Page 1
HISTORY INFORMATION FOR THE FOLLOWING MANUAL: MIX5-AGA SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KF-E42A10 RM-YA003 CND/MEXICO KF-E50A10 RM-YA003 CND/MEXICO ORIGINAL MANUAL ISSUE DATE: 11/2005 REVISION DATE SUBJECT 11/2005 No revisions or updates are applicable at this time. LCD PROJECTION TELEVISION...
Page 2
Self Diagnosis Supported model MIX5-AGA SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KF-E42A10 RM-YA003 CND/MEXICO KF-E50A10 RM-YA003 CND/MEXICO KF-E42A10 RM-YA003 LCD PROJECTION TELEVISION 9-965-991-01...
WEGA, Grand WEGA, WEGA GATE, Steady Sound, Inc. Digital Reality Creation, CineMotion, PlayStation, and BN Smoother are trademarks of Sony Corporation. WEGA, Grand WEGA, WEGA GATE, Steady Sound, Digital Reality Creation and CineMotion Macintosh is a trademark licensed to Apple Computer, In are registered trademarks of Sony Corporation.
Page 5
Television system American TV standard, NTSC Channel coverage Terrestrial 2-69/ Cable TV: 2-125 (analog) Screen Size (measured diagonally) 42 inches (KF-E42A10 Only) 50 inches (KF-E50A10 Only) Antenna 75-ohm external antenna terminal for VHF/UHF Projection System 3 LCD Panels, 1 lens projection system LCD Panel 0.73 inch TFT LCD panel...
Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi...
KF-E42A10/E50A10 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KF-E42A10/E50A10 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the POWER/STANDBY will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the POWER/STANDBY fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 9
KF-E42A10/E50A10 DISPLAY OF POWER/STANDBY OR LAMP LED FLASH COUNT Screen PUSH OPEN TIMER LAMP POWER/STANDBY POWER Indicators - One flash is not us ed for self-diag nosis. Example LED OFF Diagnosis Number of times LED Flash 3.0 sec Lamp cove r...
Page 10
KF-E42A10/E50A10 VIEWING THE SELF-DIAGNOSTIC ERRORS The TV MICRO service menu contains a Log category that stores the errors. To view the fi rst error detected, display the SHUTDOWN_LOG1 Adjustment Item of the STATUS category. If other errors are detected, they are stored in the SHUTDOWN_LOG2 Adjustment Item of the STATUS category.
Page 12
KF-E42A10/E50A10 SELF-DIAGNOSTIC BLOCK DIAGRAM AGA board Fan1 IC8002 S2 board TV Micro-computer Fan2 IC7180 Temp. Fan3 IIC-TV Sensor Fan4 FAN-ERR HB board CN8002 IC7021 IIC-TV Temp. +12V LB-ERR Sensor K board B board Audio SP_PROT Amp. BE-OVP B_12V IC4100 BE Micro-computer...
Page 13
KF-E42A10/E50A10 READING LAMP AND PANEL TIME RESETTING THE LAMP TIME The BE_Micro menu of the Service Menu displays the current lamp and When replacing the lamp, use the following to reset the lamp time. panel time of a set. 1. If the Self-Diagnostic screen is already displayed, proceed to step 4.
KF-E42A10/E50A10 SECTION 1: DISASSEMBLY 1-1. OVERVIEW Note: Please refer to the Wire Dressing section of this manual for detailed instructions on reassembling the TV TOOLS NEEDED Long Phillips Screwdriver Needle Nose Pliers Small Flathead Screwdriver or Jewelers Screwdriver The connectors in the MIX5 chassis have been redesigned to ensure they are securely fasten to the boards. Please review the illustrations below.
KF-E42A10/E50A10 1-2. REAR COVER REMOVAL E42A10 1 Pull down the claw Lamp door E50A10 When reassembling the rear cover, be sure to securely lock the lamp door to avoid a lamp cover failure warning. Lamp door 1 Place the lamp door on and turn the handle to close.
