Table of Contents
Advertisement
Quick Links
ClearSpan
Steel End Frame Kit
™
20' Wide
GROUND LEVEL
Diagram shows the end frame kit without a door. (Door and end panel are purchased separately.)
Rafter is not included with kit. Customer supplies the concrete to secure the vertical tubing.
©2010 ClearSpan™
STK#
All Rights Reserved. Reproduction
R020B00001
is prohibited without permission.
Revision date: 09.30.10
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ClearSpan R020B00001
Summary of Contents for ClearSpan R020B00001
- Page 1 GROUND LEVEL Diagram shows the end frame kit without a door. (Door and end panel are purchased separately.) Rafter is not included with kit. Customer supplies the concrete to secure the vertical tubing. ©2010 ClearSpan™ STK# All Rights Reserved. Reproduction R020B00001 is prohibited without permission.
-
Page 2: Safety Precautions
Please read these instructions BEGIN before you begin. The R020B00001 end frame is attached to the main frame If you have any questions during the assembly, contact after the main building frame is assembled. If you have Customer Service for assistance. -
Page 3: Assembly Procedure
Important Information ASSEMBLY PROCEDURE UNPACK AND IDENTIFY PARTS Following the instructions as presented will help ensure The following steps will ensure that you have all the the proper assembly of your end frame. The steps necessary parts before you begin to assemble the end outlining the assembly process are as follows: frame. -
Page 4: Parts Identification
Parts Identification The following graphics and photos will help identify the different parts. (Some parts are not shown.) FAME09B FA4482B 104773 100441 1/2" Flat Washer Tek Screw 1/2" x 3" GR 325 with Nut Nut Setter 108506 108529 2375S100 Mounting Bracket Hat Channel 2.375"... - Page 5 Overview ClearSpan™ End Frame Kit GROUND LEVEL OVERVIEW This section describes assembling your end frame kit. For ATTENTION: Secure top of each vertical support using details, please see section "Assembling the End Frame Kit the 104773 bolt and nut and the 1/2" flat washers.
- Page 6 End Frame Assembly ASSEMBLING THE END FRAME KIT COMPONENTS Assembled Vertical Supports Consult the end frame diagrams at the back of these instructions before you begin. Assistance is required to assemble the end frame. ATTENTION: These instructions describe the assembly of the 20' wide end frame.
- Page 7 End Frame Assembly END FRAME INSTALLATION (CONTINUED) 3. Align the center of another hat channel section with Assemble the End Frame the on-center marks to complete the horizontal brace. Overlap the previously installed section by a minimum After the vertical supports are attached and the concrete of 4"-6"...
-
Page 8: Outside View
End Frame Assembly END FRAME INSTALLATION (CONTINUED) 6. Attach each end of the two (2) upper horizontal braces to the end rafter using the 108506 mounting brackets and Tek screws as shown below. Position bracket so that a Tek screws can be attached through both lips of the hat channel and into the bracket (6b and 6c). - Page 9 • Replace all worn or damaged parts promptly. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. Revision date: 09.30.10...
- Page 10 Revision date: 09.30.10...
- Page 11 Revision date: 09.30.10...
- Page 12 Revision date: 09.30.10...
- Page 13 Revision date: 09.30.10...
- Page 14 Revision date: 09.30.10...
- Page 15 Revision date: 09.30.10...
- Page 16 Revision date: 09.30.10...
- Page 17 Notes This page is reserved for customer notes. Revision date: 09.30.10...
Need help?
Do you have a question about the R020B00001 and is the answer not in the manual?
Questions and answers