MODEL MX-M160D MX-M200D DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information and copier) PART 1: GENERAL INFORMATION • BEFORE USING THE PRODUCT • TROUBLESHOOTING AND MAINTENANCE • PERIPHERAL DEVICES AND SUPPLIES PART 2: COPIER OPERATION • COPY FUNCTIONS • CONVENIENT COPY FUNCTIONS •...
Page 2
All information included herein is subject to change without notice. SHARP is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation. • Sharpdesk is a trademark of Sharp Corporation. • Sharp OSA is a trademark of Sharp Corporation. • RealVNC is a trademark of RealVNC Limited. • All other trademarks and copyrights are the property of their respective owners.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during use of the product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due to use of the product.
CONTENTS Part 1: General Information PRODUCT CONFIGURATIONS ... 3 CAUTIONS... 6 ● CAUTIONS ON USING... 6 ● LASER INFORMATION ... 7 INSTALLATION REQUIREMENTS ... 8 ● ENVIRONMENTAL INFORMATION... 8 MANUALS PROVIDED WITH THE PRODUCT... 9 MAIN FEATURES ... 10 BEFORE USING THE PRODUCT PART NAMES AND FUNCTIONS ...
Page 7
Part 2: Copier Operation COPY FUNCTIONS NORMAL COPYING ... 45 ● MAKING A COPY DARKER OR LIGHTER ...48 ● SELECTING THE TRAY...49 ● SETTING THE NUMBER OF COPIES ...49 ● SELECTING THE ORIGINAL SIZE ...50 ● USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL...51 REDUCING OR ENLARGING A COPY...
CAUTIONS Follow the cautions below when using this machine. CAUTIONS ON USING Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. Caution: •...
LASER INFORMATION Wave length 785 nm + 10 nm/- 15 nm Pulse times (8.141 µs ± 0.1 µs)/7 mm Output power 0.14 mW - 0.22 mW Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.
MANUALS PROVIDED WITH THE PRODUCT Multiple manuals are provided for use of the machine. Please read each manual as appropriate for the functions that you wish to use. Operation manual (for general information and copier) (this manual): The first half of this manual contains general information on the machine, including safety precautions and the procedures for loading paper, removing misfeeds, and performing regular maintenance.
• First-copy time* at 600 x 300 dpi* • Copying speed is 20 (MX-M200D) or 16 (MX-M160D) copies per minute. This provides a big boost to workplace productivity. *1 Measured after the machine has warmed up following power-on, copying using the document glass (A4 (8-1/2" x 11") paper fed from machine tray 1).
Page 13
Fax function (option) Installation of the optional facsimile expansion kit enables the plain-paper, Super G3 laser fax function to be used. Network connection (option) The optional network expansion kit (MX-NB10) can be installed to enable the machine to be used as a network printer and network scanner.
BEFORE USING THE PRODUCT This chapter contains basic information required for use of the machine. Please read this chapter before using the machine. PART NAMES AND FUNCTIONS USB 2.0 port Connect to your computer to this port to use the printer and scanner functions.
Page 15
(19) (20) (13) Document cover (when installed) Open to make a copy from the document glass. (14) Side cover Open to remove misfed paper. (15) Side cover handle Pull to open the side cover. (16) Bypass tray guides Adjust to the width of the paper when using the bypass tray.
BEFORE USING THE PRODUCT OPERATION PANEL Keys for fax function (when the fax option is installed) These are used in fax mode. For more information, see the "Operation manual (for facsimile)" that accompanies the optional facsimile expansion kit. [COPY] key / indicator Press to select copy mode.
Page 17
PAPER SELECT COPY RATIO AUTO IMAGE OUTPUT 2-SIDED COPY RESOLUTION ADDRESS FORMAT ORIGINAL SIZE DUPLEX SCAN RESOLUTION ADDRESS BROADCAST ORIGINAL SIZE DUPLEX SCAN (16) (17) (18) (19) (20) (13) [FAX] key / indicator (when the fax option is installed) LINE indicator, DATA indicator This key is used in fax mode.
