I-Size_Base_009; I-Size_Base_008; Basic Instructions - TAKATA I-SIZE BASE Instructions Manual

new TAKATA I-SIZE BASE. Accidents can cause
damage to the TAKATA MINI I-SIZE or TAKATA
MIDI I-SIZE seat and the TAKATA I-SIZE BASE that
may not be visible to the naked eye. Failure to observe
this notice may seriously risk your child's safety in the
event of an accident.
[I-SIZE_BASE_006] The TAKATA I-SIZE BASE can
heat up when placed in direct sunlight. To prevent
burns, ensure that an adult checks all plastic and metal
parts of the TAKATA I-SIZE BASE before use.
[I-SIZE_BASE_007] Position the TAKATA I-SIZE
BASE so that static parts (plastic elements, etc.) do
not get stuck in vehicle doors during normal use of the
vehicle.
[I-SIZE_BASE_008] Do not leave any sharp, pointy
or heavy objects around the vehicle. In the case of an
DFFLGHQW WKHVH REMHFWV PD\ À\ DURXQG WKH FDELQ
injuring children or other passengers. Luggage and
other potentially dangerous items should also be
secured in place.
Never leave the TAKATA I-SIZE BASE with your
child in the TAKATA MINI I-SIZE or TAKATA MIDI
I-SIZE (whether attended or not) on a raised, slanted
or uneven surface, such as a table, a baby-changing
table, steps or a ramp.
NOTE!
The TAKATA I-SIZE BASE should not be used for
any more than six years after purchase. Plastics
deteriorate generally over time, particularly when
exposed to direct sunlight. This deterioration is not
always visible to the naked eye, and can compromise
the performance of the TAKATA I-SIZE BASE.
Should you have any other queries as to the use of this
product, please contact TAKATA customer services
(see Section 8 – Service).

3. BASIC INSTRUCTIONS

CAUTION!
$OZD\V SODFH WKH 7$.$7$ ,6,=( %$6( RQ D ÀDW
stable surface.
CAUTION!
%H FDUHIXO WKDW \RXU ¿QJHUV DQG RWKHU ERG\ SDUWV GR
not get caught in any moving sections of the seat.
Adjusting the support leg
Step 1 – Fold out the support leg
[I-SIZE_BASE_009 + I-SIZE_BASE_010] Take hold
of the support leg on the underside of the TAKATA
I-SIZE BASE. Push the release slider of the folding
mechanism to the side, pull the support leg out of the
transportation position, and swing it out as far as it
will go. When it reaches full extension, the support leg
is locked into place by a spring in the release slider.
Step 2 – Unlock and adjust the support leg
[I-SIZE_BASE_011] Press the button on the height
adjustment mechanism as far in as possible, and slide
the support leg up or down. When the desired position
is reached, release the button and check that the
support leg is locked in place. This is indicated by a
click, and a green marking on the top of the button.
WARNING!
If the support leg is not set at the correct height, there
is a risk of serious injury to the child or other
passengers in the case of an accident.
[I-SIZE_BASE_022] The correct position of the
support leg is set when the support leg of the TAKATA
,6,=( %$6( OLHV FRPSOHWHO\ DQG ÀXVK DJDLQVW WKH
YHKLFOH ÀRRU DQG WKH LQGLFDWRU DW WKH ORZHU HQG RI WKH
support leg is fully showing a green marking.
Step 3 – Fold in and lock the support leg
[I-SIZE_BASE_009] To be able to fold in the support
OHJ \RX PXVW ¿UVW SRVLWLRQ LW LQ WKH VPDOOHVW KHLJKW VHW-
ting. Push the release slider of the folding mechanism
to the side, and swing the support leg towards the
underside of the base. When the support leg lies snug
against the underside of the TAKATA I-SIZE BASE,
the support leg is locked into place by a spring in the
release slider.
Adjusting the ISOFIX connectors
The two ISOFIX connectors on the TAKATA I-SIZE
BASE must be adjusted, according to the position of
the ISOFIX points in the vehicle. Each of the
connectors can independently be set to one of six
different lengths, with the various settings indicated by
¿JXUHV  WR  RQ WKH WRS RI WKHP 6HWWLQJ VL[ LV
obtained when the connectors are at full extension,
DQG LV LQGLFDWHG E\ WKH DEVHQFH RI DQ\ ¿JXUH
Step 1 – Unlock the ISOFIX length adjuster
[I-SIZE_BASE_012] Press the left-hand button on the
ISOFIX length adjuster as far in as possible and hold
de
en
fr
it
es
nl
17