Subscribe to Our Youtube Channel
Related Manuals for elsner elektronik KNX DALI L4 bc 16 A
Summary of Contents for elsner elektronik KNX DALI L4 bc 16 A
- Page 1 KNX DALI L4 bc 16 A Actuator for DALI Light Control Item number 70580 Installation and Adjustment...
-
Page 3: Table Of Contents
6.3.3. Colour control ..................... 23 6.3.4. Scenes ......................24 Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany Actuator KNX DALI L4 bc 16 A • from application 1.0 Status: 18.05.2020 • Subject to technical changes. Errors excepted. - Page 4 Clarification of signs Installation, inspection, commissioning and troubleshooting of the device must only be carried out by a competent electrician. This manual is amended periodically and will be brought into line with new software releases. The change status (software version and date) can be found in the contents footer. If you have a device with a later software version, please check www.elsner-elektronik.de in the menu area "Service"...
-
Page 5: Description
DALI EVGs with device type 8. Both colour settings can be controlled by scenes, relative or absolute dimming. In addition to normal operation, the KNX DALI L4 bc 16 A has a night mode and a staircase lighting function with prewarning function (and both in combination). -
Page 6: Technical Data
VDE regulations and national regulations are to be followed. • Ensure that all lines to be assembled are free of voltage and take precautions against accidental switching on. Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... - Page 7 Elsner Elektronik is not liable for any changes in norms and standards which may occur after publication of these operating instructions. Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
-
Page 8: Device Connection And Design
LED "lamp" Channel A: LED on: Switched on (DALI) LED off: Switched off (DALI) Connections switching output Channel A 10 Connections DALI Bus A Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 9: Insulation Properties Of The Clamp Groups
Installation and commissioning The Actuator KNX DALI L4 bc 16 A is installed on a DIN rail (in-line installation on top-hat rail). The connection to the KNX data bus is made via a KNX connection termi- nal and is insulated according to the requirements of SELV circuits. In addition, the de- vice is connected to the mains voltage, which is also used to switch the DALI devices. -
Page 10: Connection Example
After the operating voltage has been applied, the device will enter an initialisation phase lasting a few seconds. During this phase no information can be received or sent via the bus. Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 11: Buttons And Leds For The Output Channels
After use, the device must be disposed of or recycled in accordance with the legal reg- ulations. Do not dispose of it with the household waste! Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 12: Transmission Protocol
% status DPT_Scaling DALI A staircase mode Input -WC- [1.3] 1 Bit DPT_Enable DALI A staircase light status Output --CT [1.3] 1 Bit DPT_Enable Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... - Page 13 1 Byte DPT_Scaling DALI A white status % Output --CT [5.1] 1 Byte DPT_Scaling DALI A RGB setpoint % Input -WC- [232.600] 3 Bytes DPT_Colour_RG Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 14 [5.1] 1 Byte DPT_Scaling DALI B dimming Input -WC- [1.3] 1 Bit DPT_Enable DALI B night mode status Output --CT [1.3] 1 Bit DPT_Enable Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 15 DALI B RGB colour saturation Input -WC- [3.7] 4 Bit setpoint dimming DPT_Control_Di mming DALI B red status % Output --CT [5.1] 1 Byte DPT_Scaling Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 16 DALI C switch-on value % Input/ RWCT [5.1] 1 Byte Output DPT_Scaling DALI C night mode brightness Input -WC- [3.7] 4 Bit setpoint % DPT_Control_Di mming Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 17 DALI C blue setpoint % Input -WC- [3.7] 4 Bit DPT_Control_Di mming DALI C red setpoint dimming Input -WC- [3.7] 4 Bit DPT_Control_Di mming Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 18 [5.1] 1 Byte DPT_Scaling DALI C scenario Input -WC- [18.1] 1 Byte DPT_SceneCont DALI C front control block Input -WC- [1.3] 1 Bit DPT_Enable Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 19 1 Byte DPT_Scaling DALI D white setpoint % Input -WC- [5.1] 1 Byte DPT_Scaling DALI D white setpoint dimming Input -WC- [5.1] 1 Byte DPT_Scaling Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 20 DALI D RGBW setpoint % Input -WC- [3.7] 4 Bit DPT_Control_Di mming DALI D RGBW status % Output --CT [5.3] DPT_Angle 1 Byte Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
-
Page 21: Setting The Parameters
No • Yes Use DALI Bus B No • Yes Use DALI Bus C No • Yes Use DALI Bus D No • Yes Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 22: Dali Bus A / B / C / D
0...100; 80% KNX bus value 0...100; 20% corresponds to the lamp 0...100; 50% KNX bus value corresponds to the lamp 0...100; 30% Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 23: Brightness Control
Behaviour of % status object Readable • Send if changed Transmit status cyclically Never • every 5 seconds • ... • every 4 hours (if status is sent) Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... - Page 24 Never • every 5 seconds • ... • every 4 hours (if status is sent) Night mode with staircase light See “Night mode” on page 22. See “Staircase light” on page 22. Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
-
Page 25: Colour Control
• RGB with separate objects • RGB with HSV Behaviour colour change with % object in 1 second • ... • in 4 minutes Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... -
Page 26: Scenes
Last saved value should be • Power failure not • Power failure • Power failure and ETS download should be maintained Scenes are in 1 ... 240 seconds Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted... - Page 27 Red - proportion 0 ... 255 Green - proportion 0 ... 255 Blue - proportion 0 ... 255 White - proportion 0 ... 255 Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted...
- Page 28 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de Technical support: +49 (0) 70 33 / 30 945-250...
Need help?
Do you have a question about the KNX DALI L4 bc 16 A and is the answer not in the manual?
Questions and answers