Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EMS FireCellWDC
Summary of Contents for EMS FireCellWDC
- Page 1 Installation Guide ©2019 EMS Ltd. All rights reserved. MK241 Iss 2 20/11/2019 AJM...
-
Page 2: Table Of Contents
Fix oor plate to oor Open re door & depress plunger Post installation con guration Test device Troubleshooting Device tone & ash indication Speci cation Regulatory information ©2019 EMS Ltd. All rights reserved. Page 2 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 3: Ordering Information
Any door closing devices used in conjunction with the WDC must conform to EN 1154. Components FireCell Small & large Fixing template Fixings ESD protection oor plates (MK255) label ©2019 EMS Ltd. All rights reserved. Page 3 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 4: Equipment Familiarisation
15 seconds and concludes with three low pitched beeps. Should the sequence close with a mix of high and low pitched beeps, refer to page 13. ©2019 EMS Ltd. All rights reserved. Page 4 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 5: Add To System - Unprogrammed Systems Only
Free to download from www.emsgroup.co.uk Note: the device can also be programmed utilising the control panel’s cause and e ects, as part of the buildings evacuation plan. ©2019 EMS Ltd. All rights reserved. Page 5 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 6: Assign Device
ESD protection label must be tted. Simply a x the label inside the xing template’s cut out, on to the metal surface. ©2019 EMS Ltd. All rights reserved. Page 6 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 7: Drill Xing Positions
Drill xing positions Drill all four xing positions. = 2.5mm Fix unit to door Use all four xing positions. Use supplied xing screws. ©2019 EMS Ltd. All rights reserved. Page 7 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 8: Position Oor Plate
Ferrule Floor plate Side view Mark oor plate xing positions Mark all four xing positions. Use small oor plate, if bumpstop creates a trip hazard ©2019 EMS Ltd. All rights reserved. Page 8 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 9: Drill Oor Plate Xing Positions
& electrical cables = 6 mm Fix oor plate to oor Use all four xing holes. Use supplied xing screws. ©2019 EMS Ltd. All rights reserved. Page 9 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 10: Open Re Door & Depress Plunger
Input Output Device To Exit BACK The device must now be assigned to the system. Refer to the ‘ Assign Devices’ section on page 6 for details. ©2019 EMS Ltd. All rights reserved. Page 10 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 11: Test Device
Test device ©2019 EMS Ltd. All rights reserved. Page 11 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 12: Troubleshooting
Do NOT Press the log on button on a pre-programmed device, as this will cause communication with the control panel to be lost. Should this happen, delete the device from the system and add it back on. ©2019 EMS Ltd. All rights reserved. Page 12 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 13: Device Tone & Ash Indication
† Door closing can be as a result of many factors such as a fire condition, a loss of communication or a battery critical condition. Refer to the control panel for details. ©2019 EMS Ltd. All rights reserved. Page 13 of 16... -
Page 14: Speci Cation
Max. test door friction 0.8 Nm Min. angle between door open 66 ° and closed positions Note: FireCell WDC is not for use on metal doors. ©2019 EMS Ltd. All rights reserved. Page 14 of 16 MK241 Iss 2 20/11/2019 AJM... -
Page 15: Regulatory Information
March 2012. Fire detection and re alarm systems. Part 25: Components using radio links. European Union directives EMS declares that the radio equipment type FireCell WDC is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.emsgroup.co.uk... - Page 16 The information contained within this literature is correct at time of publishing. EMS reserves the right to change any information regarding products as part of its continual development enhancing new technology and reliability. EMS advises that any product literature issue numbers are checked with its head o ce prior to any formal speci cation being written.