Xylem optimyze Installation, Operation And Maintenance Manual
Hide thumbs
Also See for optimyze:
- Quick start manual (2 pages) ,
- Manual (24 pages) ,
- Quick start manual (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Xylem optimyze
Summary of Contents for Xylem optimyze
- Page 1 Installation, Operation, and Maintenance Manual P2007013_1.0 ™ optimyze...
-
Page 3: Table Of Contents
5.6 Install the flat plate mounting..................12 5.7 Install the sensor......................13 6 Operation........................... 14 6.1 Precautions........................14 6.2 Download the optimyze application................14 6.3 Register the user......................14 6.4 Start the application.....................14 6.5 Activate the sensor...................... 14 6.6 Set up the configuration mode..................15 6.7 Connect a mobile phone to the sensor................15... - Page 4 12.1.3 FCC / IC RF radiation exposure statement............25 12.1.4 UL and cUL listed (E516095)................25 12.2 For EU countries......................25 12.2.1 RF radiation exposure statement................25 12.2.2 WEEE 2012/19/EU Notice.................. 26 13 Declaration of Conformity....................27 13.1 EU Declaration of Conformity..................27 ™ optimyze Installation, Operation, and Maintenance Manual...
-
Page 5: Introduction And Safety
This includes any modification to the equipment or use of parts not provided by Xylem. If there is a question regarding the intended use of the equipment, please contact a Xylem representative before proceeding. -
Page 6: User Safety
WARNING: Do not crush, puncture, short, or expose batteries to a temperature above +85°C (185°F). Only use batteries supplied by Xylem Inc. for replacement. Do not ingest batteries, chemical burn hazard. This product contains two replaceable lithium batteries. Consult the product instruction manual for replacement guidelines. -
Page 7: Spare Parts
CAUTION: Only use the manufacturer’s original spare parts to replace any worn or faulty components. The use of unsuitable spare parts may cause malfunctions, damage, and injuries as well as void the warranty. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 8: Transportation And Storage
The product must be stored in a covered and dry location free from heat, dirt, and vibrations. NOTICE: Protect the product against humidity, heat sources, and mechanical damage. NOTICE: Do not place heavy weights on the packed product. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 9: Product Description
7. Infrared (IR) sensor window 8. Magnetic feet ™ optimyze is a trademark of Xylem, Inc. or one of its subsidiaries. All other trademarks or registered trademarks are property of their respective owners. ® The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xylem Inc is under license. -
Page 10: User Interface
Shows the drop-down list Allows the user to capture or upload photo Blue Allows the user to enable feature Gray Allows the user to disable feature Allows the user to change the language of the application ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 11: Main Menu
Reminders Allows the user to create and view the Notifications must be turned on in the maintenance reminders for a specific settings to create and receive reminders asset ™ optimyze Installation, Operation, and Maintenance Manual... - Page 12 15. following options for the Sensor placed on the part: – NDE Bearing (Non-drive end) – DE Bearing (Drive end) – Motor and Other Documents Shows the product-specific information, literature, and data ™ optimyze Installation, Operation, and Maintenance Manual...
