Table of Contents
Advertisement
Quick Links
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: (800) 253-2363
Telephone: (805) 933-9970
bendpak.com
Turf Maintenance Lift Kit
Quick Start Guide
Document P/N 5900178 — Revision A1 — Released April 2021
The Turf Maintenance Lift Kit is a Lift accessory that adapts BendPak's Two-Post Lift models GP-7
Series, D2-10C, XPR-9TS, XPR-9SBT, XPR-10S Series, XPR-10TS Series, and the XPR-10XLS
Series. The adapter consists an adjustable, full-width Wheel Stop and adjustable left and right Wheel
Forks. One version utilizes a fixed width Wheel Stop for use on the GP-7 series Lift only.
More information about BendPak products, including Two-post Lifts, is available at bendpak.com.
Advertisement
Table of Contents
Related Manuals for BendPak Turf Maintenance Lift Kit
Summary of Contents for BendPak Turf Maintenance Lift Kit
- Page 1 Quick Start Guide Document P/N 5900178 — Revision A1 — Released April 2021 The Turf Maintenance Lift Kit is a Lift accessory that adapts BendPak’s Two-Post Lift models GP-7 Series, D2-10C, XPR-9TS, XPR-9SBT, XPR-10S Series, XPR-10TS Series, and the XPR-10XLS Series.
-
Page 2: Liability Information
Copyright. Copyright © 2021 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes. - Page 3 Turf Kit Slide Receiver Weldment 5210229 5210229 Turf Kit Wheel Fork Weldment 5174068 Turf Kit Parts Bag 5735866 Turf Kit Trough Support Strap 5601404 GP-7 Rear Wheel Stop Weldment 3 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 4 Washer, M12 Flat Washer 5530421 M10 x 40 Hex Head Bolt 5535998 Nut M10 5545200 ø Washer, M10 x 18 Split Lock 5545341 ø Washer, M10 x 20 Flat 4 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
-
Page 5: Weight Restrictions
Make a visual inspection of the Lift and the Turf kit before using it. Do not use the Lift if you find any missing or damaged parts. Instead, take it out of service, then contact an authorized repair facility, your distributor, or BendPak at (805) 933-9970 or by email at support@bendpak.com. thorough •... - Page 6 The following procedure details the steps required to get your Turf Kit setup and running. The GP-7 Two-Post Lift is used as an example throughout this Quick Start Guide. Your specific Lift may look slightly different. The Turf Kit is designed to function with the following BendPak Two-Post Lifts:...
- Page 7 Turf Kit. Store the Lift Arms where they will be out of the way. (GP-7 Lift Head shown. Your actual Lift may appear differently, and use different components.) 7 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 8 5. Remove the Snap Rings and then withdraw the Gear Shaft while holding the Lift Head Springs so they will not be lost. 6. Retain all of the parts you removed to use when your remove the Turf Kit. 8 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 9 8. Move the Turf Kit’s right and left Long Lift Arms (items 2 & 3) next to the right and left Lift Heads. Verify the Arms are oriented as shown in the detail below. 9 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 10 10. Install the Lift Head Closeout Gusset on both Lift Heads. Verify the each Gusset is oriented as shown below and secure each Gusset with four M12 x 25 Hex Head Bolt and M12 Washers (Parts Bag items 5 and 6). 10 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 11 Receivers are oriented as shown in figure below. 12. Slide the Wheel Fork Assembly (item 9) into the Receiver Weldment (item 8) on both left and right sides orient the part as shown below. 11 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 12 Back Wheel Stop out in front of the Long Lift Arms as shown in the figure below and adjust the Steps 14 and 15 inside distance between the carriers to match the Lift Arms as shown below. not required on the fixed width GP-7 Version (5174042). 12 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 13 Trough Support Straps (item 11) on both the front and back of the Rear Wheel Stop set to the distance measured in the previous step. 16. Use a Forklift or an assistant to install the assembled Wheel Stop on the Lift Arms. 13 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
- Page 14 Your Turf Kit is ready to use. If you run into issues with your Turf Kit that you cannot fix, visit www.bendpak.com/support/, email support@bendpak.com, or call (800) 253-2363. 14 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
-
Page 15: Operation
11. If the Vehicle is stable, raise the Lift to the desired height. If the Vehicle is not stable, lower the Lift back to the ground and make any necessary adjustments. 15 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com... - Page 16 5. When the Lift is on the ground, release both Handles, then move the Wheel Forks to their full drive- through positions. 6. Drive the Vehicle out of the Lift. 16 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
-
Page 17: Specifications
Specifications Turf Kit Assembly with Adjustable Wheel Stop (5210262) 17 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com... - Page 18 Turf Kit Assembly with Fixed Rear Wheel Stop (5174042) (GP-7 Only) 18 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
-
Page 19: Maintenance Log
Maintenance Log 19 of 20 Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com... - Page 20 1645 Lemonwood Dr. Santa Paula, CA 93060 USA Copyright © 2021 BendPak Inc. All rights reserved. bendpak.com...
Need help?
Do you have a question about the Turf Maintenance Lift Kit and is the answer not in the manual?
Questions and answers