Example: Copy mode Ready to copy. AUTO 100% AUTO * The display shown is the MX-M200D (when the optional RSPF is installed) display. Exposure display Indicates the selected exposure mode. Special function icon display Icons of enabled special functions will appear.
TURNING THE POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON Turn the power switch to the "ON" position • It will take about 45 seconds for the machine to warm up. •...
Ready to copy. AUTO 100% *The screen is that of the MX-M200D. AUTO LOADING PAPER The message "TRAY< >:Add paper." will be displayed when there is no copy paper in the selected paper tray. (< > is the tray number.) Load paper in the indicated paper tray.
• There are many varieties of special paper available on the market, and some cannot be used with this machine. Before using special paper, contact your authorised service representative. • Before using other than SHARP recommended paper, make a test copy to see if the paper is suitable. LOADING PAPER Make sure that the machine is not copying or printing, and then follow these steps to load paper.
• When loading envelopes, make sure that they are straight and flat and do not have loosely glued construction flaps (not the closure flap). • Special papers except SHARP recommended transparency film, labels, and envelopes must be fed one sheet at a time through the bypass tray.
CHANGING THE PAPER SIZE SETTING OF A TRAY If the size of the loaded paper is different from the size shown in the display, follow the steps below to change the paper size setting of the tray. The paper size setting cannot be changed during copying, printing, fax printing (when the fax option is installed), or interrupt copying, or when a misfeed has occurred.
BEFORE USING THE PRODUCT DISABLING (ENABLING) AUTO TRAY SWITCHING When auto tray switching is enabled and paper runs out during copying or printing, the job will continue using paper from a different tray if that tray has the same size of paper in the same orientation. (This function does not operate when using the bypass tray or when a fax is being printed.) This function has been enabled at the factory.
AUDITING MODE When auditing mode is enabled, a count is kept of the pages printed by each account. The page counts can be viewed in the display. This function is enabled in the system settings. (For the counts in copy, print, and scan modes, see page 79. For the counts in fax mode, see the "Operation manual (for facsimile)"...
TROUBLESHOOTING AND MAINTENANCE This chapter explains general troubleshooting and maintenance procedures such as removing misfeeds, replacing the toner cartridge, and cleaning the machine, as well as troubleshooting for the copy function. For troubleshooting for the fax function, printer function, and scanner function, see the respective manuals for each function. TROUBLESHOOTING MACHINE/COPYING PROBLEMS The machine does not operate.
Blank copies " appears in the display, turn off the power switch, wait about 10 seconds, above. When you contact your Sharp dealer, please tell your dealer Cause and solution The power cord is not plugged into a power outlet.
TROUBLESHOOTING AND MAINTENANCE Problem The paper size used for the copy is different from the selected paper size (part of the image is cut off or too much of the page is blank). Wrinkles appear in the paper or the image disappears in places.
Problem Was the SPF (or document cover) opened completely when the original was placed on the document glass? → Open the SPF completely and then place the original on the document glass. The original is curled or folded. → The original size cannot be correctly detected if the original is curled or The original has many solid black areas.
INDICATORS AND DISPLAY MESSAGES If one of the following messages appears in the display, take prompt action as instructed by the message. Message (Maintenance icon) (Developer replacement required icon) Maintenance required. Call for service. Call for service. – (Toner cartridge replacement required icon) Check the toner cartridge.
First check the misfeed location. (Page 31) (Page 33) (Page 34) * The illustration shows misfeed locations in the MX-M200D. ORIGINAL MISFEED IN THE SPF Remove the misfed original. Check sections A, B, and C in the left shows the...
TROUBLESHOOTING AND MAINTENANCE Section C Remove the misfed original from the exit area. If the misfed original cannot be easily removed from the exit area, open the moveable part of the document feeder tray and remove the original. MISFEED IN THE BYPASS TRAY Carefully remove the misfed paper from the bypass tray.