KF-E42A10/E50A10 1-3. SERVICE POSITION 2 Screws (+BVTP 4x16) 1 1 screw +PSW M3X8 Remove cable from purse lock Release Power Cord 7 Remove Left Stay Push up on clip to Detach 20x50mm Himelon tape release the Terminal bracket 4 screws (+BVTP 3x12)
KF-E42A10/E50A10 1-9. B BLOCK ASSEMBLY AND RF CABLE REMOVAL 5 Screws (+BVTP 4x16) Remove washer nut 2 Remove RF cable Detach 25x65 conductive tape Detach RF cable 6 Remove cables NOTE: Tape can be reused from wire holder (PN 2-653-955-01) The B Block slides into the bottom board by placing the Block Adjuster Assembly into grooves in the bottom board.
Page 20
KF-E42A10/E50A10 5 Screws +PSW M3X8 NOTE: Hold copper plate when removing the screw 1 Screws +PSW M3X8 3 6 Screws +PSW M3X8 Lift to remove bracket Lift to remove TA Board KF-E42A10/E50A10...
KF-E42A10/E50A10 1-9-1. B BLOCK FAN REMOVAL Be sure to replace D.C. Fan the fan grommets (PN 1-787-333-11) when replacing the fan 6 3 Screws +PSW M3X8 1-9-2. B BOARD REMOVAL B Board shield B Board 4 Screws +PSW M3X8 2 connectors 1-9-3.
KF-E42A10/E50A10 1-10. MAIN FAN REMOVAL 2 screws +BVTP 4x16 Gently pull out Fan, D.C. (PN 1-787-373-11) Be sure fan grommets are in place Release wires Remove when reinstalling the fan from wire holder ground wire KF-E42A10/E50A10...
KF-E42A10/E50A10 1-11. T1 BOARD AND S2 BOARD REMOVAL Note: Remove the Lamp door and Lamp before removing the T1 Board or the S2 Board (See “Replacing the Lamp” in the Appendix section of this service manual.) Remove tape to release...
KF-E42A10/E50A10 1-12. LAMP DRIVER AND OPTICS UNIT BLOCK ASSEMBLY REMOVAL Note: Remove the Lamp door and Lamp before removing the T1 Board or the S2 Board (See “Replacing the Lamp” in the Appendix section of this service manual.) Be careful not...
KF-E42A10/E50A10 1-12-1. OPTICS UNIT BLOCK ASSEMBLY REMOVAL Note: LVDS Cable and Iris are not included with the Optical Block Assembly Note: Fan cable is included in assembly 1-12-2. LAMP DRIVER FAN REMOVAL Note position of wires Push down then Screw...
KF-E42A10/E50A10 1-15. SCREEN FRAME ASSEBMLY AND SPEAKER REMOVAL CAUTION: When removing the Screen Frame Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles. Detach tape to release cables Speaker Speaker 2 Screws (+BVTP 4x13)
KF-E42A10/E50A10 1-16. MIRROR ASSEMBLY REMOVAL CAUTION: When removing the Mirror Cover Assembly be sure to clean the Mirror and Diffusion Plate(s) to remove any dust particles. 4 screws (+BVTP 4x16) Remove top brackets Slide mirror out of brackets 1-17. MIRROR COVER ASSEMBLY REMOVAL...
KF-E42A10/E50A10 WIRE DRESSING BALLAST D.C. POWER CABLE ROUTING (1 OF 2) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control Route Cables along top of duct cover. At the end of the duct, make...
Page 31
KF-E42A10/E50A10 BALLAST D.C. POWER CABLE ROUTING (2 OF 2) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Electro Maagnetic Interference (EMI) Apply 20x50mm himelon tape (p/n:4-079-129-21) to corner of Optical Block.
Page 32
KF-E42A10/E50A10 B BLOCK ASSEMBLY INSTALLATION (1 OF 5) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Install 20x50mm himelon tape over 20P Connector Assy. On AGA board. routing for minimizing Dress 15P Cable from B-Block (p/n:1-910-021-64).
Page 33
KF-E42A10/E50A10 B BLOCK ASSEMBLY INSTALLATION (2 OF 5) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Install 11P (p/n:1-910-021-68) and black cable from Install 20P Connector Assembly (p/n:1-910-015-28) on B-Block side.
Page 34
KF-E42A10/E50A10 B BLOCK ASSEMBLY INSTALLATION (3 OF 5) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Electro Maagnetic Interference (EMI) Install Pin-Plug Cable (from RF Bracket Assembly).
Page 35
KF-E42A10/E50A10 B BLOCK ASSEMBLY INSTALLATION (4 OF 5) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Connect B-Block Fan connector to CN8002 Pig-tail connector on the AGA -Bd.
