Eaton Power Xpert Release PXR 10 Manual page 48

9 Available protection settings
bit mask
Register field field set points name
403008 INCOM CAM baud rate
403009 Ethernet CAM DHCP enable
403010 Ethernet CAM IP addr. MSB
403011 Ethernet CAM IP addr. LSB
403012 Ethernet CAM IP addr. MSB
403013 Ethernet CAM IP addr. LSB
403014 Ethernet CAM subnet mask
403015 Ethernet CAM default gateway
403016 Ethernet CAM default gateway
403017 Ethernet CAM reset pin
403018 Profibus CAM address
Set points group 4: I/O module group
bit mask
Register field field set points name
403000 15-0 0xFFFF Password
403001 15-0 0xFFFF I/O module cfg
403002 15-0 Validity flags 0....15
403003 15-0 Validity flags 16....31
403004 15-0 0: digital output 0
403005 15-0 1: digital output 1
403006 2: digital output 2
403007 3: digital output 3
403008 4: S0 channel 0 type
403009 5: S0 channel 0 scale
403010 6: S0 channel 0 pulse
403011 7: S0 channel 1 type
403012 8: S0 channel 1 scale
403013 9: S0 channel 1 pulse
403014 10: Modbus address
44
PXR tRiP units foR PoweR Defense molDeD case ciRcuit bReakeRs MN012007EN June 2018 www.eaton.com
R/w format Value definition
R 1 <--> 9600bps see IL01301033e
P8 "for series NRX INCOM
communication adapter module,
baud rate is fixed at 9600 baud and
represented by a value of 01"
R 0 <--> false
1 <--> true
R 0~255 <--> 0~255
R 0~255 <--> 0~255
R 0~255 <--> 0~255
R 0~255 <--> 0~255
R 16~32 <--> 16~32
R 0~255 <--> 0~255
R 0~255 <--> 0~255
R 0~255 <--> 0~255
R 1~125 <--> 1~125
R/w format Value definition
W Encoded Default "0000"
R/W Encoded 0x04FF
R/W Encoded For each bit:
0 : corresponding parameter inactive
1 : corresponding parameter active
e.g. Bit 8 = 1
==> parameter 8 = active
R/W Encoded For each bit:
0 : corresponding parameter inactive
1 : corresponding parameter active
e.g. Bit 8 = 1
==> parameter 8 = active
R/W Encoded
R/W Encoded
R/W Encoded
R/W Encoded
R/W 0: output disabled
1: sends pulses based on active energy
2: sends pulses based on reactive energy
3: sends pulses based on apparent energy
R/W 0: sends a pulse every
1: W 1: sends a pulse every 10 W
2: sends a pulse every 100 W
3: sends a pulse every 1000 W
R/W pulse duration x *10 ms
range: 1...50 ==> 10...500 ms
R/W 0: output disabled
1: sends pulses based on active energy
2: sends pulses based on reactive energy
3: sends pulses based on apparent energy
R/W 0: sends a pulse every
1 W 1: sends a pulse every 10 W
2: sends a pulse every 100 W
3: sends a pulse every 1000 W
R/W Pulse duration x *10 ms
Range: 1...50 ==> 10...500 ms
R/W Modbus ID (= device address)
permitted range: 1...255