MISFEED IN THE MACHINE To remove a paper misfeed from the machine, the bypass tray and then the side cover must be opened. Check whether the misfeed occurred in A, B, or C below and then follow the misfeed removal procedure for that location. Open the bypass tray and then the side cover.
Page 34
TROUBLESHOOTING AND MAINTENANCE Misfeed in B Open the front cover. Push gently on both ends of the front cover. Turn the roller rotating knob in the direction of the arrow. Roller rotating knob Lower the right and left fusing unit release levers and remove the misfed paper.
Misfeed in C Lower (1) in the illustration, open the fusing unit paper guide, and remove the misfed paper. Be careful not to tear the misfed paper during removal. The fusing unit is hot. Do not touch Warning the fusing unit when removing misfed paper.
TROUBLESHOOTING AND MAINTENANCE MISFEED IN TRAY 2 • Make sure that there is no misfed paper in the tray before pulling it out. (Page 31) Note • Also use the following procedure to remove misfeeds that occur in the 250-sheet paper feed unit and the 2 x 250-sheet paper feed unit.
REPLACING THE TONER CARTRIDGE When the toner replacement icon ( When the message " Add toner. Can not copy or print." appears in the display, the toner cartridge must be replaced before copying can be resumed. Follow the steps below to replace the toner cartridge. •...
CHECKING THE TOTAL OUTPUT COUNT To check the total number of pages output in copy, print, and fax modes and the total scan count in scanner mode, hold down the [COPY] key when the machine is in the standby state. The counts will appear while the key is held down. The total output count and the total scan count can be used as a guideline for cleaning.
CLEANING THE MACHINE CLEANING THE DOCUMENT GLASS AND SPF/DOCUMENT COVER If the document glass, SPF, underside of the document cover, or the scanner for originals coming from SPF (A) (the long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep these parts clean.
TROUBLESHOOTING AND MAINTENANCE CLEANING THE TRANSFER CHARGER If white or black lines appear in copies or the image is blotchy, the transfer charger may be dirty. Follow the steps below to clean the charger. Turn the power switch off. Open the bypass tray and the side cover.
ADJUSTING THE DISPLAY CONTRAST The contrast of the display can be adjusted as explained below. Press the [SPECIAL FUNCTION] key. ON LINE SPECIAL FUNCTION DATA SPECIAL SPECIAL MODES FUNCTION ORIG. SIZE ENTER PAPER SIZE SET LINE COPY EXPOSURE PAPER SE DATA SCAN COLOUR MODE...
OPTIONAL EQUIPMENT Convenient optional equipment can be installed on the machine as needed. • As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification Note changes for product improvement without prior notice.
Detectable original sizes (5-1/2" x 8-1/2"* When installed on MX-M160D: 16 pages/min. Original exchange speed* When installed on MX-M200D: 20 pages/min. Weight 5.3 kg (11.7 lbs.) Dimensions 586 mm (W) x 440 mm (D) x 132 mm (H) (23-5/64" (W) x 17-21/64" (D) x 5-13/64" (H)) *1 Two-sided scanning is not possible.
Standard supplies for this product that are to be replaced by the user are paper and toner cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers.
COPY FUNCTIONS This chapter explains the basic procedures for making copies, including selection of the copy ratio and other copy settings. NORMAL COPYING This section explains how to make a regular copy. If "Auditing mode" has been enabled (page 23), enter your 5-digit account number. Copying from the document glass Open the SPF and place the original face down on the document glass.
COPY FUNCTIONS Press the [START] key ( copying. The copy will be delivered to the centre tray. WXYZ @.- _ AD-END Copying from the SPF Open the SPF and make sure that an original has not been left on the document glass.
Page 49
Auto paper select mode When auto paper select mode is enabled, "AUTO" appears in the paper size display. This function automatically selects paper that is the same size as the original (A5, B5, B5R, A4, A4R, B4, A3, 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2"...