Page 36
KF-E42A10/E50A10 B BLOCK ASSEMBLY INSTALLATION (5 OF 5) Tool / Torque Philips screwdriver -[4x16mm screw] - 13kg*cm +-1.0kg*cm Caution Points Make sure the back side of the B-Block is clear of pinch-points for cables before applying screws. Apply 4x16mm screws to fix B-Block to Bottom Cabinet [4 places].
Page 37
KF-E42A10/E50A10 B BLOCK ASSEMBLY (1 OF 5) Tool / Torque -Phillips Screw Driver - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It Install D.C. Fan (p/n:1-787-333-11), 3x8mm screw CAUTION: Make sure direction of fan is installed correctly. You should be...
Page 38
KF-E42A10/E50A10 B BLOCK ASSEMBLY (2 OF 5) Tool / Torque -Phillips Screw Driver - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It Install B-Bd shield and B-Bd in DM Sheet Shield. Apply 3x8mm screws (4 Install thermal pads on B-Bd shield plate (p/n:2-632-927-02).
Page 39
KF-E42A10/E50A10 B BLOCK ASSEMBLY (3 OF 5) Tool / Torque -Phillips Screw Driver - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It Install FFC Guard over FFC Cables (p/n:2-652-122-01) is important to control Install 15P Connector Assy. 1-910-021-64 on CN5701. Dress wires in coated CAUTION: Make sure FFC Guard “snaps”...
Page 40
KF-E42A10/E50A10 B BLOCK ASSEMBLY (4 OF 5) Tool / Torque -Phillips Screw Driver - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control Install Optical Unit Bracket, retention screw. Fix Install complete digital sub-unit into Digital Shield case.
Page 41
KF-E42A10/E50A10 B BLOCK ASSEMBLY (5 OF 5) Tool / Torque -Phillips Screw Driver - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control Install Final 3x8mm screw in bottom of B-Block. VARIATION of wire...
Page 42
KF-E42A10/E50A10 C SHIELD ASSEMBLY (1 OF 3) Tool / Torque -Phillips Screw Driver -All screws 5kg-cm +-0.5kg-cm Caution Points Install conductive Tape onto lower C-shield. Fold excess tape over metal tab. Gasket tape must not hang over metal (tape p/n: 2-655-492-31) tab (short circuit can happen).
Page 43
KF-E42A10/E50A10 C SHIELD ASSEMBLY (2 OF 3) Tool / Torque -Phillips Screw Driver -All screws 5kg-cm +-0.5kg-cm Caution Points Apply x2 3x8mm screws on side of C-Shield assembly. Install upper C-Shield case. Apply x2 3x8mm screws. P/n: 2-580-593-01[2 places] P/n: 2-580-593-01[2 places] Install 3x8mm screw over LVDS Connector.
Page 44
KF-E42A10/E50A10 C SHIELD ASSEMBLY (3 OF 3) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Install 20x40 himelon on LVDS connector [2 places]. Electro Maagnetic Apply 20x50mm himelon tape over looped cable.
Page 45
KF-E42A10/E50A10 CHASSIS ASSEMBLY (1 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-0.5kg-cm -[3x8mm] - 5kg-cm +-0.5kg-cm Caution Points Install AGU Shield (p/n:2-645-526-02) with reverse locks (p/n:4-100-521-01) Install GTA-Bd on G Bracket (p/n:2-593-078-31). Apply [3 places] on B-Side of AGA PWB.
Page 46
KF-E42A10/E50A10 CHASSIS ASSEMBLY (2 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-0.5kg-cm -[3x8mm] - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Install Shield covers (p/n:2-596-915-01; 2-596-915-11) on AGA-Bd.
Page 47
KF-E42A10/E50A10 CHASSIS ASSEMBLY (3 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-0.5kg-cm -[3x8mm] - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Electro Maagnetic Interference (EMI) Install Conn.
Page 48
KF-E42A10/E50A10 K BOARD ASSEMBLY Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Install K-Bd into K-Bracket (p/n:2-593-079-11). Fix K-Bd with 3x12mm screw(p/n:7-685-648-79) [2 places]. Install Conn. Assy. 1-910-015-19 in CN3002. Apply 11mm purselock (p/n:4-049-281-01) and one loop to cable (as shown).
