Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PR Lighting AQUA MARINE 580 BWS
Summary of Contents for PR Lighting AQUA MARINE 580 BWS
- Page 1 AQUA MARINE 580 BWS PR-2596 The user manual contains important information about the safe installation and use of a projector. Please read and follow these instructions carefully and keep the manual in a safe place for future reference.
-
Page 2: Table Of Contents
INDEX ………………………………………………………………………………… SAFETY AND WARNINGS ……………………………………………………………………………………………… APPEARANCE …………………………………………………………………………………………… INSTRUCTIONS …………………………………………………………………………………………… INSTALLATION …………………………………………………………………………… SETUP AND CONFIGURATION ………………………………………………………………………………………… OPERATION MENU …………………………………………………………………………………………… DMX PROTOCOL ………………………………………………………………………… SIGNS ON THE TOUCH SCREEN 9. ERROR MESSAGES……………………………………………………………………………………… ………………………………………………………………………………………… TECHNICAL DATA ………………………………………………………… CIRCUIT DIAGRAM AND PCB CONNECTIONS …………………………………………………………………………… COMPONENT ORDER CODES ACCESSORIES The following items are supplied with the projector and please check:... -
Page 3: Safety And Warnings
1. SAFETY AND WARNINGS NOTE Before a projector’s installation, power-on, operation and maintenance, please carefully read the safety information hereinafter! The following safety signs are used in the user manual. User Electrical Protective High Warning Flames Goggles Manual shock Gloves Temperature When unpacking , check if there is transportation damage before using the projector. -
Page 4: Appearance
There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety ● cord supplied through the safety cord holes for safety support. Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from ●... - Page 5 TROUBLESHOOTING ● PROBLEM ACTION Check the fuse on the power socket. The projector doesn’t switch on Check the lamp. The lamp is on but the projector doesn’t respond Make sure that the fixture’s start address is right ...
-
Page 6: Installation
4. INSTALLATION RIGGING ● Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a projector with power while it is locked. Clamp Safety Cord Handle Warming Please run the safety cord through the two safety cord holes. - Page 7 The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in ● accordance with the standards concerned. If any questions about the electrical installation, do not continue but consult a qualified electrician. ● DMX CONTROL CONNECTION: ●...
- Page 8 DMX TERMINATOR CONNECTION Connect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain. PIN 2 PIN 3 ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP ● Please hold the projector well before adjustment/installation/replacement of a lamp.
-
Page 9: Setup And Configuration
GOBO REPLACEMENT ● Replacement of the Gobos: Open the chamber cover after loosening 4 screws. Select the rotator for replacement of gobo. Push the rotator at the opposite side of its gear till it is off the holder of the rotating gobo wheel. Remove the rotator gently . - Page 10 for the DMX address desired. Press or DOWN key Press ENTER key to confirm. Press the FUNC key to go back to the upper level menu. DMX WIRELESS CONTROL ● The projector has wireless control function with wireless receiver module and antenna for remote control. The setup of it is below: 1.
-
Page 11: Operation Menu
6. OPERATION MENU 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL LEVEL 1-512 DMX Address Default IP Address 2.X.X.X /10.X.X.X IP Address Custom IP Address X.X.X.X Address SubNet Mask X.X.X.X ArtNet Universe 0-255 Really Reset? Total Reset Confirm or Cancel Really Reset? Pan&Tilt Reset Confirm or Cancel... - Page 12 Wireless In/XLR Out ARTNET Only ARTNET In/XLR Out Normal time out Loss of DMX Hold Last Value Off After Delay Display Mode On Always Invert OFF Display Config Display Invert Invert ON Invert Auto English\Chinese Language Setting Celsius Degree Temperature Unit Fahrenheit Degree Un-Link Wireless Really Un-Link?
- Page 13 Zoom Invert OFF/ ON CYM Invert OFF/ ON Restore Defaults? Defaults Confirm or Cancel Channel Value Strobe Dimmer Dimmer Fine CYM Macro Cyan Yellow Magenta Color Wheel Color Wheel Fine XXX Fixed Gobo Wheel XXX Rot. Gobo Wheel XXX Rot. Gobo Rotation XXX Rot.
- Page 14 Lamp Fan2 xxx on/off Strobe Fan xxx on/off Gobo Fan xxx on/off Lamp T Fan xxx on/off Lamp R Fan2 xxx on/off Head Fan xxx on/off Value Lamp Fan1 Lamp Fan2 Lamp T Fan Lamp R Fan Fan Error Head Fan1 Head Fan2 CYM Fan Gobo Fam...
- Page 15 … Change Operation Mode? DMX Mode Confirm or Cancel Change Operation Mode? Preset Memory Confirm or Cancel Change Operation Mode? Master Mode User Memory 1 Confirm or Cancel Change Operation Mode? User Memory 2 Confirm or Cancel Change Operation Mode? Preset Memory Confirm or Cancel Operation...
-
Page 16: Dmx Protocol
Link to Step XXX Strobe XXX Dimmer XXX Dimmer Fine XXX CYM Macro XXX Cyan XXX Cyan Fine XXX Edit Static Scene Yellow XXX Yellow Fine XXX Magenta XXX Magenta Fine XXX CTO XXX CTO Fine XXX Color Wheel XXX Color Wheel Fine XXX Fixed Gobo Wheel XXX Rot. - Page 17 000-035 Close Dimmer （0-100%） Linear dimming 036-255 000-255 Dimmer Fine Dimmer in 16 bit White 000-016 Yellow+ Magenta=Red 017-035 Yellow 036-054 Yellow +Cyan=Green 055-073 CYM Macro Cyan 074-092 Cyan + Magenta= purple 093-111 112-128 Magenta 129-255 CYM color mixing from slow to fast Cyan Cyan (linear 0~100%) 000-255...