COPY FUNCTIONS MAKING A COPY DARKER OR LIGHTER The copy exposure can be adjusted as needed to the original. Three exposure modes are available: "AUTO", "TEXT" and "PHOTO". When "TEXT" or "PHOTO" is selected, the exposure can be manually adjusted to 5 levels. Auto This is the default exposure mode.
SELECTING THE TRAY By default the auto paper select function (page 47) operates, and thus the appropriate tray is automatically selected when the original is placed on the document glass or in the document feeder tray, or when the original size is specified.
COPY FUNCTIONS SELECTING THE ORIGINAL SIZE If you loaded a non-standard size* original or the original size was not correctly detected, set the original size manually. Perform the following steps after placing the document in the document feeder tray or on the document glass. * Standard sizes: Note The following sizes can be detected correctly: A3, B4, A4, A4R, A5 (11"...
USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL When the bypass tray is being used for copying and an original that is placed on the document glass is detected as being a special size, the display will prompt the user to set the original size. To make a copy in this type of situation, follow the steps below.
REDUCING OR ENLARGING A COPY There are three ways to enlarge and reduce copies: • Automatic selection of a ratio according to the paper size: Auto ratio selection • Specifying a ratio from 25% to 400%: Preset ratios/zoom • Selecting the vertical and horizontal ratios separately: XY zoom When the SPF is being used, the zoom copy ratio range is 50% to 200%.
Page 55
Select a preset ratio with the [ ] or [ ] key, or set the ratio (zoom) with the [ ] or [ ] key. ED COPY LEX SCAN LEX SCAN ] key: Select a larger preset ratio ] key: Select a smaller preset ratio ] key: Decrease the ratio in increments of 1% ] key: Increase the ratio in increments of 1% •...
SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY Separate ratio settings can be selected for the length and width of a copy. Example: Reduction only in the horizontal direction • This feature cannot be used with the 2 in 1 / 4 in 1 feature or card shot feature. •...
Page 57
Press the key. XY ZOOM 115% 100% READ ACC. #-C [ ]:X Y The vertical ratio can now be selected. Set the vertical ratio with the [ ], [ ], [ ], or [ ] keys. A preset ratio can be selected with the [ ] or [ ratio can be adjusted in...
TWO-SIDED COPYING TWO-SIDED COPYING The machine is capable of the following types of automatic two-sided copying. The copy paper is turned over automatically, allowing two-sided copying to be accomplished with ease. Document glass One-sided original RSPF • There are restrictions on the paper that can be used for automatic two-sided copying. See "Paper that can be Note used for automatic 2-sided printing"...
TWO-SIDED COPYING OF ONE-SIDED ORIGINALS • Paper sizes that can be used are A3, B4, A4, A4R, B5, B5R, A5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11" and 8-1/2" x 11"R. • Automatic two-sided copying is not possible when the bypass tray is used. Copying from the SPF Make sure that an original does not remain on the document glass, and...
COPY FUNCTIONS Copying from the document glass Place the original for the front side of the copy on the document glass, and close the SPF. Press the [2-SIDED COPY] key. COPY MODE OUTPUT 2-SIDED COPY ORIGINAL SIZE DUPLEX SCAN 1 to 1 ORIGINAL SIZE DUPLEX SCAN 1 to 2...
TWO-SIDED COPIES OF TWO-SIDED ORIGINALS (ONLY WHEN USING THE RSPF) • Paper sizes that can be used are A3, B4, A4, A4R, B5, B5R, A5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11" and 8-1/2" x 11"R. •...
COPY FUNCTIONS ONE-SIDED COPIES OF TWO-SIDED ORIGINALS (ONLY WHEN USING THE RSPF) • Paper sizes that can be used are A3, B4, A4, A4R, B5, B5R, A5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11" and 8-1/2" x 11"R. •...
TWO-SIDED COPIES USING THE BYPASS TRAY Follow the steps below to perform two-sided copying manually. Example: Copying original A and original B onto both sides of the paper Copy original A. Copy of Original A original A Copy of Original A original A Place original B as shown below.
