Advertisement
Quick Links
Advertisement
Related Manuals for Kwikset HALO TOUCH 959TRL
Summary of Contents for Kwikset HALO TOUCH 959TRL
- Page 1 English 66856 Rev 01 Installation and Reference Guide...
- Page 2 Welcome to the Kwikset family! This guide will get you up and running with your new Halo Touch Fingerprint Smart Lock. If you have any issues, please visit our support center: kwikset.com/halo-touch or call us at 1-800-327-5625.
- Page 3 Getting started For an interactive version of this installation guide, please download the Kwikset app: kwikset.com/app...
-
Page 5: Table Of Contents
Table of contents Parts in the box ..........4 Required tools ..........5 Installation ............7 Download the app.........17 Reference guide ..........19... -
Page 6: Parts In The Box
Parts in the box Exterior assembly Battery pack Interior assembly Interior cover Step actual 03809 size Latch Step actual 46780 size Strike... -
Page 7: Required Tools
Required Step Step tools actual 49191 size Mounting plate Step Keys Batteries SmartKey™ tool actual 64844 size actual 68611 size actual 64109 size Phillips head screwdriver No electric drills... -
Page 8: Installation
Installation... - Page 9 Remove your existing deadbolt 1-3/4” to 2” (44mm - 51mm) 2-1/8” (54mm) If drilling a new door, use the supplied template and instructions available at: kwikset.com/doorprep...
- Page 10 Install the latch Extend the latch bolt. If your door requires a drive-in latch, please contact Kwikset at 1-800-327-5625. UP is on top. 03809* (2X) If the D-shaped hole is not centered in the door hole, rotate the latch face to extend the latch.
- Page 11 Install the strike 46780* (4X) *Install the longer screws closest to the door jamb. DOOR JAMB 1" (25 mm) hole depth...
- Page 12 Install the exterior assembly [OUTSIDE] Cable goes under the latch.
- Page 13 [INSIDE] Keep parallel to the door edge Tighten the screws evenly. DO NOT over-tighten. 64844 (2X) Route the cable Insert the key and through the center test the latch. If the hole, then push into latch does not extend the bottom hole. or retract smoothly, adjust the screws.
- Page 14 Install the interior assembly Make sure the turnpiece shaft is pointing up as shown below. Remove the interior cover from the interior assembly. Incorrect: If the turnpiece shaft is not pointing up, put the cover back on and rotate the turnpiece until you hear a click.
- Page 15 Connect the cable. Ensure a tight cable connection. align Secure the interior assembly onto the mounting plate. Lay cable flat inside the bottom of the interior housing. 49191 (2X) Ensure the spindle fully engages with the turnpiece shaft. [INSIDE]...
- Page 16 Perform the door handing process With the door open, install Install 4 AA batteries into the battery pack. the battery pack to initiate auto-handing. NOTE: Lock must be installed on the door before installing the battery. The latch will retract and extend to learn the orientation of the door.
- Page 17 You may need to rotate the turnpiece to align with the Secure the interior turnpiece shaft. cover onto the interior assembly. For additional security, you may 64109 choose to lock the window by installing the security screw. (3X) 68611 (1X) When the window is locked, you will need to remove the entire cover to access the battery pack...
-
Page 18: Download The App
Download the app & create an account... - Page 19 Follow the setup instructions in the Kwikset app to create your account: kwikset.com/app The Kwikset app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.
-
Page 20: Reference Guide
Reference Guide... - Page 21 Locking Unlocking To lock your door, place any finger To unlock your door, place your on the fingerprint sensor. The enrolled finger on the fingerprint light bar will display the following sensor. The light bar will display the animations, beep once, and the following animations, beep once, door will lock.
- Page 22 Enabling Amazon Enabling Google Alexa Assistant Follow the setup Follow the setup instructions to enable instructions to enable Amazon Alexa: Google Assistant: Amazon Alexa Guide Google Assistant Guide...
- Page 23 SmartKey Re-key Re-key the lock to work with your existing key by following the SmartKey Re-key instructions. NOTE: If Auto-Lock is enabled, remove the battery pack before re-keying your lock.
- Page 24 Exterior LED Indicators Orange: Green: Locking Unlocking Blue: Red: Authenticating fingerprint Low battery or door jam...
- Page 25 Interior LED Indicators Green Solid: Blinking: Solid: Blinking: Action successful Unlocked Door handing Low battery or unsuccessful action unsuccessful Blue Orange Solid: Blinking: Solid: Blinking: Bluetooth pairing Bluetooth pairing Entering network Locked or network/ successful mode reset mode system mode...
- Page 26 Device Router Compatibility Compatibility Please see the Please see the Device Compatibility Router Compatibility list to see if your device list to see if your router is compatible. is compatible. Router Compatibility Device Compatibility NOTE: Halo Touch implements a standard based Wi-Fi radio and should work with majority of the routers available in the market that are Wi-Fi certified.
- Page 27 Manual Door Handing If needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a different door. 1. Remove battery 2. Press and HOLD pack. the Program button while reinserting the battery pack.
- Page 28 Delete the lock from the 2. Remove the lock from the Kwikset app. Bluetooth list on your device by tapping “Forget Device” in the Bluetooth settings. Continue to the next page...
- Page 29 3. Remove battery pack. 4. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 Status seconds or until the lock beeps and the status LED flashes red. Then release the Program button. 5.
- Page 30 Interior (cover removed) Light bar Battery pack Button “A” Button “B” Fingerprint Program sensor button Status LED SmartKey™ tool access Turnpiece shaft Keyway Troubleshooting If you have any issues, please visit our kwikset.com/halo-touch support center: or call us at 1-800-327-5625.
- Page 31 Important Safeguards 1. Read all instructions in their entirety. 5. If using the Auto-Lock features, make sure you have your smartphone or standard key with you 2. Familiarize yourself with all warning and to prevent locking yourself out. caution statements. 6.