Table of Contents
Advertisement
. . . . . Procedure of setting SELECT SOURCE NAME
Sets the source terminals that can be selected for a specific
destination terminal. The terminals are not enabled and
disabled individually. Instead, a range of terminals is set as
enabled.
1. Press [Ctrl] _ [F] to switch to the SELECT SOURCE
NAME screen.
2. Select an item to set using the cursor key.
3. Pressing [Enter] establishes the source name input
mode.
4. Enter the "Type + No." name or description name.
1) When [J : NAME STYLE (Type + Num)] is
selected in the primary station menu, input the
type name (between 0 and F) and the number for
the source and destination name.
2) Each time [Ctrl] _ [N] is pressed when [J :
NAME STYLE (DESCRIP. NAME)] is selected
in the primary station menu, the following input
mode will be switched alternately.
When "Ctrl_ N : Type + Num" is displayed on the
screen, it means that the name mode will be changed to
"Type + Number" by pressing [Ctrl] _ [N].
Description name input mode :
Input Description name from the first to seventh
characters using the alphabet and numerical keys.
"Type + Number" name input mode:
Input in the same way as 1).
5. Press [Enter] to confirm the input contents.
Example of setting
Block
Source
(Used area)
(Input range)
TOP
1
1
2
101
3
101
When the ranges of input and output selections are limited
as shown in the above table, the setting display and the
virtual matrix are configured as shown below.
3-14
Destination
(Output range)
END
TOP
END
64
1
64
164
1
64
164
101
164
SONY ROUTING SYSTEM SETUP MENU
SELECT SOURCE NAME
SRC TOP -SRC END =DST TOP -DST END
001 IN001
-IN064
=OUT001 -OUT064
002 IN101
-IN164
=OUT001 -OUT064
003 IN101
-IN164
=OUT101 -OUT164
004 ....... -....... =....... -.......
005 ....... -....... =....... -.......
006 ....... -....... =....... -.......
007 ....... -....... =....... -.......
008 ....... -....... =....... -.......
0=IN
1=OUT
2=SONY
3=VTR
8=PGM
9=CL
A=SL
B=L
G=L/A
H=REM
I=CAM
J=STDO
O=SAT
P=CG
Q=WETH
R=TEST
Ctrl-E:MENU Ctrl-D:RETURN Ctrl-N:Type + Num Ctrl-F:SELECT DESTINATION
Example of Selectable Source Range Setting Screen
(Input)
1024
164
101
Block 2
Block 3
Virtual matrix
m
1. When selecting the destinations that have no limit of
range, the selectable range of sources is from 1 to 1024.
When the selections are the same as the example of the setting
screen, all of the sources 1 to 1024 can be selected for OUT065.
2. Sources included in the range of the selected destina-
tion will be all set enables. When selected by the
example setup screen, OUT001 will enable multiple
ranges of IN001 - IN064 and IN101 - IN164.
To return to the menu screen of the secondary station
Press [Ctrl] _ [E].
To return to the menu screen of the primary station
Press [Ctrl] _ [D].
BKS-R3219A V2.23 STATION NUMBER 4
4=SUP
5=CB
6=AIR
7=ME
C=RET
D=MIX
E=JEEP
F=OSC
K=AUX
L=COV
M=BS
N=CS
S=HD
T=D1-
U=D2-
V=SEG
64
1
Block 1
64
101
164
1024
(Output)
: Set range
: Unset range
BKS-R3219A/R1617A I&SSM
Advertisement
Table of Contents