DUAL PAGE COPY The dual page copy function produces separate copies of open bound original pages. This function is convenient when you wish to make a separate copy of each page of a book or other bound document. • A4 (8-1/2" x 11") paper can be used for dual page copying. Note •...
INTERRUPTING A COPY RUN A copy run can be temporarily interrupted to allow another copy job to be performed. (Interrupt copying) When the other job is finished, the copy run will resume using the original copy settings. • Interrupt copying is not possible when the document glass is being used for a copy job and "NO SORT" is selected.
CONVENIENT COPY FUNCTIONS Select convenient copy functions after pressing the [COPY] key to select copy mode. ROTATING THE IMAGE 90 DEGREES When "Auto paper select mode" or "automatic ratio selection" are in operation and the original is placed in a different orientation (vertical or horizontal) from the paper, the original image will be automatically rotated 90 degrees to enable correct copying onto the paper.
Place the originals in the document feeder tray or the first original on the document glass. If the originals are placed in the document feeder tray, sort mode will be automatically selected. This can be changed to no sort in the system settings. (Page 87) If the first original is placed on the document glass, no sort mode will be automatically selected.
COPYING MULTIPLE ORIGINALS ONTO A SINGLE SHEET OF PAPER Multiple originals can be copied onto a single sheet of paper in a selected layout. This function is convenient when you wish to present multiple pages in a compact format, or show a view of all pages in a document.
Page 69
Select "2in1/4in1" with the [ ] or [ ] key. SPECIAL MODES DUAL PAGE COPY 2in1/4in1 ED COPY LEX SCAN XY ZOOM LEX SCAN [OK]:CHANGE Press the [OK] key. 2in1/4in1 2in1 4in1 [OK]:CHANGE The 2 in 1 / 4 in 1 selection screen will appear.
CREATING MARGINS WHEN COPYING The margin shift function shifts the image to create a margin at the edge of the paper. By default the function creates a 10 mm (1/2") margin at the left edge of the paper. Original • You can select whether to create a margin at the top edge or at the left edge of the paper. •...
ERASING SHADOWS AROUND THE EDGES OF A COPY This feature is used to erase shadows that appear around the edges of copies of books and other thick originals. (Edge erase) The feature can also erase the shadow that appears down the centre of books and other originals that open up. (Centre erase) Both the shadow lines around the edges of copies and the shadow at the centre can be erased.
Page 72
CONVENIENT COPY FUNCTIONS Select the erasure width with the [ ] or [ ] key. If you select 0 mm (0"), the printed result is the same as when "OFF" is selected. Press the [OK] key. You will return to the base screen.
CARD SHOT When copying a card, this function allows you to print the front and back sides of the card next to each other on a single sheet of paper. This function creates 2 in 1 images of the front and back side of the card and centres them on the paper. Original CARD Front of...
Page 74
CONVENIENT COPY FUNCTIONS Press the [START] key ( The front side of the card is scanned. WXYZ @.- _ AD-END Turn the original over on the document glass. Press the [START] key ( Copying will start after both sides of the original have been scanned.
Paper fed from tray 1 on machine, A4 (8-1/2" x 11") original and paper oriented horizontally, no reduction or enlargement.) *2 May vary depending on machine operating conditions and ambient conditions such as power voltage and humidity. Digital Multifunctional System MX-M200D A3 (11" x 17") 10 copies/min.
Page 76
APPENDIX Overall dimensions 590 mm (W) x 574 mm (D) (23-15/64" (W) x 22-38/64" (D)) Weight (Not including MX-M160D: toner cartridge) MX-M200D: Dimensions MX-M160D: MX-M200D: Operating conditions Temperature: 15°C to 30°C (59°F to 86°F), Humidity: 20% to 85% Noise level Sound Power Level L Copying: 6.3[B] or less...