Page 49
KF-E42A10/E50A10 LIGHTNING GROUND INSTALLATION (1 OF 4) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Apply 20x50mm himelon tape to secure wires on Optical Block. Position Lightning ground wire (p/n:1-910-015-17).
Page 50
KF-E42A10/E50A10 LIGHTNING GROUND INSTALLATION (2 OF 4) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Install Clamp-On Ferrite core (p/n:1-543-830-011; TDK ZCAT2032-0930) routing for minimizing Route all lightning ground wires behind support brace, and around duct.
Page 51
KF-E42A10/E50A10 LIGHTNING GROUND INSTALLATION (3 OF 4) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Electro Maagnetic Interference (EMI) Install Faston Tabs in F-Pin Terminal Bracket. Any one of the three terminals on the bracket can be used.
Page 52
KF-E42A10/E50A10 LIGHTNING GROUND INSTALLATION (4 OF 4) Tool / Torque Caution Points Apply 20x50mm himelon tape to cables above Lamp Door. Application of tape keeps wires from moving and potentially pinching between rear cover and duct assembly. Tape p/n:4-079-129-21 KF-E42A10/E50A10...
Page 53
KF-E42A10/E50A10 LOWER MAIN HARNESS INSTALLATION (1 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Use split in Lower Harness ( 5-1 on diagram) as a reference to...
Page 54
KF-E42A10/E50A10 LOWER MAIN HARNESS INSTALLATION (2 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control Route all cables through the “C” cut-out in the duct cover. The 11mm...
Page 55
KF-E42A10/E50A10 LOWER MAIN HARNESS INSTALLATION (3 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Apply one loop around cable above ferrite core with C-shield M3 Clamp. Reason is to hold ferrite core steady during transportation (prevents excessive movement).
Page 56
KF-E42A10/E50A10 OVERALL ASSEMBLY (1 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-0.5kg-cm -[4x16mm] - 13kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Dress Wires from Speaker, Speaker Grill and Side inputs in purselocks as Install M3 Clamp and 3x12mm screw on optical block.
Page 57
KF-E42A10/E50A10 OVERALL ASSEMBLY (2 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-0.5kg-cm -[3x8mm] - 5kg-cm +-0.5kg-cm Caution Points Please Follow All CAUTION points listed. It is important to control CAUTION: Make sure Clamp-on Ferrite core is closed/locked. Make sure wires are not pinched in...
Page 58
KF-E42A10/E50A10 OVERALL ASSEMBLY (3 OF 3) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Connect S-Master Connector (p/n:1-910-015-30) to Electro Maagnetic Connect IRIS connector (from front of Optical Block) in AGA-Bd AGA-Bd CN8001 (15P).
Page 59
KF-E42A10/E50A10 RF TERMINAL ASSEMBLY Tool / Torque -3/8” (11mm) Hex Driver - 7kg-cm +-1.0kg-cm Caution Points Do Not Bend metal RF Bracket when installing Hex nut on F-Pin Cable. Bending RF Bracket will cause mis-alignment with rear cover. It will make installation of rear cover difficult.
Page 60
KF-E42A10/E50A10 SPEAKER GRILL ASSEMBLY (1 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It Install Conn. Assy. 1-910-021-67 on HB-Bd. Route wire is important to control Install Latch (p/n:4-088-589-11) on slotted boss with 3x12mm screw.
Page 61
KF-E42A10/E50A10 SPEAKER GRILL ASSEMBLY (2 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It Install 20x50mm Himelon tape (p/n:4-079-129-21) as shown. Position Ferrite core with one loop on 1-910-021-67 over himelon tape.
Page 62
KF-E42A10/E50A10 SPEAKER GRILL ASSEMBLY (3 OF 3) Tool / Torque -Phillips Screw Driver -[3x12mm] - 7kg-cm +-1.0kg-cm Caution Points Please Follow All CAUTION points listed. It Install Latch (p/n:4-088-589-11) with 3x12mm screw (p/n:7-685-648-79) on the Install Latch (p/n:4-088-589-11) with 3x12mm screw (p/n:7- opposite side of the ferrite core (next to wire guide).
Page 63
KF-E42A10/E50A10 TERMINAL ASSEMBLY (1 OF 2) Tool / Torque -Phillips Screw Driver Install Terminal shield (p/n:2-596-920-01) -[4x16mm] Install HPC Assy. Use 4x16mm screw to fix HPC Assy. Use M4 Clamp on one screw -13kg-cm +-1.0kg-cm Screw p/n: 2-580-640-01 M4 Clamp p/n: 2-594-861-01 Install Conn.
