Related Manuals for Precor Resolute RSL 714
Summary of Contents for Precor Resolute RSL 714
- Page 1 ENGLISH Resolute™ Strength Selectorized Line Abdominal Crunch RSL 714 Assembly Guide...
-
Page 2: Assembly Requirements
It takes about 90 minutes to assemble this equipment. If this is your first time doing this, allow more time. CAUTION At least two people are required to assemble the equipment. DO NOT attempt to assemble this by yourself. Precor recommends that all strength equipment be bolted to the flooring at all anchoring points. -
Page 3: Parts List
Button head cap screws (BHCS) 5/16-inch x 1½-inch Shroud, rear middle Washers, 9 mm Shroud, front middle (left and right) Shroud, rear upper Shroud, front upper placard Shroud, top tray Weight labels ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide... -
Page 4: Frame Assembly
Hand tighten only. These will be removed tem- washers, 11 mm porarily in a later step. M12 x 125 mm SHCS Connect lower cross brace to main frame washers, 13 mm Tool: Hex wrench, 10 mm ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide... - Page 5 55 ft-lb (75 N-m). Socket wrench, 19 mm Torque wrench Do not tighten the M10 screws installed in step 1 at this time. They will be removed temporarily in a later step. ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide...
-
Page 6: Moving Parts
11 mm Tighten to 32 ft-lb (43 N-m) of torque. M10 x 20 mm SHCS Tools: Mallet Hex wrench, 8 mm Torque wrench ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide... -
Page 7: Route The Cable
To route the cable to the upper pulleys of weight stack tower, remove the cable retainers, route the cables, and replace the retainers. Tighten to 50 Open-end wrench, 19 mm ft-lb (67 N-m) of torque. Torque wrench ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide... -
Page 8: Seat Assembly
Image Hardware Instructions M10 x 125 mm BHCS Remove the guide rod fasteners installed in step 1 of the Frame Assembly. washers, 11 mm Tool: Hex wrench, 6 mm ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide... - Page 9 The plates and top plate should align flush on the top plate assembly user side. Straighten the guide rods to a vertical position. Have your assistant lift the guide rods into the upper part of the frame. ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide...
- Page 10 Replace the cap to the top of the rod and secure top of rod to weight stack tower frame. washers, 11 mm M10 nylon lock nut Tools: Hex wrench, 8 mm Socket wrench, 17 mm ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide...
- Page 11 Peel the extra label away and rub remaining labels again. Lubricate the guide rods with a Teflon-based lubricant, such as Tri-Flow Supe- rior Lubricant. Remove any excess with a clean cloth or tissue. ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide...
- Page 12 M10 x 40 mm SHCS Place shroud crown on top and secure. Recommended bolt torque is 25 ft-lb (34 N-m). Tools: Hex wrench, 8 mm Torque wrench Securely snap top tray into place. ©2019 Precor Inc. | Abdominal Crunch RSL 714 | Assembly Guide...
-
Page 13: Complete The Assembly
Complete the Assembly Precor recommends that the strength equipment be bolted down at all anchoring points. Adjust the round feet on the frame up or down by turning them left or right to help level the equipment. Anchor each oblong foot on the frame to the floor, including the feet on the weight stack tower. Each oblong foot has a rubber cap with slits to allow access the anchor points. - Page 14 RSL Abdominal Crunch 714 | Assembly Guide | P/N CW39585-101 ENG © Precor, Incorporated | 30 August 2019...