SYSTEM SETTINGS GUIDE PURPOSE OF THE SYSTEM SETTINGS The system settings are used by the administrator of the machine to enable or disable functions to suit the needs of your workplace. This manual explains only the system settings that are common to all the functions of the machine, (copy, fax, printer and network scanner functions), as well as system settings that are specifically for the copy function.
PROGRAMMING AN ADMINISTRATOR PASSWORD Press the [SPECIAL FUNCTION] key. ON LINE SPECIAL FUNCTION DATA SPECIAL SPECIAL MODES FUNCTION ORIG. SIZE ENTER PAPER SIZE SET LINE COPY EXPOSURE PAPER SE DATA SCAN COLOUR MODE RESOLUT DISPLAY CONTRAST The special function screen will appear. Select "SYSTEM SETTINGS"...
SYSTEM SETTINGS LIST A list of basic programs used for the machine and a list of programs used for the copy function are shown below. Programs for general use of the machine Program name ADMINISTRATOR PASSWORD CHANGE ADMINISTRATOR PASSWORD CHANGE ACCOUNT CONTROL AUDITING MODE TOTAL/ACCOUNT...
USING THE SYSTEM SETTINGS Press the [SPECIAL FUNCTION] key. ON LINE SPECIAL FUNCTION DATA SPECIAL SPECIAL MODES FUNCTION ORIG. SIZE ENTER PAPER SIZE SET LINE COPY EXPOSURE PAPER SE DATA SCAN COLOUR MODE RESOLUT DISPLAY CONTRAST The special function screen will appear. Select "SYSTEM SETTINGS"...
ACCOUNT CONTROL These programs are used to control use of the machine by account. To access one of these programs, select "ACCOUNT CONTROL" in the mode selection screen, select the desired program in the account control screen, and press the [OK] key. AUDITING MODE This program is used to enable auditing mode for copy, print, and scan mode.
SYSTEM SETTINGS GUIDE Resetting a single account Select "RESET 1 ACC." with the [ ] or [ ] key and then press the [OK] key. Select the desired account with the [ ] or [ ] key. If "---,---" appears for a page limit, a limit has not been set.
ACCOUNT LIMIT This program is used to set limits for the number of pages that can be printed by each account in print mode and copy mode. Select "ACCOUNT LIMIT" and press the [OK] key. The following screen appears. ACCOUNT LIMIT SINGLE ACC.
SYSTEM SETTINGS GUIDE DEVICE CONTROL These programs are used to configure settings for hardware functions of the machine. To access one of these programs, select "DEVICE CONTROL" in the mode selection screen, select the desired program in the device control screen, and press the [OK] key. WAITING COPY LAMP SETTING This program is used to select whether the copy lamp (light source) is on or off when the machine is in standby...
System requirements for USB 2.0 (Hi-Speed mode) The USB port on the machine supports USB 2.0 Hi-Speed mode. The following system is required to use USB 2.0 (Hi-Speed mode): The computer is running Windows Vista/XP/2000 and the Microsoft USB 2.0 driver is pre-installed, or the USB 2.0 driver for Windows Vista/XP/2000 that Microsoft provides through Windows Update is installed.
SYSTEM SETTINGS GUIDE Select "MESSAGE TIME" and press the [OK] key. The following screen will appear. MESSAGE TIME SHORT (3 sec.) NORMAL (6 sec.) LONG (9 sec.) Select the desired display time with the [ ] or [ ] key. Press the [OK] key.
To enable the setting, select "DISABLE PAPER SIZE SET" and press the [OK] key so that a checkmark appears in the checkbox. To disable the setting, select "DISABLE PAPER SIZE SET" once again and press the [OK] key so that the checkmark is cleared from the checkbox. ENERGY SAVE These programs are used to configure energy saving settings.
SYSTEM SETTINGS GUIDE COPY SETTINGS These programs are used to enable various copy functions. To access one of these programs, select "COPIER" in the mode selection screen, select the desired program in the copy settings screen, and press the [OK] key. EXPOSURE ADJUST This program is used to adjust the exposure level when "AUTO"...