Page 64
KF-E42A10/E50A10 TERMINAL ASSEMBLY (2 OF 2) Tool / Torque -Phillips Screw Driver -[3x12mm] -7kg-cm +-1.0kg-cm Caution Points Install Connector Cap (p/n:2-593-083-01) and 3x12mm screw(p/n:7-685- Install purselock (p/n:4-077-726-10); M3 clamp (p/n:2- 648-79). 594-860-01) and 3x12mm screw(p/n:7-685-648-79) CAUTION: BEFORE Installing Terminal Bracket, confirm no cables are in between HDMI and Lower Shield Covers.
Page 65
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (1 OF 6) Tool / Torque Philips screwdriver -[4x16mm screw] - 13kg*cm +-1.0kg*cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Dress M4 wire clamp next to split in upper harness. Keep cable tie to the...
Page 66
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (2 OF 6) Tool / Torque Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Route Ballast Sensor leads(beige connector) inside purselock, route Duct Electro Maagnetic Route Ballast Power Cable (p/n:1-910-015-27) BEHIND the Fan leads (black 3P connector) to the LEFT and into the purselock.
Page 67
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (3 OF 6) Tool / Torque -Phillips Screw Driver -[4x16mm screw] -13kg*cm +-1.0kg*cm Caution Points Please Follow All CAUTION points listed. It is important to control Connect upper main harness leads to lamp fan, and VARIATION of wire Completed Duct block connection.
Page 68
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (4 OF 6) Tool / Torque -Phillips Screw Driver -[4x16mm screw] -13kg*cm +-1.0kg*cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Install 20x50mm himelon tape on top of duct cover. Use circular...
Page 69
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (5 OF 6) Tool / Torque -Phillips Screw Driver -[4x16mm screw] -13kg*cm +-1.0kg*cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire Secure ferrite core over duct block by using two pieces of himelon CAUTION: Please confirm ferrite is closed/locked.
Page 70
KF-E42A10/E50A10 UPPER MAIN HARNESS INSTALLATION (6 OF 6) Tool / Torque -Phillips Screw Driver -[4x16mm screw] -13kg*cm +-1.0kg*cm Caution Points Please Follow All CAUTION points listed. It is important to control VARIATION of wire routing for minimizing Electro Maagnetic Interference (EMI) Upper main harness installed in bottom cabinet.
KF-E42A10/E50A10 SECTION 2: CIRCUIT ADJUSTMENTS 2-1. USING THE REMOTE COMMANDER 2-3. VIEWING THE SERVICE MENUS FOR ELECTRICAL ADJUSTMENTS Use the Remote Commander to view the 3 service menus options. To adjust various set features, use the Remote Commander to put the 1.
KF-E42A10/E50A10 2-4. USING THE REMOTE COMMANDER TO MUTING CHANGE SERVICE DATA MUTING TV/VIDEO POWER TV POWER Writes data DVD/ SAT/ CABLE Use the buttons on the Remote Commander to access the service menu into memory Increase FUNCTION items and adjust the data values.
KF-E42A10/E50A10 SERVICE MENUS 2-4-1. EXITING SERVICE MODE (CATEGORIES ONLY) After completing the changes, exit service mode by turning off the set using the Remote Commander or the power switch. NOTE: After exiting service mode wait 2 minutes before restarting 79 0,&52 *6$,3+ %( 0,&52...
KF-E42A10/E50A10 2-7. H/V CENTER CONFIRMATION AND 2-8. IRIS ADJUSTMENTS ADJUSTMENTS Use the following instructions to adjust the IRIS after replacing either of the following: Use the following instructions to adjust the pictures horizontal and Optical Block Assembly vertical center after replacing either of the following:...
KF-E42A10/E50A10 SECTION 3: DIAGRAMS 3-1. CIRCUIT BOARDS LOCATION The C Board is part of the Optics Unit Block Assembly and cannot be ordered separately Power Supply Block NOTE: The QG Board and the QGA Board are interchangeable. Either board can be used as a replacement 3-2.
