Advertisement
Completing the Installation in
Windows 95
If Windows 95 Is Not Installed on Your PC
If Windows 95 is not already installed on your PC, install
it now and then continue with the instructions in the
next section, If Windows 95 Is Installed on Your PC.
Follow these steps if you need to install Windows 95
from a CD-ROM drive connected to your SlimSCSI
adapter:
1
Insert the SlimSCSI adapter in a PC Card slot, connect
the CD-ROM drive to it, and turn the drive
Be sure the CD-ROM drive is terminated, if it is the last
(or only) SCSI device on the bus. Also, be sure that
you have installed your PC's version of DOS Card
and Socket Services.
2
Boot the PC to DOS and insert the Adaptec EZ-SCSI
diskette #2 in the PC's floppy drive.
3
At the DOS prompt, change to the drive letter of the
floppy drive (usually a:), type dosinst, and press
Enter.
4
Follow the instructions that appear on the screen.
EZ-SCSI will install the drivers required by your
CD-ROM drive.
5
When EZ-SCSI DOS installation is complete, remove
the diskette and reboot your PC. Be sure the
CD-ROM drive is still powered
ON
6
Insert the Windows 95 installation CD in the
CD-ROM drive, and follow the installation instruc-
tions that appear on the screen.
7
When Windows 95 is installed on your PC, continue
with the following section, If Windows 95 Is Installed
on Your PC.
4
If Windows 95 Is Installed on Your PC
1
Start Windows 95 on your PC, if it is not already
running.
2
To ensure that the correct Card and Socket Services
are installed, open the Control Panel and double-click
PC Card (PCMCIA). Then follow the instructions
that appear on the screen.
3
If the SlimSCSI adapter is not already inserted in the
slot, insert it now. If no prompt appears, continue
with step 4.
If a New Hardware Found dialog box appears, select
Driver from disk provided by hardware manufac-
turer and click OK. Then insert the Adaptec EZ-SCSI
diskette #1 in the floppy drive. Select the drive letter
of your floppy drive and click OK, and then follow
ON
.
the instructions that appear on the screen. (This step
ensures that the most up-to-date versions of drivers
are installed.)
4
Insert the Adaptec EZ-SCSI diskette #1 in the floppy
disk drive.
5
Click the Start button and select Run.
6
Type a:\setup and click OK.
7
Follow the instructions that appear on the screen.
8
When Adaptec EZ-SCSI is installed and your PC rec-
ognizes the SlimSCSI adapter, continue with Using the
SlimSCSI Adapter on page 7.
Note:
the SlimSCSI adapter and SCSI devices at this
point, there may be a resource allocation prob-
when you do this.
lem. Follow these steps:
1
Review the Troubleshooting Checklist on page 8.
2
If the SlimSCSI adapter is still not recognized, insert
the CardWizard Pro for Windows 95 diskette in the
floppy disk drive.
3
Type a:\setup and click OK.
4
Follow the directions that appear on the screen.
(Choose the defaults for a "typical" installation.)
If your Windows 95 PC does not recognize
AAAA AAAA
AA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAA
AAA
A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
A A
AA
A
AA AA
A A
AA AA
A A
AA
A
AA AA
A A
AA AA
A A
AA AA
A A
AA
A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
A A
AA
A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
A A
AA
A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
A A
AA AA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAAA
AAAA AAA
AAA
A A
AAAA
Advertisement
