Advertisement
Quick Links
®
Panel Worksurface
with Pedestal to the Floor
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2004 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Panel Worksurface
with Suspended Pedestal
and Aprons
Panel Worksurface
with Suspended Pedestal
Without Aprons
NOTE: For suspended pedestals manufactured after
Feb 2004, see assembly direction 939503249.
NOTE: For floor-supported pedestals manufactured
after Feb 2004, see assembly direction 939503252.
®
Avenir
Panel Worksurface
1/2" & 3/8" Sockets
7/32" Drill Bit
Page 1 of 18
939501051 Rev G
Advertisement
Related Manuals for Steelcase Avenir Panel Worksurface with Suspended Pedestal and Aprons
Summary of Contents for Steelcase Avenir Panel Worksurface with Suspended Pedestal and Aprons
- Page 1 7/32" Drill Bit Panel Worksurface with Pedestal to the Floor If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at Panel Worksurface 888.STEELCASE (888.783.3522) with Suspended Pedestal for immediate action by people who want to help you.
-
Page 2: Table Of Contents
TABLE OF CONTENTS • Panel Worksurface with Hanging Pedestal----------------- 3-9 • Panel Worksurface with Down-to-Floor Pedestal--------- 10-12 • Installing a Curved Worksurface------------------------------ 13 • Installing a Curved Corner Worksurface-------------------- 14 • Pedestal Glide Adjustment------------------------------------- 15-16 • Suspended Pedestal Worksurface Mounted---------------17-20 Items listed below are for identification purposes only and your assembly package will contain only the necessary items for your model installation. -
Page 3: Panel Worksurface With Hanging Pedestal
Panel Worksurface with Hanging Pedestal Height To Top Of Support Surface Recommended Worksurface Height Refer to worksurface height chart below and select Typing Height------------------ 26 3/8" 25 1/8" a desired height for your worksurface. Scribe a pencil mark on the side of panel upright to indicate Typing Height------------------ 27 3/8"... - Page 4 PENCIL MARK PENCIL MARK ON PANEL PENCIL MARK ON PANEL UPRIGHT ON PANEL UPRIGHT UPRIGHT RETAINER LOCK LOCK FINGER HOLE MUST BE AT REAR OF SLOT View from circle #1 on Page 3 View from circle #2 on Page 3 View from circle #3 on Page 3 PENCIL MARK PENCIL MARK...
- Page 5 Remove front and rear aprons (Items 21 and 25) from one of the pedestal drawers. Next insert tab on front apron (Item 25) into slot on rear apron (Item 21). Now align front and rear apron mounting holes with pre-drilled holes in bottom of worksurface.
- Page 6 Remove front and rear aprons (Items 20 and 25) from one of the pedestal drawers. Next insert tab on front apron(Item 25) into slot on rear apron (Item 20). Now align front and rear mounting holes with pre-drilled holes in bottom of worksurface. Next secure aprons to worksurface with (4) screws (Item 7).
- Page 7 End filler (item 13) is used when support assemblies (items 3 and 4) are used. Prior to installing a pedestal next to a moveable wall, an end filler (item 13) must be installed as shown in fig. L with (1) screw (item 11). After pedestal has been installed per step 9, drill a 1/8"...
- Page 8 IMPORTANT: When removing file drawers from pedestal, the cradle assembly must be removed with the drawer at the same time. Store drawer on the front face to prevent grease damage on carpet etc. To re-install, file drawer must be seated into the cradle assembly then re-installed into pedestal. This is done to insure proper drawer alignment and ease of operation.
- Page 9 A. Slide the rear upper flange of pedestal (Item 14) onto tabs on rear mounting bracket (Item 10). B. Secure the front of pedestal to the front mounting bracket (Item 8) with (2) machine screws (Item 16). Refer to Fig.R. C.
-
Page 10: Panel Worksurface With Down-To-Floor Pedestal
Panel Worksurface with Down-to-Floor Pedestals 1/8” Dia. Refer back to pages 3 and 4 of 1/8” Dia. these directions and complete 7/32” Dia. step 1 to install the desired support assembly on movable wall assembly. Use the standar ddesk height (29-3/8") when install- ing the support assembly onto the movable wall assembly. - Page 11 Insert hex head screw (item 27) into 7/32" dia. hole drilled in step 2 Fig U of this section. This screw has a hole thru its shaft. the screw must be turned in so the bottom of screw head is within 1/4" of the worksurface.
- Page 12 4” Turn pedestal attached to worksurface upright. Lay worksurface end opposite pedestal onto support assembly that was installed in step 1 on page 3 of these directions. Refer to fig. X. Fig W Fig X Channel Installation. Warning: DO NOT lift or reposition pedestal by use of channel.
- Page 13 NOTE: "File drawer must be closed then fully extended when re-installing, to seat internal components. This will insure smooth operation". With the pedestal end of worksurface (item 6) slightly pulled back from moveable wall as shown in fig. Y. Insert "T" portion of connector cable into panel slot that is the same height as the top of pedestal...
-
Page 14: Installing A Curved Worksurface
Pedestal Glide Adjustment Installing a Curved Worksurface The curved worksurface is equipped with (2) factory attaching plates. Place curved worksurface onto cantilevered of floor support. Loosen screws slightly to allow attaching plate adjustment. Align slotted holes with holes in cantilevered or floor support. Now position straight worksurfaces on top of attaching plates while at the same time aligning attaching holes. -
Page 15: Installing A Curved Corner Worksurface
CURVED CORNER WORKSURFACE Installing a curved corner worksurface between (2) parent worksurfaces 90 degrees to each other. LEFT HAND RIGHT HAND PARENT PARENT WORKSURFACE WORKSURFACE Fig A Pedestal Glide Adjustment SHARED 18” CANTILEVERED SUPPORT BRACKET RETAINER PLATE SHARED 24” CANTILEVERED SUPPORT BRACKET Fig B Page 15 of 18... - Page 16 1” Assemble parent worksurfaces and cantilevered supports to moveable wall system, in the same manner shown on pages 4 and 8. RETAINER PLATE RETAINER PLATE Position curved corner worksurface onto shared support brackets as shown. Insert (2) no. 12 x 7/8" screws into locating holes thru the shared support brackets as shown in the view in direction of arrow A.
- Page 17 Suspended Pedestal Without Aprons Worksurface Mounted Warning: Do not lift or reposition pedestal by use of channel. Channel will not support the stress. Drawer Removal Note: Before starting Assembly of Pedestal and Desk Remove All Drawers From Pedestal. Marking And Drilling Hole Locations.
- Page 18 NOTE: Position and stick caution label onto kneespace side of pedestal below wire access. Install (4) spacers in pedestal mounting holes, position spacer sand tap to secure with hammer as shown. Underside Of Worksurface Attach pedestal to worksurface. Position pedestal flush to back and side of top.
Need help?
Do you have a question about the Avenir Panel Worksurface with Suspended Pedestal and Aprons and is the answer not in the manual?
Questions and answers