Using The Menus 1; Setup Using The Setting Display; The Image Adjustment Menu - Toshiba TLP-X200U Owner's Manual

Using the menus 1

You can call up on-screen menus, and conduct a number of adjustments and settings using
the MENU button on the control panel of the main unit and remote control.
p.16

Setup using the Setting display

■
The menu shown below is for operation instructions purposes and might differ from the
actual display.
1. Press the MENU button
This will display the Setting display menu.
2. Select a Category
Select a category by using .
There are 5 categories:
Image adjustment menu p.37
Display setting menu p.39
Default setting 1 menu p.42
Default setting 2 menu p.43
Status display menu p.45
3. Adjustments & Settings
Press
Item
Adjustment/Setting Value
These marks signify
the items can be
adjusted/set by using
.
These marks signify the items can
be selected from the list by using
.
After an item is selected, apply it by
pressing .
• The figure shows displays given for operation instructions purposes. As the display may differ depending
on the item, refer to the following applicable pages for the menu item you desire.
• To return to previous item, press the RETURN button.
• When Network or USB memory input is selected, pressing the MENU button twice displays the Setting
display (2) menu.
4. End Press the MENU button once more.
(The menu will disappear automatically after 30 seconds, if no operation is conducted.)
Displays the current
adjustments and
settings of the selected
category.
Items shown in gray
cannot be adjusted with
the current input source.
or to open the menu.
These marks signify
that there are setting
These marks
screens. Press
signify that there
to display a list of
are options.
Press or setting screens.
to display a list of
options.
* When no item is
changed, press
Toggle items with .
Select items with and press .
Fix selection with .
36
Note
• Menu adjustments and settings will not be saved, if the power cable is disconnected or
the power goes out before the adjustments and settings have been completed and the
menu display has been closed.

The image adjustment menu

■
Use this menu to set or adjust image related items. Items that can be set or adjusted
are marked "Yes", and those that cannot are marked "No". (When an item is masked, it
indicates that you cannot select it using the current input.)
Item
Adjust the image contrast.
Contrast
Lower
Brightness Adjust the brightness of the image.
Darker
Adjust the color of the image.
Color
Lighter
Sharpness Adjust the sharpness of the image.
Softer
Noise
Set the function to reduce
*1
reduction screen noise.
On (Enable)
Switches the picture mode.
NCE
Press
mode with
for details.
Adjust red of the image color.
R–level
Less red
Adjust green of the image color.
G–level
or
Less green
Adjust blue of the image color.
B–level
Less blue
Set the black level with
NTSC
*2 US
mode
JAPAN : NTSC (JAPAN) mode
.
RGB input Set the RGB input range with
*3
range
Standard : When black color
Full
Automatically adjusts items
Auto
such as the sampling phase
setting
depending on the type of
input signal.
Equalizer Reduce noise on the screen.
Adjust with
Description Computer Y/P /P HDMI Video S-video Network USB memory
B R
Yes Yes Yes
Higher
Yes Yes Yes
Brighter
No Yes No
Deeper
Yes No Yes
Sharper
No Yes No
Off (Disable)
. Toggle the NCE
Yes Yes Yes
. See p.33
Yes Yes Yes
More red
Yes Yes Yes
More green
Yes Yes Yes
More blue
.
: NTSC (US) mode No No No
.
No No Yes
becomes lighter.
: When dark area
becomes too dark.
Yes No No
No No Yes
.
37
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes No No
Yes Yes No Yes
Yes Yes No No
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes No No
No No No No
No No No No
No No No No