Download Print this page
Toro DD2024 Software Manual

Toro DD2024 Software Manual

Directional drill

Advertisement

Quick Links

2024 Directional Drill
Model No. 23800—Serial No. 313000501 and Up
Model No. 23800A—Serial No. 315000001 and Up
Model No. 23800C—Serial No. 315000001 and Up
Model No. 23800TE—Serial No. 315000001 and Up
Model No. 23800W—Serial No. 315000001 and Up
Note: Install kit Model 132-4193 to use software versions
K–V.
Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.
Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers
of your product ready.
You may contact Toro directly at www.Toro.com for product
safety and operation training materials, accessory information,
help finding a dealer, or to register your product.
Monitor
Startup Screen
When you power up the machine, this is the first screen that
appears
(Figure
1).
Note: No keys are active from this screen.
Startup Screen
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
Register at www.Toro.com.
Main Operating Screen
This screen appears after the Startup Screen if there is not an
operator in the seat when the key is turned
To access this screen, press button 4 or the down arrow on
the
Machine-Information Screen (page
The main operating screen displays the engine-rpm gauge,
the fuel-quantity gauge, and the engine-temperature gauge
(Figure
2).
The low-fuel indicator lights up on the main operating screen
when the machine is running low on fuel
Press button number 4 to select the horsepower control
(Figure
2).
Note: The icon for button 8 is only for software versions
K and up
(Figure
g029842
1. Pipe setting
2. Fuel gauge
3. Engine-speed (rpm) gauge 6. Low-fuel indicator
Original Instructions (EN)
Form No. 3411-784 Rev A
Software Guide
ON
5).
(Figure
25).
Figure 2
Main Operating Screen
4. Coolant-temperature
gauge
5. Horsepower control
All Rights Reserved *3411-784* A
Printed in the USA
.
2).
g035949

Advertisement

loading

Summary of Contents for Toro DD2024

  • Page 1 Machine-Information Screen (page product properly and safely. The main operating screen displays the engine-rpm gauge, Whenever you need service, genuine Toro parts, or additional the fuel-quantity gauge, and the engine-temperature gauge information, contact an Authorized Service Dealer or Toro (Figure...
  • Page 2 Main Drill Functions Displayed in the Main Drill Functions Displayed in the Pressure Screen Torque Screen To access this screen, press the down arrow on the Main To access this screen, press the down arrow on the Main Drill Operating Screen (page Functions Displayed in the Pressure Screen (page This screen provides measurements on rotary pressure in psi, This screen provides measurements on rotary torque in...
  • Page 3 Drill-Rotation-Speed Screen Horsepower-Control Screen To access this screen, hold the OK button on the Main The horsepower control allows the user to change the Operating Screen (page engine-speed (rpm) setting that the engine can droop to before the horsepower-control system can activate. This screen allows the user to increase or decrease the maximum rotation speed of the drill.
  • Page 4 Carriage-Pressure Screen Control-Select Screen To access this screen, press the down arrow on the Main Drill Access this screen by selecting Switch Joystick Functions Functions Displayed in the Torque Screen (page from the Carriage-Pressure Screen (page When this screen appears, the carriage-pressure selection The 2 control layouts that the operator can choose from (button 7) is in the O position (green) or O...
  • Page 5 Machine-Information Screen Lubrication and Maintenance Screens This screen contains the following information: These screens provide the user with the daily maintenance schedule and at the 50-hour, 250-hour, 500-hour, and • The machine model and serial number (Figure 1,000-hour increments. • The number of engine hours for the machine (Figure Note: Press the ESC button to exit this screen.
  • Page 6 g029850 g029852 Figure 12 Figure 14 250-Hour Maintenance Screen 1000-Hour Maintenance Screen Error Codes Screen This screen displays the number of drill errors that have occurred. If more than 1 drill error is shown on the screen, press button 6 to see the next drilling error (Figure 15).
  • Page 7 Stored/Reset Error Codes Screen Diagnose and Update Screen Access this screen from the Carriage-Pressure Screen (page Software versions K and up only: use this screen to calibrate the loader cams (Figure 18) as described in Figure Software versions V and up only: use this screen to the auto throttle option (Figure 18).
  • Page 8 Clear-Service-Reminder Screen Air-Cleaner Indicator Screen To access this screen, press button number 1 in the Diagnose This icon will display when the air-cleaner filter needs to be and Update Screen (page 7) to select Modify System serviced (Figure 20). Refer to the machine Operator’s Manual Parameters (Figure 18).
  • Page 9 Rotary and Carriage-Service Screen Auxiliary-Activations Screen From the Main Operating Screen (page 1), press button Press the down arrow on the Rotary and Carriage-Service numbers 1 and 5 simultaneously to access this screen. Screen (page 9) to access this screen. The rotary and carriage service screen (Figure 21) provides...
  • Page 10 Drilling-Fluid-Information Screen Track-Drive-Information Screen Press the down arrow on the Auxiliary-Activations Screen Press the down arrow on the Drilling-Fluid-Information (page 9) to access this screen. Screen (page 10) to access this screen. The drilling-fluid-information screen (Figure 23) provides the The track-drive-information screen (Figure 24) provides the following information:...
  • Page 11 Pipe-Row-Selector Screen Loader-Cam-Calibration Screen Software Versions K and up Only Software Versions K and up Only This screen allows you to select the row of pipe(s) that you To access this screen, press button number 1 on the Diagnose want to use. and Update Screen (page To access this screen, press button number 8 on the Main...
  • Page 12 Collision Condition Indicator Screen Pipe-Setting-Selector Screen Software Versions K and up Only Software Versions T and up Only The carriage stops and the icon displays when there is a This screen allows you to reduce the number of operations collision condition between the drill head and the pipe/arm to load pipe.

This manual is also suitable for:

2380023800a23800c23800te23800w