Page 76
KF-E42A10/E50A10 REFERENCE INFORMATION Terminal name of semiconductors in silk screen printed circuit ( RESISTOR : RN METAL FILM Circuit Device Printed symbol Terminal name Collector : RC SOLID Transistor : FPRD NONFLAMMABLE CARBON Emitter Base : FUSE NONFLAMMABLE FUSIBLE Collector...
KF-E42A10/E50A10 3-4. SCHEMATICS AND SUPPORTING INFORMATION AGA BOARD SCHEMATIC DIAGRAM (1 OF 3) CN8008 Q8027 TO JIG R8195 2SA1235TP-1EF CN8005 TO HA & HB TO QG BOARD R8125 R8161 CN7000 CN7020 CN7304 CHIP 1/10W 1/10W CN8004 1608 RN-CP RN-CP R8108...
KF-E42A10/E50A10 B BOARD SCHEMATIC DIAGRAM (9 OF 9) C board I/F *CN5400 GH Connector SIDE TYPE L5413 C5463 — 6.3V R5419 2012 1/16W CHIP CM_CLKO LVDSO2_CLK 16V X7R 1005 CLKO C5460 0.01 L5460 LVDSO2_HS CM_HS0 DRAIN(GND) LVDSO2_VS CM_VSO LVDSO2_DE CM_DE0...
Page 92
KF-E42A10/E50A10 [MICRO, MAIN ANALOG CONNECTOR, MAIN DC/DC, SYNC SW, VIDEO A/D CCPX, PC/COMPONENT ADC, DTT/HDMI DIGITAL INPUT, VIDEO PROCESSOR, CHIMERA VIDEO INPUT, CHIMERA 128M DDR SDRAM, LVDS OUTPUT I/F ] [MICRO, MAIN ANALOG CONNECTOR, MAIN DC/DC, SYNC SW, VIDEO A/D CCPX, PC/COMPONENT ADC, DTT/HDMI DIGITAL INPUT, VIDEO PROCESSOR, CHIMERA VIDEO INPUT, CHIMERA 128M DDR SDRAM, LVDS OUTPUT I/F ]...
Page 105
KF-E42A10/E50A10 [PC IN] COMPONENT SIDE CN7202 CN7201 IC7200 PC H PC V PC B PC G PC R D7208 C7204 D7213 D7204 D7205 D7210 JL7204 PS7200 0.4A D7202 D7209 KF-E42A10/E50A10...
Page 106
KF-E42A10/E50A10 [PC IN] CONDUCTOR SIDE J7200 CN7200 EP GW GN 1-867-025-11 (172606311) KF-E42A10/E50A10...
KF-E42A10/E50A10 QG BOARD SCHEMATIC DIAGRAM (2 OF 2) — TO AGA CN8005 1608 FROM DTT (Graphics) C7449 10.5V 1608 C7448 DTGRACKIN CN7304 FB7312 10.5V DTOSD_G7IN 10.5V — R7453 DTOSD_G6IN CHIP JIG_TXD JIG_TXD DTOSD_G5IN JIG_RXD JIG_RXD R7473 SIGN5543 CHIP DTOSD_G4IN GSAIPH_RST...
Page 112
KF-E42A10/E50A10 [GRAPHICS SAIPH, FLASH] COMPONENT SIDE R7320 R7320 RB7310 RB7310 RB7309 RB7309 C7317 C7317 C7320 C7320 C7322 C7322 C7324 C7324 C7327 C7327 c a m 10013 c a m 10013 R7412 R7412 R7318 R7318 R7325 R7325 R7416 R7416 c a m 10040...
KF-E42A10/E50A10 NOTE: The components identifi ed by shading and mark are critical for safety. NOTE: Les composants identifi es per un trame et une marque sont critiques pour Replace only with part number specifi ed. la securite. Ne les remplacer que par une piece portant le numero specifi e.
PURSE LOCK (S) (DIA. 12) A-1123-071-A OPTICS UNIT BLOCK ASSEMBLY When replacing the Optics Unit Block Assembly or the DC Fan be sure to remove any dust particles. (KF-E42A10 ONLY) 1-787-373-11 D.C. FAN The C Board is part of the Optics Unit Block Assembly...
KF-E42A10/E50A10 SECTION 5: ELECTRICAL PARTS LIST NOTE: The components identifi ed by shading Items marked with an asterisk are not stocked since they RESISTORS mark are critical for safety. Replace only are seldom required for routine service. Expect some delay •...