Select "DEFAULT TRAY SET" and press the [OK] key. The following screen will appear. DEFAULT TRAY SET TRAY 1 TRAY 2 TRAY 3 TRAY 4 Select the tray with the [ ] or [ ] key. Press the [OK] key. DEFAULT EXPOSURE This program is used to select the exposure mode/level that is initially selected when the...
[EXPOSURE] key for a copy job. Select "PATTERN 1" or "PATTERN 2" for the method of expressing halftones. "PATTERN 1" is recommended for printed photos, providing sharp images and good expression of outlines. "PATTERN 2" is recommended for photos on photographic paper, providing a soft image.
Telephone number for information Emergency telephone number Sharp Electronics of Canada Ltd. Telephone number for information Emergency telephone number Sharp Corporation of Australia PTY. Ltd. No1 Huntingwood Drive Huntingwood Blacktown N.S.W. Telephone number for information Sharp Electronics (Europe) GMBH Sonninstrasse 3, 20097 Hamburg...
Page 92
MATERIAL SAFETY DATA SHEET 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
Page 93
MATERIAL SAFETY DATA SHEET Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 9.PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical State : Solid Boiling / Melting Point Softening Point(°C) Flash Point(°C) lgnition Point(°C ) Explosion Properties Density(g/cm³)
Page 94
MATERIAL SAFETY DATA SHEET Chronic Effect : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle (4mg/m exposure group, the most relevant level to potential human exposures.
Page 95
Telephone number for information Emergency telephone number Sharp Electronics of Canada Ltd. Telephone number for information Emergency telephone number Sharp Corporation of Australia PTY. Ltd. No1 Huntingwood Drive Huntingwood Blacktown N.S.W. Telephone number for information Sharp Electronics (Europe) GMBH Sonninstrasse 3, 20097 Hamburg...
Page 96
MATERIAL SAFETY DATA SHEET 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
Page 97
MATERIAL SAFETY DATA SHEET Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 9.PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical State : Solid Boiling / Melting Point Flash Point(°C) lgnition Point(°C ) Explosion Properties Density(g/cm³) Solubility in Water...
Page 98
MATERIAL SAFETY DATA SHEET Chronic Effect : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle (4mg/m exposure group, the most relevant level to potential human exposures.
INDEX Symbols / Numbers ] key ...15 2 in 1 / 4 in 1 copy ...66 250-sheet paper feed unit / 2 x 250-sheet paper feed unit ...41 [2-SIDED COPY] key ...15 2-sided printing...18 [ACC.#-C] key ...15, 23 Administrator password...75 Arrow keys ...15 Auditing mode ...23 Auto clear ...17, 46, 83...
Page 100
LINE indicator...15 Loading paper ...18 Loading paper in the bypass tray ...20 Main features ...10 Maintenance icon ...28 Manuals provided with the product ...9 Margin shift...68 Message...28 Misfeed removal...29 - Bypass tray ...30 - In the machine ...31 - SPF ...29 - Tray 1 ...33 - Tray 2 ...34 Normal copying...
Page 101
Convenient copy functions 2 in 1 / 4 in 1 copy ...66 Card shot...71 Erase copy ...69 Margin shift...68 Rotation copy ...64 Sort mode...64 Copying Automatic ratio selection ...52 Dual page copy ...62 Interrupt copying ...63 Making a copy darker or lighter...48 Manual ratio selection (preset copy ratios/zoom)...52 Normal copying - Copying from the document glass ...45...
ADMINISTRATOR PASSWORD NUMBER: FACTORY SETTING The following is the factory setting of the Administrator Password Number, which must be used to access the System Settings. Factory setting = 00000 This number must be entered when accessing the System Settings for the first time. (Page 76) •...
Page 106
If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling.
Page 107
Notice for Users in Europe SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg...
Page 108
MX-M160D/MX-M200D PRINTED IN FRANCE TINSE1976TSZZ...