Odp - Operator Display For Pushbuttons - Siemens 353 User Manual

Function Blocks

3.2.57 ODP - Operator Display for PushButtons

ODP function blocks are one of five operator displays that
can be used on a one per loop basis to configure local
operator display functions as well as network parameters.
See the i|ware PC faceplate example on the next page.
The ODP function block can provide up to 8 groups of
two pushbuttons and one selector switch. Each group
includes:
•
One normally open pushbutton, identified as PB1, on
the local faceplate. It can have a 6-character tag to
identify the button function on a HMI display.
•
One normally closed pushbutton, identified as PB2 on
the local faceplate. It can have a 6-character tag for
display on an HMI.
•
One two-position selector switch identified as A/M on
the local faceplate. It can have a 6-character tag for
switch position identification on an HMI.
Each group also has a set of 6-character messages
associated with the status of a feedback signal (1/0).
Each pushbutton has a configuration parameter that
controls how long the button function will be held in the
pressed position. The default value is 1 second but can be
set from 0.1 (or scan time if greater than 0.1) to 10
seconds.
The LOOP # parameter is used to index reads and writes
to Modbus parameters. See Section 5 for more
information on network parameters.
The VIEW OD parameter, when set to YES enables the
operator display to be viewed and accessed locally. In
cases where it is desired to view display or operation
parameters only from a network workstation, the
parameter should be set to NO.
During a cold or warm start, the A/M switch will power up in the Auto position. During a hot start, the A/M switch
will power up in the position prior to power down.
Each group can be displayed on the local faceplate using the D button. When first stepping into a loop using the
Loop button, the loop tag will be displayed (e.g. PBDisp1). Pressing the D button will scroll through the groups
displaying the group tag (e.g. MS1036) in the alphanumeric and the value of the feedback in the digital display (e.g.
1). The feedback message associated with this feedback value can be viewed on the local faceplate using the
UNITS button. The A/M button will display the position of the group selector switch and enable switching the
group selector switch between auto and manual.
3-58
.
Operator Display for Pushbuttons
ODP_
Operator Display
for
Pushbuttons
11
Input 11
12
Input 12
Group 1
1A
Input 1A
1M
Input 1M
1F
Input 1F
81
Input 81
82
Input 82
Group 8
8A
Input 8A
Input 8M 8M
Input 8F 8F
1 T A G
G
Group 1 TAG
(S)
1 1 T A G
G P
Group 1 PB1 TAG
1 1 H I T
G P
Group 1 PB1 Hold In Time
2 T A G
G 1 P
Group 1 PB2 TAG
1 2 H I T
G P
Group 1 PB2 Hold In Time
G 1 S A T A G
Group 1 Switch Position A TAG
G 1 S M T A G
Group 1 Switch Position M TAG
G 1 F 1 T A G
Group 1 Feedback 1 TAG
G 1 F 0 T A G
Group 1 Feedback 0 TAG
G 8 T` A G
Group 8 TAG
(S)
G 8 P 1 T A G
Group 8 PB1 TAG
G 8 P 1 H I T
Group 8 PB1 Hold In Time
G 8 P 2 T A G
Group 8 PB2 TAG
G 8 P 2 H I T
Group 8 PB2 Hold In Time
G 8 S A T A G
Group 8 Switch Position A TAG
G 8 S M T A G
Group 8 Switch Position M TAG
G 8 F 1 T A G
Group 8 Feedback 1 TAG
G 8 F 0 T A G
Group 8 Feedback 0 TAG
L O O P #
LOOP # ................................................ 01 to 25
(S)
I E W O D
V VIEW Operator Display
I N P U T 1 1
.......................
INPUT 11
(H)
I N P U T 1 2
........................
INPUT 12
(H)
I N P U T 1 A
INPUT 1A .......................
(H)
N P T 1 M
I U
INPUT 1M
(H)
N T 1 F
I P U INPUT 1F .......................
(H)
I N P U T 8 1
.......................
INPUT 81
(H)
I U T 8 2
N P .......................
INPUT 82
(H)
I N P T 8 A
U
INPUT 8A ......................
(H)
N 8
I P U T M
INPUT 8M
(H)
N T 8 F
I P U
INPUT 8F .......................
(H)
UM353-1B
Output 11
11
Output 12
12
Output 13
13
Output 81
81
Output 82
82
Output 83
83
............................... 6 ASCII Char
(Group1)
....................... 6 ASCII Char
(START )
(S)
............. 0.1 - 10 sec (1 sec)
(S)
....................... 6 ASCII Char
(STOP )
(S)
............. 0.1 - 10 sec (1 sec)
(S)
.. 6 ASCII Char
(AUTO )
(S)
.. 6 ASCII Char
(MAN )
(S)
........... 6 ASCII Char
(ON )
(S)
........... 6 ASCII Char
(OFF )
(S)
............................... 6 ASCII Char
(Group8)
....................... 6 ASCII Char
(S) (START )
............. 0.1 - 10 sec (1 sec)
(S)
....................... 6 ASCII Char
(S) (STOP )
............. 0.1 - 10 sec (1 sec)
(S)
.. 6 ASCII Char
(S) (AUTO )
.. 6 ASCII Char
(S) (MAN )
........... 6 ASCII Char
(S) (ON )
........... 6 ASCII Char
(S) (OFF )
(null)
...................... NO/YES YES
(H)
loop tag.block tag.output
(null)
loop tag.block tag.output
(null)
loop tag.block tag.output (null)
......................
loop tag.block tag.output (null)
loop tag.block tag.output
(null)
loop tag.block tag.output
(null)
loop tag.block tag.output (null)
loop tag.block tag.output (null)
......................
loop tag.block tag.output (null)
loop tag.block tag.output (null)
Rev. 3
April 2012