Advertisement
Quick Links
Advertisement
Related Manuals for ParaBody Serious Steel Pro System
Summary of Contents for ParaBody Serious Steel Pro System
- Page 1 893103 PRO SYSTEM ASSEMBLY INSTRUCTIONS Part # 6753901 Revision:10/27/97...
- Page 2 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
- Page 3 PARTS LIST PART # DESCRIPTION PART # DESCRIPTION 6566603 UPRIGHT FRAME 3102933 3/8 X 2” BOLT 6566702 TOP BOOM 3102502 1/2” WASHER 6546302 CARRIAGE 3102501 3/8” WASHER 6566903 BENT TUBE 3102602 1/2” LOCK WASHER 6567002 UPRIGHT 3102601 3/8” LOCK WASHER 6581102 LAT BAR 3102801...
- Page 4 1/2 X 3-1/4” 26 FIGURE 2 STEP 2: • Assemble two COVER CAPS (48) to the ends of the BENT TUBE (4) as shown in FIGURE 2. • Insert two 2” SQ. END CAPS (47) to the ends of the UPRIGHT FRAME (1) as shown in FIGURE 2. •...
- Page 5 3/8 X 2-3/4” 28 FIGURE 3 STEP 3: • LOOSELY assemble the UPRIGHTS (5) to the BENT TUBE (4) using four 3/8 X 2-3/4” BOLTS (28) and four 3/8” LOCK- NUTS (36) as shown in FIGURE 3. • Attach UPRIGHT LABELS (22) to both of the UPRIGHTS (5) as shown in FIGURE 3.
- Page 6 TRIM EXCESS FIGURE 4 STEP 4: • Attach ten 1-1/2 X 3/4” GLIDES (54) to both SAFETY RAILS (9) as shown in FIGURE 4. • SECURELY assemble one SPRING PIN ASSEMBLY (40) to both SAFETY RAILS (9) as shown in FIGURE 4. •...
- Page 7 FIGURE 6 STEP 6: • Pull back the SPRING PIN and slide the SAFETY RAILS (9) over the UPRIGHTS (5) until the SPRING PIN is engaged in the first hole. • Slide the CARRIAGE (3) over the UPRIGHT FRAME (1) as shown in FIGURE 6. 3/8 X 2-3/4”...
- Page 8 Route CABLE over bolts. 27 1/2 X 3” 28 3/8 X 2-3/4” 1/2 X 3” 27 FIGURE 8 STEP 8: • LOOSELY assemble the TOP BOOM (2) to the UPRIGHT FRAME (1) using two 1/2 X 3” BOLTS (27), one 3/8 X 2-3/4” BOLT (28), one 1/2”...
- Page 9 STEP 10: • Assemble two 4 X 7” ROLLER PADS (20) to the SWIVEL KNEE SUPPORT (10) using two STARLOCK COLLARS (49) as shown in FIGURE 10. FIGURE 10 1/2 X 3-1/4” 26 35 1/2” LOW HT. LOCK FIGURE 11 STEP 11: •...
- Page 10 29 3/8 X 2” FIGURE 12 STEP 12: • LOOSELY assemble two 3-1/2” PULLEYS (23) and two CABLE RETAINING CLIPS (56) to the CENTER PULLEY BRACKET (16) using two 3/8 X 2” BOLTS (29), two 3/8” WASHERS (31), and two 3/8” LOCKNUTS (36). See FIGURE 12. STEP 13: •...
- Page 11 26 1/2 X 3-1/4” FIGURE 14 STEP 14: • SECURELY assemble the BEARING HOUSING (13) and the CENTER PULLEY BRACKET (16) to the UPRIGHT FRAME (1) using two 1/2 X 3-1/4” BOLTS (26) and two 1/2” LOCKNUTS (34) as shown in FIGURE 14. STEP 15: •...
- Page 12 FIGURE 16 STEP 16: • Assemble the LEFT (15) & RIGHT (14) PEC ARMS to the BEARING HOUSING (13) using four 3/4” FLANGE BEARING (41) and two 3/4” CAP NUTS (52) as shown in FIGURE 16. 3/8 X 2-3/4” 28 STEP 17: •...
- Page 13 LAT CABLE & LOW ROW CABLE PEC DEC CABLE 24 893103 CABLE DIAGRAM • Refer to the 839103 CABLE DIAGRAM for help with STEPS 17-27...
- Page 14 STEP 18: FIGURE 18 3/8 X 2-3/4” 28 • Create a loop in the CABLE (25) then wrap the CABLE (25) around the groove of a 3-1/ 2” PULLEY (23) and SECURELY assemble the PULLEY (23) to the TOP BOOM (2) using one 3/8 X 2-3/4”...
- Page 15 FIGURE 20 3/8 X 2” 29 3/8 X 2-3/4” 28 STEP 20: • SECURELY assemble one 3-1/2” PULLEY (23) and one CABLE RETAINING CLIP (56) to the plate on the UPRIGHT FRAME (1) using one 3/8 X 2” BOLT (29), one 3/8” WASHER (31), and one 3/8” LOCK NUT (36). See FIGURE 20. •...
- Page 16 STEP 22 • Wrap the PEC DEC CABLE (24) around one 3-1/2” PULLEY (23) and assemble the PULLEY to the PULLEY BRACKET (11) using one 3/8 X 2” BOLT (29) and one 3/8” LOCKNUT (36) as shown in FIGURE 22. 3/8 X 2”...
- Page 17 3/8 X 2-3/4” 28 FIGURE 24 STEP 24: • Route the CABLE (25) under the 3-1/2” PULLEY in the slot on the FRONT UPRIGHT (1) and around the 3-1/2” PULLEY shown on FIGURE 24. (NOTE: Make sure CABLE (25) is underneath the CABLE RETAINING CLIP.) •...
- Page 18 3/8 X 2” 29 FIGURE 25 STEP 25: • Loop the CABLE (25) around one 3-1/2” PULLEY (23) and LOOSELY assemble PULLEY to the 1-3/4 X 5-1/4” PLATES (17) using one 3/8 X 2” BOLT (29) and one 3/8” LOCK NUT (36). See FIGURE 25.
- Page 19 FIGURE 26 STEP 26: • Route CABLE (25) around PULLEY and under the CABLE RETAINING CLIP on FRONT UPRIGHT (1) as shown in FIGURE • Attach the CABLE (25) to the PULLEY BRACKET (11) using one QUICK LINK (38) as shown in FIGURE 26. •...
- Page 20 FIGURE 27 STEP 27: • Attach two 1 X 8” GRIPS (50) to the LAT BAR (6) and two 1 X 8” GRIPS (50) to the LOW ROW BAR (18) as shown in FIGURE 27. (TIP: Spray window cleaner on the inside of the grip to help ease assembly.) •...