Subscribe to Our Youtube Channel
Related Manuals for Acromag IP440 Series
Summary of Contents for Acromag IP440 Series
- Page 1 (217) 352-9330 | Click HERE Find the Acromag IP440-1 at our website:...
- Page 2 Wixom, MI 48393-7037 U.S.A. Tel: (248) 624-1541 Fax: (248) 624-9234 Copyright 1996, Acromag, Inc., Printed in the USA. Data and specifications are subject to change without notice. 8500-551-F04K004 Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com...
-
Page 3: Table Of Contents
IMPORTANT SAFETY CONSIDERATIONS The information contained in this manual is subject to change without notice. Acromag, Inc. makes no warranty of any kind with It is very important for the user to consider the possible adverse regard to this material, including, but not limited to, the implied effects of power, wiring, component, sensor, or software failures in designing any type of control or monitoring system. -
Page 4: Industrial I/O Pack Interface Features
“INFO440.TXT” file in the appropriate “IP470” subdirectory off of boards are also supported (see Acromag Model APC8600). A “\VMEIP” or “\PCIP”, according to your carrier. wide range of other Acromag IP modules are also available to serve your signal conditioning and interface needs. 2.0 PREPARATION FOR USE... -
Page 5: Board Configuration
This model is directly loopback compatible with CONNECTORS the Acromag Model IP445 Digital Output Module. Likewise, pin assignments are identical to those of Acromag Model IP400 40- IP Field I/O Connector (P2) Channel Digital Input Boards for channels 0-31. This model may... -
Page 6: Noise And Grounding Considerations
SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Note that the inputs of this device are bipolar, and may be Threaded metric M2 screws and spacers are supplied with the IP connected in any direction with respect to the port common. module to provide additional stability for harsh environments (see Further, do not confuse port commons with signal ground. -
Page 7: Standard (Default) Mode Memory Map
SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Notes (Table 3.1A): This manual is presented using the “Big Endian” byte 1. Writes to these registers are possible, but this model is ordering format. Big Endian is the convention used in the intended for input only and writes should not be done. -
Page 8: Register Definitions
SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Table 3.1B: IP440 R/W Space Address (Hex) Memory Map Table 3.1B: IP440 R/W Space Address (Hex) Memory Map EVEN EVEN Base Base Base Base Addr+ Addr+ Addr+ Addr+ ENHANCED MODE, REGISTER BANK [1] DEFINITIONS: INDEPENDENT FIXED FUNCTION REGISTERS: READ - Port 0 Not Driven... - Page 9 SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Write Mask Register & Enhanced Mode Select Register Enhanced Mode Write Mask Register (Port 7) (Standard Mode, Port 7, Read/Write) WRITE TO REGISTER READ FROM REGISTER Port 0 Write Mask Port 0 Write Mask The ASIC used by the IP440 is capable of output.
- Page 10 SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Event Interrupt Status Register For Ports 0-3 Bank Select Register (Enhanced Mode Bank 1, Port 6, Read Only) Function NOT USED Reading this register will return the event interrupt status of Bank Select Bit 0 input ports 0-3 (bits 0-3) and the interrupt status flag (bit 7).
- Page 11 All IP's have 'IPAC' INDEPENDENT FIXED FUNCTION CONTROL REGISTERS Interrupt Enable & Software Reset Register (Read/Write) Acromag ID Code IP Model Code Bit 0 of this register specifies if the internal event sense Not Used (Rev) interrupts are to be reported to the carrier or not (i.e. whether they Reserved drive INTREQ0 or not).
-
Page 12: The Effect Of Reset
IP440 PROGRAMMING interrupts disabled. The data pattern to be written is 07H, 0DH, 06H, and 12H, and this must be written immediately after reset or Acromag provides an Industrial I/O Pack Software Library power-up. diskette (Model IPSW-LIB-M03, MSDOS format) to simplify communication with the board. -
Page 13: Change-Of-State Detection
SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Change-Of-State Detection Note that the state of the inputs (on/off) is determined by reading the corresponding port address while in bank 0 of the Change-of-State signal detection requires that both a high-to- Enhanced Mode. -
Page 14: Theory Of Operation
SERIES IP440 INDUSTRIAL I/O PACK 32-CHANNEL ISOLATED DIGITAL INPUT MODULE ___________________________________________________________________________________________ Note that Debounce Duration Register 1 (port address 2) 11. Read 01H from the port 7 address to verify bank 0 access would be used to configure debounce durations for ports 4 & (bits 6 &... -
Page 15: Logic/Power Interface
It is highly recommended that a non-functioning to 250VAC, or 354V DC on a board be returned to Acromag for repair. The board can be easily continuous basis (unit will damaged unless special SMT repair and service tools are used. -
Page 16: Inputs
Debounce times are Cable: 50-wire flat ribbon cable, 28 gage. Non-Shielded cable programmable and derived from model uses Acromag Part 2002-211 (3M Type C3365/50 or the 8MHz system clock, in equivalent). Shielded cable model uses Acromag Part 2002- combination with the debounce 261 (3M Type 3476/50 or equivalent). -
Page 17: Termination Panel: Model 5025-552
Connects to Schematic and Physical Attributes: See Drawing 4501-464. Acromag termination panel 5025-552 from the rear of the Field Wiring: 50-position terminal blocks with screw clamps. card cage, and to AVME9630/9660 boards within card cage, Wire range 12 to 26 AWG. -
Page 18: 4501-434 Ip Mechanical Assembly
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com... -
Page 19: 4501-603 Ip440/445 Loopback Connections
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com... -
Page 20: 4501-462 Cable 5025-550 (Non-Shielded)
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com... -
Page 21: 4501-464 Termination Panel 5025-552
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com...
Need help?
Do you have a question about the IP440 Series and is the answer not in the manual?
Questions and answers