-
Page 13: Installation
• The standard magnetic mounting cannot be installed on special alloys or stainless steels. • Before the sensor is installed, the pump or motor surface must be cleaned. • If there is no correct surface to install the standard magnetic mounting, use the flat plate mounting. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 14: Flat Plate Mounting
13. 5. Install the screws. 6. Use a torque wrench to tighten the screws. The torque must be 0.88 Nm (7.8 lbf.in). 7. Install the flat plate mounting and sensor on the pump. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 15: Install The Sensor
Table 1: Default position Axis Align Position Axially to the shaft Horizontally to the shaft Radially to the shaft Table 2: Alternate positions Table 3: Incorrect position Axis Align Position Not aligned to major vibration axis ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 16: Operation
6.3 Register the user 1. On the landing page, tap the Register button. 2. If the user already has a Xylem cloud account, register by using the existing details. 3. On the Register page, follow these steps. a) Type the following information: –... -
Page 17: Set Up The Configuration Mode
1. Before connecting the mobile phone to sensor, check that the following procedures are completed: 1. Bluetooth wireless technology is enabled. 2. Camera permission is allowed for the optimyze application. 2. On the Asset health page, tap the icon. 3. On the Add a sensor page, select one of the following options:... -
Page 18: Configure The Asset
End suction, Green ≤ 4.9 ≤ 6.2 vertical inline, > 4.9 > 6.2 split case, and horizontal multistage ANSI/HI 9.6.4 Vertical turbine Green ≤ 4.3 ≤ 5.6 and vertical > 4.3 >5.6 multistage ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 19: Maintenance
Gasket must not be reused. 7.1.2 Clean the gasket groove 1. Use a small cotton bud and rubbing alcohol to clean the gasket groove in the lower cover. 2. Repeat this procedure for the upper cover. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 20: Install The Battery
2. Carefully install the upper cover on the lower cover. The outer rim of the cover must surround the lip of the lower cover. The Xylem logo must align with the external power supply connector. 3. Use the T10 screw driver to install the screws on the cover. -
Page 21: Troubleshooting
Activate the sensor on page 2. Battery of the sensor is depleted. 3. If necessary, replace the battery. The optimyze application icon is – Check the application page in not visible on the mobile device. mobile device for the optimyze application icon. - Page 22 2. Hold the magnet along the side wall of the sensor near the The sensor does not turn on after ® Bluetooth icon. the magnet is kept near the ® Bluetooth icon. ™ optimyze Installation, Operation, and Maintenance Manual...
-
Page 23: Technical Specification
-20°C to +135°C (-4°F to +275°F) Measurement method Non-contact infrared temperature sensor Minor gradient accuracy (0°C to 25°C gradient) +/-1°C Moderate gradient accuracy (25°C to 50°C gradient) +/-2°C Large gradient accuracy (50°C to 100°C gradient) +/-4°C ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 24: Vibration Measurement
9.9 Part numbers Part Part number optimyze (standard sensor) P2007000 optimyze battery replacement kit P2007030 optimyze optional flat plate mounting kit P2007031 using default sampling rate at 25°C, one connection for each day ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 25: Product Warranty
EXEMPLARY OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED SAVINGS OR REVENUE, LOSS OF INCOME, LOSS OF BUSINESS, LOSS OF PRODUCTION, LOSS OF OPPORTUNITY OR LOSS OF REPUTATION. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 26: Cybersecurity
11 Cybersecurity 11 Cybersecurity Xylem Product Cybersecurity Xylem values your system security and the availability of your critical services. For more information on Xylem cybersecurity practices or to contact the cybersecurity team please xylem.com/security visit ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 27: Certifications
2. This device must accept any interference received, including interference that may cause undesired operation. 12.1.2 CAN ICES-3 (A)/NMB-3(A) Any changes or modifications not expressly approved by Xylem Inc. Could void the user’s authority to operate this equipment. NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 28: Weee 2012/19/Eu Notice
Therefore, if the user wants to eliminate this device, he or she can contact the producer and follow the system that he uses to allow the selective collection of the device at the end of its life, or independently select an authorized chain for its management. ™ optimyze Installation, Operation, and Maintenance Manual... -
Page 29: Declaration Of Conformity
Fluid Handling LLC, 8200 Austin Avenue, Morton Grove, IL 60053, USA Name and address of the authorized representative Xylem Service Italia S.r.l., Via Vittorio Lombardi 14, 36075 Montecchio Maggiore VI, Italy 3. This declaration of conformity is issued under the sole responsibility of the manufacturer. - Page 32 For more information on how Xylem can help you, go to www.xylem.com Xylem Inc. Visit our Web site for the latest version of this document and more information 8200 N.
Need help?
Do you have a question about the optimyze and is the answer not in the manual?
Questions and answers