Agilent Technologies J2300D System Manual page 4

Certification
Agilent Technologies certifies that this
product met its published specifications at
the time of shipment from the factory.
Agilent Technologies further certifies that
its calibration measurements are traceable
to the United States National Institute of
Standards and Technology (formerly
National Bureau of Standards), to the extent
allowed by that organization's calibration
facility, and to the calibration facilities of
other International Standards Organization
members.
Restricted Rights Legend
If Software is for use in the performance of
a U.S. Government prime contract or
subcontract, Software is delivered and
licensed as ìCommercial computer
softwareî as defined in DFAR 252.227-7014
(June 1995), or as a ìcommercial itemî as
defined in FAR 2.101(a) or as ìRestricted
computer softwareî as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Agilent Technologiesí standard
commercial license terms, and non-DOD
Departments and Agencies of the U.S.
Government will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S.
Government users will receive no greater
than Limited Rights as defined in FAR
52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995), as
applicable in any technical data.
Before you use this instrument, read the
"General Safety Precautions" and
"Additional Safety Information" sections.
Failure to comply with the precautions or
with specific warnings in this book violates
safety standards of design, manufacture,
and intended use of this instrument. Agilent
Technologies assumes no liability for the
customer's failure to comply with these
requirements.
Advisor Mainframe Features System Guide
General Safety Precautions
The following warnings and operating
information are shown in English followed
by the French translation.
WARNING This product is a Safety Class I
instrument with a protective earth terminal.
WARNING For protection from electric
shock hazard, power cord ground must not
be defeated.
Operating Restrictions
The following general safety precautions
must be observed during all phases of
operation, service, and repair of this
instrument. Failure to comply with these
precautions with specific warnings in this
manual violate safety standards of design,
manufacture, and intended use of this
instrument.
Grounding
To minimize shock hazard, the instrument
chassis and cabinet must be connected to
an electrical ground. The instrument is
equipped with a three-conductor AC power
cable compatible with an approved
three-contact electrical outlet. The power
jack and mating plug of the power cord
must meet International Electrotechnical
Commission (IEC) safety standards.
Environment
Do not operate the instrument in the
presence of flammable gases or fumes.
Operation of any electrical instrument in
such an environment constitutes a definite
safety hazard.
Service and Adjustment
Dangerous voltages exist within this
instrument. Service and adjustment of this
instrument is to be performed only by
trained service personnel.
Do not replace components with the power
cable connected. Dangerous voltages may
be present even when the power cable is
disconnected.
Do not perform internal servicing or
adjustment unless another person, capable
of rendering first aid and resuscitation is
present.
Hazardous Material
Should the LCD be damaged the liquid
crystal material can leak. Avoid all contact
with this material, especially swallowing.
Use soap and water to thoroughly wash all
skin and clothing contaminated with the
liquid crystal material.
Unauthorized Service
The installation of substitute parts or the
installation of any instrument modification
not authorized by Agilent Technologies is
specifically forbidden. The performance of
such unauthorized service can negate the
instrument warranty or any maintenance
agreements.
Return the instrument to an Agilent Sales
and Service Office for authorized service
and repair.
MISE ENGARDE Cet appareil répond aux
normes de la «Classe de sécurité I» et est
muni d'un fil de mise à la terre pour votre
protection.
MISE ENGARDE Pour prévenir les risques
de choc électrique, la broche de mise à la
terre du cordon d'alimentation ne doit pas
être désactivée.
Restrictions d'utilisation
L'utilisateur se doit d'observer les mesures
de précaution énumérées ci-dessous pour
toutes les phases d'utilisation, de service et
de réparation de cet appareil. Le fait de ne
pas s'y conformer équivaut à ne pas
respecter les mises en gardes spécifiques
contenues dans ce manuel et constitue une
3