Page 133
KF-E42A10/E50A10 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 136
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES Q8418 8-729-600-22 TRANSISTOR 2SA1235-F R8026 1-216-864-11 SHORT CHIP Q8419 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R8027 1-216-805-11 METAL CHIP 1/10W Q8420 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R8029 1-216-809-11 METAL CHIP 1/10W Q8421...
Page 137
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8071 1-218-871-11 METAL CHIP 0.50% 1/10W R8125 1-216-833-11 METAL CHIP 1/10W R8072 1-218-887-11 METAL CHIP 0.50% 1/10W R8128 1-216-864-11 SHORT CHIP R8073 1-218-883-11 METAL CHIP 0.50% 1/10W...
Page 138
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8209 1-216-833-11 METAL CHIP 1/10W R8259 1-218-863-11 METAL CHIP 4.7K 0.50% 1/10W R8212 1-216-833-11 METAL CHIP 1/10W R8260 1-216-821-11 METAL CHIP 1/10W R8213 1-216-841-11 METAL CHIP 1/10W...
Page 139
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8333 1-216-833-11 METAL CHIP 1/10W R8405 1-216-853-11 METAL CHIP 470K 1/10W R8334 1-216-845-11 METAL CHIP 100K 1/10W R8406 1-216-853-11 METAL CHIP 470K 1/10W R8336 1-216-845-11 METAL CHIP...
Page 140
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8467 1-216-815-11 METAL CHIP 1/10W R8526 1-216-864-11 SHORT CHIP R8468 1-216-815-11 METAL CHIP 1/10W R8527 1-216-864-11 SHORT CHIP R8469 1-216-815-11 METAL CHIP 1/10W R8529 1-216-864-11 SHORT CHIP...
Page 141
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8720 1-218-887-11 METAL CHIP 0.50% 1/10W R8780 1-216-833-11 METAL CHIP 1/10W R8721 1-218-903-11 METAL CHIP 220K 0.50% 1/10W R8781 1-216-833-11 METAL CHIP 1/10W R8722 1-218-887-11 METAL CHIP 0.50% 1/10W...
Page 142
KF-E42A10/E50A10 AGA B NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 160
KF-E42A10/E50A10 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 161
KF-E42A10/E50A10 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 162
KF-E42A10/E50A10 GTA HA HB NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 175
KF-E42A10/E50A10 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Page 176
KF-E42A10/E50A10 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R7516 1-216-809-11 METAL CHIP 1/10W R7579 1-216-805-11 METAL CHIP 1/10W R7517 1-216-864-11 SHORT CHIP R7591 1-216-817-11 METAL CHIP 1/10W R7519 1-216-864-11 SHORT CHIP R7592 1-216-833-11 METAL CHIP...
Page 177
KF-E42A10/E50A10 QGA S2 T1 T2 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R7675 1-216-805-11 METAL CHIP 1/10W R7676 1-216-805-11 METAL CHIP 1/10W R7677 1-216-805-11 METAL CHIP 1/10W R7678 1-216-805-11 METAL CHIP 1/10W R7679 1-216-805-11 METAL CHIP...
Page 178
KF-E42A10/E50A10 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les mark are critical for safety. Replace only remplacer que par une piece portant le numero specifi e.
Electric appliances can cause fire or high temperature, resulting in injury or death. Be sure to follow the instructions below. ❑ Use a Sony XL-2400 replacement lamp (not supplied) for replacement. Use of any other lamp may damage the TV. ❑...
Page 181
KF-E42A10/E50A10 Other Information Remove the outside lamp cover. Remove the lamp door. Turn the knob counterclockwise to OPEN and pull out the cover. Lamp door Pull out the lamp. Hook a finger through the loop of the lamp handle and pull the handle upwards.
Page 182
Turn the knob back to CLOSE and secure the cover. Put the outside lamp cover back in its place. ✍ Consult your Sony dealer for a Sony XL-2400 replacement lamp. ✍ Take great care when replacing the lamp or plugging in/unplugging the connecting cords.
Page 183
KF-E42A10/E50A10 Other Information The used lamp This product contains mercury. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance (http://www.eiae.org). ❑ Do not leave the used lamp near flammable materials or within the reach of children.
Page 184
In an effort to reduce the size of this pdf fi le the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.