. Table 9-4 describes the Alert Traps supported by the ATLAS for events that have occurred in the last 15-minute interval.
  • Page 128 Chapter 9. SNMP Management Table 9-5 describes the Total Alert Traps, which describe events that have occurred in the last 24-hour interval. Total Alert Severity adATLAS800TotalES WARNING adATLAS800TotalSES WARNING adATLAS800TotalSEFS WARNING adATLAS800TotalUAS MAJOR adATLAS800TotalCSS WARNING adATLAS800TotalPCV WARNING adATLAS800TotalLES WARNING adATLAS800TotalLCV WARNING When one of the Total Alert thresholds is exceeded, the corresponding event bit is set to 1 in the adDS1TotalAlert variable in the DS1 Alert Table.

  • Page 129: Chapter 10 Adtran Utilities

    Chapter 10 UTILITIES DELIVERED WITH THE ATLAS ADTRAN delivers several software utilities on three diskettes with the ATLAS_800 and to transfer configuration files to and from TFTP servers. The diskettes also include the ATLAS_800 tory). The utilities all run on Microsoft Windows 3.1 or higher. The following sec- tions describe the Telnet, VT-100, and TFTP Server utilities.

  • Page 130: Figure 10-1. Add New Dialog Box

    Chapter 10. ADTRAN Utilities Port You can choose several options from the Port pulldown menu: • Telnet: establishes a Telnet session • Echo: provides a loopback for troubleshooting • Discard: bit bucket; discards data • Daytime: returns the time •...

  • Page 131: Options Menu

    This option allows you to changes various serial COM port settings (see Figure 10-3). 61200226L1-1 PLUS . The VT-100 display is almost identical to the PLUS for a VT-100 session, refer to “VT- PLUS ATLAS User Manual Chapter 10. ADTRAN Utilities PLUS when the PC is directly 10-3...

  • Page 132: Options Menu

    Chapter 10. ADTRAN Utilities Options Menu Connect Provides the options Transmit Wakeup and Transmit Refresh. Refresh Screen Redraws the screen. Colors These commands change the color of the background screen and text. Local Echo and Auto Repeat These options are the same as in the Telnet interface (see page 10-3 for details).

  • Page 133: Menu Options

    To Printer Sends the information in the Log field to the default printer. 61200226L1-1 Figure 10-4. TFTP Server Interface PLUS ATLAS User Manual Chapter 10. ADTRAN Utilities 10-5...

  • Page 134: Saving The Current Configuration To A Tftp Server

    Set TFTP Server IP Address to the IP address of the machine running the TFTP server program. If you are using the ADTRAN TFTP server, the IP address displays in the Status field. Change TFTP Server Filename to a unique filename. This will be the name of the configuration file to save to the remote server.

  • Page 135: To Retrieve The Configuration From A Tftp Server

    Complete, and the Current Transfer Status field displays Idle. The file is now present on the TFTP server. (For the ADTRAN TFTP Server, it is stored in the installation directory or the directory you specified.) TFTP is not secure. No passwords are required for client access. Anyone can ac- cess files through the IP port on the server machine if they know the target file’s...
  • Page 136 Chapter 10. ADTRAN Utilities If the upload completes successfully, the unit reboots automatically and runs using the new configuration. If the upload fails, an error message is present in the Previous Transfer Status field. If the TFTP server cannot be contacted, the attempt takes approximately 20 seconds to timeout.
  • Page 137 Appendix A This section describes the entries that may be logged by the system event log. Of particular importance is the log event’s Category – this is the minimum severity level that must be set in order that the event be logged. Use caution when changing Categories from their default levels.

