Samsung Galaxy Active Neo Instruction Manual page 89

Wi-Fi
You can use Wi-Fi function of the terminal to connect to wireless access
point of your home or company network. Also, you can connect to Public
wireless LAN service access point to use mails and Internet.
■ Reception interference caused by Bluetooth devices
The terminal's wireless LAN device and Bluetooth devices use the same frequency
band (2.4 GHz). If you use the terminal near a Bluetooth device, reception
interference may occur or the communication speed may become lower. Also, you
may hear noise or have a connection problem. In these cases, do the following:
1. Keep the wireless LAN device over approximately 20 m away from a
Bluetooth device.
2. Within approximately 20 m, turn off the Bluetooth device.
Information
• Packet communication can also be used even when Wi-Fi function
is ON. However, Wi-Fi will be used first during Wi-Fi connection. If Wi-
Fi network is disconnected, network is automatically switched to
LTE/3G/GPRS. Be noticed that packet communication charge is
applied if you keep using LTE/3G/GPRS network after toggling.
• Connect to a Wi-Fi network that requires user authentication, and
if the user authentication is unestablished when
communications may be carried out not by Wi-Fi, but rather via a
mobile network.
To perform Wi-Fi communications via these kinds of access points, set the
"Smart network switch" to OFF when making connections with access points.
• Setting docomo ID(d ACCOUNT) is required for using docomo service
via Wi-Fi. From the Home screen,
cloud" → "docomo ID 設定 (docomo ID setting)".
• Location information can be detected even if Wi-Fi function is not
ON. From the Home screen,
→ "Always allow scanning" → "Scan always".
■ Enabling Wi-Fi and connecting to network
1
From the Home screen,
2
• Scanning available Wi-Fi networks starts automatically and a list is
displayed.
3
Tap a Wi-Fi network you want to connect → "CONNECT"
• To connect to a Wi-Fi network protected by security, enter a password
(security key) and tap "CONNECT".
• Wi-Fi network available WPS can be connected using WPS (Wi-Fi
Protected Setup). On the Wi-Fi network list screen, "MORE" → "WPS
push button"/"WPS PIN entry" → Operate on access point device.
is displayed,
→ "Settings" → "docomo service/
→ Tap "Settings" → "Wi-Fi", tap "MORE"
→ "Settings" → "Wi-Fi"
Information
• The Wi-Fi network password (security key) is automatically saved when
connection is established so that you do not need to enter it next time.
■ Canceling connection of Wi-Fi network
1
From the Home screen,
2
Tap a connected Wi-Fi network → "DISCONNECT"
■ Setting Wi-Fi access point
• For information necessary for connection, refer to user manual of wireless
LAN access point you use. For connecting to company LAN or using Public
wireless LAN service, ask a network administrator or service provider about
the required information for connecting.
• When the wireless LAN access point is set for connecting only to the
MAC address registered device, register the MAC address of the terminal
to the wireless LAN access point. To check MAC address, from the Home
screen, → "Settings" → "About device" → "Status".
1
From the Home screen,
2
"MORE"
3
"Add network"
4
Enter the network name → Set the security
• The possible certificate method is "WEP", "WPA/WPA2/FT PSK",
"802.1x EAP".
5
Enter a password → "CONNECT"
• If you set Security to "None", entering password is not needed.
■ Setting smart network switch
Set whether to check availability of the connected Wi-Fi network and change
to the mobile network if it is unavailable.
1
From the Home screen,
2
"MORE"
3
"Smart network switch" → "ON"
Information
• When Wi-Fi connection is disconnected with the access point (such as memory
card with embedded wireless LAN which does not connect to Internet) while
"Smart network switch" is ON, set "Smart network switch" to OFF.
87
→ "Settings" → "Wi-Fi"
→ "Settings" → "Wi-Fi"
→ "Settings" → "Wi-Fi"
Settings