Download Print this page

MINOURA DS-2200 Instruction Manual

Bicycle storage stand

Advertisement

Quick Links

Warranty
If you have any questions or need help, you should contact the dealer where you purchased or the Minoura
Contact
distributor in your country first. Only when you cannot get enough service, you can contact us;
MINOURA JAPAN
(for ALL customers)
134-1 Shimomiya, Godo, Anpachi, Gifu 503-2312 Japan
Fax: +81-584-27-7505
Email: minoura@minoura.jp / Web: www.minoura.jp
Bicycle Storage Stand
[Vertical Display Position]
Minoura offers 1-year limited warranty for the first user of this product who purchased it
at brand-new condition. Any other users who get at used condition through shops, auction
site or personal trading cannot recieve this warranty service from Minoura.
For more information, please refer the attached "Minoura Limited Warranty Policy" card.
Made in Japan
DS-2200
Important Notes
DS-2200 is meant to be used with a standard
bicycle only. Never attempt to get on your bike
when it is in the stand.
Place DS-2200 on flat and level floor.
Balance the bike to prevent it from falling down,
especially when using DS-2200 in vertical position.
DS-2200 uses two swingable holders for your
bike. They move on their own to accommodate any
bicycle DS-2200 is designed to hold.
To get maximum stability, set the tire holder
distance as far apart as possible without the bike
touching the floor. If the bike touches the floor, it
will cause instability in the stand.
To set the bike vertical, you must place the rear
wheel on the tire holders. Do NOT place the bike
upside down.
When placing the bike horizontal, we recommend
to set the rear wheel on the tire holders, not the
front wheel.
If you need to set the front wheel in the holders,
make sure the wheel is straight.
You can set the pillar on either right or left side.
Depending on the room condition, choose the
appropriate side.
Be sure you adjust the pillar length correctly to
place the front wheel hook at the 4 o'clock posiition
of the front wheel. If it's too low, the stability will get
worse, and if it's too high, it will become difficult to
mount the bike on DS-2200.
MINOURA North America
Hayward, Califiornia, U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
instructions manual
(ver.1.0 2019/5)
(for U.S. residents ONLY)

Advertisement

loading

Summary of Contents for MINOURA DS-2200

  • Page 1 Minoura. For more information, please refer the attached "Minoura Limited Warranty Policy" card. If you have any questions or need help, you should contact the dealer where you purchased or the Minoura Contact distributor in your country first.
  • Page 2: How To Assemble

    DS-2200 is packed almost ready to go out of the box. How To Assemble All you need to do is install the Step-Bar and Pillar to the Main Frame. Tool: 4mm Hex Wrench How To Read Bolt Size Diameter Make sure the Main Frame direction first Tire Holder (Fig.
  • Page 3 Switching The Pillar Tool: 10mm Spanner Depending on your room layout or your M6 Flat Washer dominant hand, it could be easier for you to access your bike from left side. If so, replace Front Wheel Hook M6 Nylon Nut the pillar to the right side.
  • Page 4 To achieve maximum stability when the bike is mounted by the front wheel, align the front wheel with the bike frame, not handlebars. Using the handlebars could tilt the bike, causing instability. You can remove the Pillar if you use DS-2200 in horizontal style ONLY. - 4 -...
  • Page 5 Vertical Style Mounting the bike vertically saves the most space. Flip and stand the bike, and push forward. You never need to lift up the bike, just push forward, then the rear wheel will step over the Tire Holder naturally. (Fig.
  • Page 6 Front Wheel Hook Position Front Wheel Hook should be located at 4 o'clock position when viewing from right side. It is the best angle to hook the wheel easily and can hold the bike at maximum stability. (Fig. P) If the hook position is too low for the bike size, the bike may rock back and forth and decrease stability.