  • Page 138: Appendix A System Event Logging

    Appendix A. System Event Logging Event System Cold Start – generated 5 seconds after the completion of system initializa- tion. SNMP Authentication Failure – generated if the ATLAS receives an SNMP request from an SNMP manager defined in the ATLAS SNMP Communities list but with a community name that does not match the community name defined in the SNMP Communities list.
  • Page 139 Table A-2. Event Call rejected – no such number in dial plan Call rejected – number is on outgoing reject list Call successfully routed Call rejected -- all end points busy Event Clock Slip Alarm Active Clock Slip Alarm Cleared Pll Alarm Active Pll Alarm Cleared External Clock Alarm...
  • Page 140 Appendix A. System Event Logging Table A-3. Event 511 Test Pattern Deactivated DTR Asserted DTR Dropped RTS Asserted RTS Dropped DCD Asserted DCD Dropped CTS Asserted CTS Dropped Event Red Alarm Set Red Alarm Cleared Yellow Alarm Set Yellow Alarm Cleared Blue Alarm Set Blue Alarm Cleared LOS Alarm Set...
  • Page 141 Table A-4. Event Tx Yellow Alarm Set Tx Yellow Alarm Cleared D Channel Alarm Set D Channel Alarm Cleared Line Loopback Active Payload Loopback Active Loopback Cleared Current T1 Errored Seconds Threshold Exceeded Current T1 Severely Errored Seconds Threshold Exceeded Current T1 Severely Errored Framing Seconds Threshold Exceeded...
  • Page 142 Appendix A. System Event Logging Table A-4. Event Total T1 Severely Errored Fram- ing Seconds Threshold Exceeded Total T1 Unavailable Seconds Threshold Exceeded Total T1 Controlled Slip Sec- onds Threshold Exceeded Total T1 Path Code Violations Threshold Exceeded Total T1 Line Errored Seconds Threshold Exceeded Total T1 Line Code Violations Threshold Exceeded...
  • Page 143 Table A-6. Event SPID Failed Major D Channel Down Major Incorrectly formatted IE Major SPID Retry in progress Minor SPID Unregistration Warning attempted No Matching SPID Warning found No Matching SPID Warning found ISDN line released Normal BRI LT configuration suc- Normal cessful BRI NT configuration...
  • Page 144 Appendix A. System Event Logging Table A-6. Event SPID Registration com- Normal plete SPID Registration in Normal progress Call Rejected Normal D Channel Up Normal Dialing number Information Call not accepted Information Call cleared Information Call busy Information Call connected Information Call ringing Information...
  • Page 145 Cause Code Message UNASSIGNED_NUMBER NO_ROUTE CHANNEL_UNACCEPTABLE NORMAL_CLEARING USER_BUSY NO_USER_RESPONDING CALL_REJECTED NUMBER_CHANGED DEST_OUT_OF_ORDER INVALID_NUMBER_FORMAT FACILITY_REJECTED RESP_TO_STAT_ENQ UNSPECIFIED_CAUSE NO_CIRCUIT_AVAILABLE NETWORK_OUT_OF_ORDER TEMPORARY_FAILURE NETWORK_CONGESTION ACCESS_INFO_DISCARDED REQ_CHANNEL_NOT_AVAIL PRE_EMPTED FACILITY_NOT_SUBSCRIBED OUTGOING_CALL_BARRED INCOMING_CALL_BARRED BEAR_CAP_NOT_AVAIL SERVICE_NOT_AVAIL CAP_NOT_IMPLEMENTED 61200226L1-1 ISDN Cause Codes Table A-7. Code PLUS ATLAS 800 User Manual Appendix A.
  • Page 146 Appendix A. System Event Logging Table A-7. Cause Code Message CHAN_NOT_IMPLEMENTED FACILITY_NOT_IMPLEMENTED INVALID_CALL_REF CHAN_DOES_NOT_EXIST INCOMPATIBLE_DEST INVALID_MSG_UNSPEC MANDATORY_IE_MISSING NONEXISTENT_MSG WRONG_MESSAGE BAD_INFO_ELEM INVALID_ELEM_CONTENTS WRONG_MSG_FOR_STATE TIMER_EXPIRY MANDATORY_IE_LEN_ERR PROTOCOL_ERROR INTERWORKING_UNSPEC Cause Code IEs that are non-Q.931 (Coding Standard field is not 0) are logged with the following format: <message>...
  • Page 147 Each Cause Code IE log entry will end with a location designation. These desig- nations are shown in Table A-8: Table A-8. Code INTL INWK Table A-9. Event ISDN Layer 2 (LAPD) Message. Provides a hex dump of the entire LAPD frame Table A-10.
  • Page 148 Appendix A. System Event Logging Table A-11. Event ISDN Information Elements. Provides a hex dump of the ISDN IE sent with a call control message A-12 Source: ISDN Information Elements Console Log Category String Information <message contents> PLUS ATLAS 800 User Manual Front Panel Display String...

  • Page 149: Appendix B Troubleshooting

    Appendix B SYMPTOM POSSIBLE CAUSES Power-up Self-Test Modules seated improp- Fails erly, module failure System Timing Selected Timing Source is Source Unlocked not present or clock is out (displayed on Ter- of tolerance minal Interface, “System Status”) Cannot pass data Misconfiguration, improper from T1 interface cabling...
  • Page 150 Appendix B. Troubleshooting Table B-1. SYMPTOM POSSIBLE CAUSES Switched calls are Misconfiguration not working Cannot communi- Misconfiguration, improper cate with ATLAS cabling with VT 100 con- nected to the Con- trol/Chain In Port Cannot establish Max Telnet sessions set to Telnet session with 0, IP address of ATLAS ATLAS...

