Figure 36 - Sample Printout (Setpoint Report) - York YR Manual

FORM 160.81-O1 (1020)
ISSUE DATE 10/05/2020
YORK SETPOINTS
CHILLER ID 0
(c) 1997 – 2001 YORK INTERNATIONAL CORPORATION
Mon 21 Jun 1999 1:27:39 PM
Software Versions
–––––––––––––––––––––––––––––––––––––––––––––––––––––
Controls = C.MLM.05.02.102
BIOS = C.MLM.00.03
Kernel = 0.18 GUI = 0.32
SIO = 0.22
GPIC = 0.05
SSS [Skip if Motor Type is not Serial SSS] = C.SSS.01.01
System Information
–––––––––––––––––––––––––––––––––––––––––––––––––––––
System Language
Data Display Mode
Control Source
Remote Analog Input Range
Clock
Flow Switch
Jumper Settings
–––––––––––––––––––––––––––––––––––––––––––––––––––––
Chilled Liquid Pump Operation
Anti-Recycle
Power Failure Restart
Liquid Type
Motor Type
Printer Setup
–––––––––––––––––––––––––––––––––––––––––––––––––––––
Automatic Printer Logging
Log Start Time
Output Interval
Printer Type
Baud
Data Bits
Parity
Stop Bits
COM 2 Setup
–––––––––––––––––––––––––––––––––––––––––––––––––––––
Baud
Data Bits
Parity
Stop Bits
Evaporator
–––––––––––––––––––––––––––––––––––––––––––––––––––––
Leaving Chilled Local Setpoint
Leaving Chilled ISN Setpoint
Leaving Chilled Modem Setpoint
Leaving Chilled Analog Setpoint
Leaving Chilled Digital Setpoint
Period
Error
Rate
Max Load Pulse

FIGURE 36 - SAMPLE PRINTOUT (SETPOINT REPORT)

JOHNSON CONTROLS
Max Unload Pulse
Remote Range
Restart Offset
Restart Setpoint
Shutdown Offset
Shutdown Setpoint
Brine Low Evaporator Cutout
Ice Storage
Offset
Condenser
––––––––––––––––––––––––––––––––––––––––––––––––––––––
High Pressure Warning Threshold
Drop Leg
Warning
Freeze Time
= English
[Skip the following section if Hot Gas Bypass is not enabled]
= English
= Local
= 0 – 10 Volts
Hot Gas
= Enabled
––––––––––––––––––––––––––––––––––––––––––––––––––––––
= Analog
Hot Gas
Setpoint
On Setpoint
= Standard
Oil Sump
= Enabled
––––––––––––––––––––––––––––––––––––––––––––––––––––––
= Auto
Auto Zero
= Water
= EM
Compressor
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Maximum Load Temperature
Maximum Load FLA
= Disabled
Motor FLA Limit
= 12:00 am
Liquid Injection Threshold
= 60 Min
= Okidata
[Skip the following section if Liquid Level is not enabled] Refrigerant
= 9600 Baud
Level Control
= 8 Bits
––––––––––––––––––––––––––––––––––––––––––––––––––––––
= None
Level Control
= 1 Bit
Setpoint
Valve Preset Time
[Skip the following section if Motor Type is not EM]
= 19200 Baud
Electro-Mechanical Starter
= 8 Bits
––––––––––––––––––––––––––––––––––––––––––––––––––––––
= Odd
Local Motor Current Limit
= 1 Bit
Remote ISN Current Limit
Remote Analog Current Limit
Remote Digital Current Limit
Remote Modem Current Limit
= 45.0 ~F Pulldown Demand Limit
Pulldown Demand Time
= 45.0 ~F
= 45.0 ~F
= 45.0 ~F
[Skip the following section if Motor Type is not Mod A SSS] Liquid-
= 45.0 ~F
Cooled Solid State Starter
= 10 Sec
––––––––––––––––––––––––––––––––––––––––––––––––––––––
= 1.5 ~F
Local Motor Current Limit
= 2.5 ~F/S
Remote ISN Current Limit
= 1.5 Sec
Remote Analog Current Limit
SECTION 4 - PRINTERS
= 1.5 Sec
= 10.0 ~F
= 0.0 ~F
= 45.0 ~F
= 4.0 ~F
= 41.0 ~F
= 25.0 Psig
= Off
= 0
= 44.9 Psig
= Enabled Freeze
= Disabled
= 30 Min
4
= Disabled Off
= 2.0 ~F
= 1.0 ~F
= Enable
= 70.0 ~F
= 60 %
= 15 %
= 130.0 ~F
= Enabled
= 50 %
= 45 Sec
= 100 %
= 100 %
= 100 %
= 100 %
= 100 %
= 100 %
= 0 Min
= 100 %
= 100 %
= 100 %
101