- Page 18 Fixed Gobo 044-050 Gobo6 Wheel 051-059 Gobo7 060-064 Gobo8 065-071 Gobo9 072-078 Gobo10 079-085 Gobo11 086-092 Gobo12 093-099 Gobo13 100-106 Gobo14 107-113 Gobo15 114-120 Gobo16 121-127 Gobo17 128-157 Clockwise rotation from slow to fast 158-187 Anti Clockwise rotation from slow to fast 188-191 Shake effect 1 from slow to fast 192-195...
- Page 19 206-215 Shake of Gobo 3 from slow to fast 216-225 Shake of Gobo 4 from slow to fast 226-235 Shake of Gobo 5 from slow to fast 236-245 Shake of Gobo 6 from slow to fast 246-255 Shake of Gobo 7 from slow to fast 000-128 Gobo Indexing(0~540degrees) Rotation （Clockwise From slow to Fast）...
-
Page 20: Signs On The Touch Screen
000-019 Reserved Keep in the DMX range for more than 5S to activate the following functions. If power-off, the following are invalid. 020-024 Graphic Display On 025-029 Graphic Display Off 030-034 Reserved 035-039 Lamp ECO Power 040-044 Lamp Full Power 045-089 Reserved 090-094... -
Page 21: Error Messages
9. ERROR MESSAGES The system can detect some errors during the reset, if displayed, touch ENTER to view the error. The error messages are as follows: Name Type Correction Timeout/magnet Sensor/Encoder Check if wiring, positioning parts and motors are normal Timeout/magnet Sensor/Encoder Check if wiring, positioning parts and motors are normal Tilt... -
Page 22: Technical Data
10. TECHNICAL DATA ELECTRIC PARAMETERS Input voltages 100V~240V AC，50/60Hz Input Power 800W Current at Maximum 9 A Power factor PF〉0.9 LAMP SPECIFICATIONS PHILIPS MSD Platinum 25 R Lamp 7800 K Color Temperature Manufacturers Rated Lamp Life 1500hours COLORS 1 Color wheel: 12colors+ Open, rainbow effect with bi-directional and variable speeds, Stepping/linear color changing Color 9 Color 10 Color8... - Page 23 INDEPENDENT CTO SYSTEM Linear CTO system FIXED GOBO WHEEL 1 Fixed gobo wheel: 17 gobos +Open Bi-directionally rotatable, and shakable at variable speeds Gobo1 Gobo2 Gobo3 Gobo4 Gobo5 Gobo6 Gobo7 Gobo8 Gobo9 Gobo10 Gobo11 Gobo12 Gobo13 Gobo14 Gobo15 Gobo16 Gobo17 Gobo18 ROTATING GOBO WHEEL 1 Rotating gobo wheel:...
- Page 24 EFFECT WHEEL 1 graphic effect wheel, bi-directional rotation with variable speeds and can be overlapped with fixed gobo wheel and rotating gobo wheel FROST 1pc independent frost filter FOCUS DMX linear focus ZOOM DMX linear zoom DIMMER/STROBE 0-100% Linearly adjustable/ Double shutter blades, 0.3~25 F.P.S HEAD MOVEMENT Pan 540º...
- Page 25 532x548x767 (LXWXH) (Please see the figure below. Measurements with a margin of error, please refer to the actual product) Installation of Base Mounting Plate LIGHT OUTPUT...
-
Page 26: Circuit Diagram And Pcb Connections
Beam/Spot Mode 1905 40° Lux 7618 2.0° Lux 231190 130045 57798 2080712 520178 83228 40° 2.0° Distance (m) Diameter (m) 1.07 0.18 0.89 0.36 0.54 0.72 Diameter (m) 21.53 3.59 17.94 7.18 14.35 10.76 Wash Mode 1290 50° Lux 5161 3°... - Page 28 PCB CONNECTIONS ● 8-Channel SLAVE1 ：P/N230060762 8 Channel Driver Board 1 M1-1 Motor 24V Input M1-2 Motor Reserved M1-3 Motor Reserved M1-4 Motor HALL1-6Magnet Sensor M1-5 Motor HALL1-5 Magnet Sensor M1-6 Motor HALL1-4 Magnet Sensor Reserved HALL1-3 Magnet Sensor Reserved HALL1-2 Magnet Sensor Reserved HALL1-1 Magnet Sensor...
-
Page 29: Component Order Codes
12. COMPONENT ORDER CODES NAME PART NO. QTY. REMARKS STEPPER MOTOR 030040073B STEPPER MOTOR 030040114C STEPPER MOTOR 030040121A STEPPER MOTOR 030040136B STEPPER MOTOR 030040167A STEPPER MOTOR 030040212B STEPPER MOTOR 030040213B STEPPER MOTOR 030040246A STEPPER MOTOR 030040254A STEPPER MOTOR 030040221C STEPPER MOTOR 030040224C STEPPER MOTOR 030040257A... - Page 30 1582 Xingye Avenue, Nancun Panyu Guangzhou, 511442 China TEL: +86-20-3995 2888 PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products. Counterfeiting Will be Prosecuted! P/N:320020957...
Need help?
Do you have a question about the AQUA MARINE 580 BWS and is the answer not in the manual?
Questions and answers