  • Page 151: Atlas 800 Plus User Manual

    Appendix C WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADT- RAN Equipment Warranty and Repair and Return Policy Procedure.
  • Page 152 CAPS directly at the following number: RMA Department Identify the RMA number clearly on the package (below address), and return to the following address: ADTRAN Customer and Product Service 6767 Old Madison Pike Building #6 Suite 690 Huntsville, Alabama 35807 RMA # _____________...
  • Page 153 4-9 new (Telnet utility) 10-2 add password 5-17 address ADLP 5-12 ADLP address 5-12 ADTRAN utilities 10-1 ADTRAN data link layer protocol address 5-12 alarm blue 5-25 red 5-25 status 5-25 system 5-10 yellow 5-25, 5-27 yellow auto TX 5-27...
  • Page 154 Index called digits transferred 5-42, 5-47 caller ID number 5-49 cancel 3-1, 3-2 menu 4-2 cancel key 3-2 capture 10-3, 10-4 category 5-9 logging A-1 chain in 2-3 pinout 2-4 chain out 2-2, 2-4 pinout 2-5 chain port configure 5-13 framing errs 5-12 overrun errs 5-12 Rx bytes 5-11...
  • Page 155 description 1-4 data 56 kbps accept 5-38 56 kpbs reject 5-39 64 kbps accept 5-35, 5-38 reject 5-36, 5-39 data field 4-2 set 4-2 data tables 5-11 configuring 5-11 date 4-6 current 5-16 restart schedule 5-19 restart system 5-19 set 5-8 daylight savings 5-16 chain port status 4-4 data carrier detect 5-11...
  • Page 156 Index end point configuration 5-41 enter dedicated map connections 5-29 enter key 3-1, 3-2 entry edit (Telnet utility) 10-2 erase alarm history 4-9 event log 5-9 selftest log 5-22 test results 4-8 error LED 3-4 errored seconds 5-26 errors inject 5-28 ES 5-26 ESF 2-5 ethernet...
  • Page 157 configuration from TFTP server 10-7 global parameters 5-39 global switch parameters 5-33 green CSU LED 3-4 green module status LED 3-4 ground start 5-48 grounding 2-1 grounding instructions 2-2 hardware revision 5-25 help 5-7, C-1 history clear 4-9 view 4-9 home 3-2 home key 3-3 I/F status 5-10...
  • Page 158 Index user map complete 7-7 map name 5-29 maps dedicated 5-28 nailed 5-28 max telnet session 5-13 memory installed 5-8 menu alarm 4-9 configuration 4-5 item activate 4-2 module 5-24 modules 5-23 path 5-4 session 10-1 status 4-4 submenu 5-25 system status 5-9 system utility 5-18 util 4-6...
  • Page 159 switch type 5-51 user termination 5-51 offline 5-25 offline/no response 5-25 OK LED 3-4 online 5-24 online help 5-7 online LED 3-4 operating front panel 4-1 terminal menu 3-5, 5-1 VT 100 3-7 operating ATLAS 800 PLUS 3-5 operation 3-1 operation keys 3-3 option slot arrangement 2-7...
  • Page 160 Index Quad T1/PRI interface configuration 5-41 network termination/PRI 5-41 network termination/RBS 5-43 user termination/PRI 5-46 user termination/RBS 5-48 RBS 5-32 Quad T1/PRI 5-43, 5-48 RCV 5-26 real time clock 5-16 rear panel 2-2 reboot system 5-22 receive level 5-26 red alarm 5-25 red CSU LED 3-4 red module status LED 3-4 refresh screen 10-4...
  • Page 161 slot/port user termination 5-37 slt 5-23 SNMP 5-14 access 5-14 communities 5-14 IP address 5-15 privileges 5-15 software rev 4-7 solid green system LED 3-3 solid red system LED 3-3 sort to/from 5-29 source ID 5-34, 5-37, 5-43, 5-45, 5-47, 5-49 speech accept 5-35, 5-38 reject 5-36, 5-39...
  • Page 162 Index log out of a session 5-6 menu path 5-2, 5-4 moving around in 5-2 navigating 5-2 navigating with the keyboard keys 5-5 navigation help 5-4 operating 3-5 operation 5-1 paste items from clipboard 5-6 port status 5-4 refresh the screen 5-6 restore factory default settings 5-6 right pane 5-4 right pane notation 5-5...
  • Page 163 Octal BRI 5-51 Quad T1/PRI 5-46, 5-48 terminations 5-36 users logged into system, number of 5-18 using terminal menu 5-2 using front panel 3-5 util menu 4-6 utilities 10-1 utility Telnet 10-1 TFTP 10-1 TFTP server 10-4 VT 100 10-1, 10-3 utility menu 4-6 video conferencing setup with dial plan 7-2...
  • Page 164 Index PLUS Index-12 ATLAS 800 User Manual 61200226L1-1A...

  • Page 165: Product Support Information

    Technical Support Repair and Return If ADTRAN Technical Support determines that a repair is needed, Technical Support will coordinate with the Custom and Product Service (CAPS) department to issue an RMA number. For information regarding equipment currently in house or possible fees associ-...

Table of Contents