Table of Contents
Advertisement
Quick Links
Operating Instructions
EMAX designs and manufactures products for safe
operation. However, operators and maintenance per-
sons are responsible for maintaining safety. All safety
precautions are included to provide a guideline for
minimizing the possibility of accidents and property
damage while equipment is in operation.
Keep these instructions for reference.
Stationary Air Compressor
Model # :
UPC:
HI05V08Y1 / HS05V08Y1
815002014265 / 815002014272
EMAX Compressor
1000 Cass Dr., Clayton, OH 45315 USA
866.294.4153
info@emaxcompressor.com
Fax: (937) 540-1157
HI05V08Y1/HS05V08Y1 man
v.190811
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Emax HULK POWER HI05V08Y1
Summary of Contents for Emax HULK POWER HI05V08Y1
- Page 1 Operating Instructions EMAX designs and manufactures products for safe operation. However, operators and maintenance per- sons are responsible for maintaining safety. All safety precautions are included to provide a guideline for minimizing the possibility of accidents and property damage while equipment is in operation.
-
Page 2: Table Of Contents
HULK Power READ INSTRUCTION MANUAL BEFORE OPERATING. In order to receive maximum performance and long life from your compressor, the following instructions should be read carefully and all points regarding installation and operation of the unit should be noted and observed. -
Page 3: Inspection
Stationary Air Compressor Inspection ● Inspect compressor prior to any use. ● Check for external damage that might have occurred during transit. Check for possible damage from transit and test the pulley by turning it freely with your hands. Be careful of moving parts. ●... -
Page 4: Safety Information
HULK Power of excessive pressure build up. The safety valve is preset at factory. Do not attempt to make any adjustments to the safety valve. Periodically pull the ring on the safety valve end to check that it is working properly. 5. -
Page 5: Basic Guidelines
This product or its power cord simultaneously used, existing warranties are may contain chemicals known to void, and EMAX Air Force Technology disclaims the State of California to cause cancer and birth any liability whatsoever for any loss, personal defects or other reproductive harm. Wash hands injury or damage. -
Page 6: Installation
HULK Power safety glasses. Everyday eyeglasses are NOT Electrical Safety safety glasses. Dust mask, non-skid safety Be sure only trained and shoes, hard hat, or hearing protection should authorized personnel maintain be used in appropriate conditions. this compressor in accordance with all applicable federal, state 2. -
Page 7: Operation
Stationary Air Compressor 13. Always disconnect the tool from power source Keep all persons away from the before making any adjustments, storing, discharge opening of hoses or servicing, or changing accessories. Such tools or other points of preventative safety measures reduce the risk compressed air discharge. -
Page 8: Getting Started
HULK Power 2. Make sure all hose connections are current (AC) power source. If connected to a circuit adequately secured to prevent tools or hose protected by fuses, use time-delay fuse marked “D”. ends from being accidentally disconnected. Installation should be executed by a licensed electrician who should verify the ACTUAL VOLTAGE 3. -
Page 9: General Overview
Stationary Air Compressor check that all pipes and hoses are firmly connected. Keep unit level and be ● Do not use the air compressor if any damage is found. If damaged, have an authorized service careful of top-heavy load center inspect and test the air compressor to ensure that is working properly. -
Page 10: Starting
● Drain Valve: Make sure the tank drainage valve is void. closed and not in the open position. ● Use only EMAX approved oils in your Pressure Switch compressor, or your warranty is void. ● Ensure that the power supply you are going to DO NOT use automotive-type oil. -
Page 11: Daily
Stationary Air Compressor Troubleshooting Daily ● Before each use, Always inspect the compressor before use, and 1. check for any unusual noise or vibration. make sure it is in good working condition. Make sure all air vents are clear. Check the power cable 2. -
Page 12: Overheating
HULK Power Overheating Storage Compression of air generates heat, much of which is When storing your compressor: dissipated as air passes over the intercooler and/or 1. Be sure the unit is turned OFF. after cooler. 2. Remove it from power source. Overheating can be caused by: 3. -
Page 13: Troubleshooting Chart
Stationary Air Compressor Troubleshooting Chart Trouble Possible Cause Corrective Action Compressor will not start 1. Blown fuse or circuit breaker 1. Replace or reset fuse/circuit breaker tripped 2. Loose electrical connections 2. Check wiring connnections Low pressure 1. Restricted air filter 1. -
Page 14: Hulk Warranty Statement
Use only EMAX-approved oils in your compressor, or your warranty is void. ● Extended warranty: Hulk Power by EMAX will extend your 1-year warranty by 3 years, for a total of 4 years of warranty coverage when you opt to register for the extended warranty plan.