Kwikset OBSIDIAN Installation And User Manual page 3

7
Add the lock to your smart home system
Initiate the process to add the
A
lock to your system at your smart
home controller. Refer to your
smart home system instructions
for more information.
8
Add user codes (30 max)
It is recommended that you add and delete all user codes through your smart home system.
If your system does not allow this, codes may be added directly to the lock as shown here.
Programming information
A
Mastercode: For enhanced security, a
mastercode may be used when adding and
deleting user codes. For more information
about the mastercode, download the
Programming and Troubleshooting Guide at
www.kwikset.com.
Programming Timeout: During
programming, if the screen is not pressed
for 20 seconds, the system will time out
(indicated by three beeps and the "X" pattern
flashing three times), and you will need to
restart the procedure.
F
What digits and sounds did the lock produce?
Checkmark symbol with one beep
9
Test the lock (review normal operation)
Confirm that the code(s) added in previous step can unlock the door.
Activating the Screen
Option 1 Option 2
Touch screen with Touch lower left
palm or back of area of screen
hand until digits (where checkmark
illuminate. is located) until
digits illuminate.
10
Install the interior cover
Important Information about the interior cover
The window on the
interior cover is
locked by default to
prevent someone
from tampering with
your lock's settings.
window
Cover Installation
a
Install cover.
Note: You may need to
rotate the turnpiece to align
with the turnpiece shaft.
When prompted by your smart home system to add the
B
lock, press button "A" on the lock interior four times.
button "A"
Make sure the door
B
is open. Press the
Program button once.
1x
Programming was successful.
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See "Switches and Status LED Colors" on page 4.
Locking the Door
Option 3 1. Activate the screen.
2. Press Lock symbol.
Touch screen
Note: If no user codes are
with three or
programmed, the door cannot
more fingers until
be locked via touchscreen.
digits illuminate.
If you wish to unlock
the window, you can
slide it up for more
convenient access
to the programming
buttons while the
cover is installed.
G
turnpiece
turnpiece
shaft
C
If successful, re-name the lock in your system (if applicable).
If unsuccessful, press button "B" nine times.
D
button "B"
Perform steps 7A-7C again.
If still unsuccessful, consult the Programming and
Troubleshooting Guide on the Obsidian page at www.kwikset.com.
Press checkmark
C D
symbol once.
"X" pattern with three beeps
or
Move swiftly through
programming, as the system
will time out if no button is
pressed for 20 seconds.
Unlocking the Door
1. Activate the screen.
2. If SecureScreen is enabled, touch
the random digits that appear.
3. Enter user code.
If you press the wrong digit while entering
a user code, you can press the Lock symbol
once to clear the digits entered previously and
immediately restart the code entry process.
To unlock the
window, remove
the security screw.
b
Install screws.
3 / 4
Enter user code. A total
E
Press lock symbol once.
of 30 user codes may
be programmed.
Each user code must be
a unique code between 4
and 8 digits, depending on
your smart home system.
3x
Make sure the user code is Make sure the lock has
not a duplicate and that it room for an additional code.
is between 4 and 8 digits If all user code positions
during your next attempt. are filled, delete a code to
make room for this one.
SecureScreen™
SecureScreen is an added-security feature
that displays random digits before you enter
a user code to unlock the door. This feature
ensures that there are fingerprints on all
digits so that codes cannot be identified by
examining the touchscreen for finger prints.
Note: The interior
U (x3)
cover and screws
must be removed for
battery pack access.
If desired, this feature
can be disabled by
turning switch #4 to
the off position. See
"Switches and Status
LED Colors" on page 4.
actual
size
U