Advertisement
Quick Links
Package Contents
Mount bracket
RJ45 coupler
RJ45 cable
M3 x 10mm pan head screws (4)
T6 Torx security screw
AP-310-MNT-W3 Mounting Template
Introduction
The AP-310-MNT-W3 mount kit offers a secure mounting solution for 310 Series Campus Access Points.
This mount kit attaches to standard single and dual gang wall boxes, or mounts to a flat surface, such as a
wall or ceiling.
The DC power plug and Kensington lock cannot be used with this mount.
This mount is not compatible with large (4.5in x 4.5in) US wiring boxes.
Installing the AP-310-MNT-W3 Mount Kit
!
Failure to properly install the AP-310-MNT-W3 may result in damage to equipment and/or bodily injury.
To install the mount bracket onto a flat surface, see
install the mount bracket onto a wall box, see
mount bracket onto a European wall box, see
Installing the AP-310-MNT-W3 to a Flat Surface
!
Before installing the AP-310-MNT-W3 to any surface, ensure that the surface can support the combined weight of
the mount kit and access point.
1. (Optional) Remove the punch-out panel on the side of the mounting bracket by pressing firmly.
2. Tape the AP-310-MNT-W3 Mounting Template flat onto the desired location, then drill holes at the
points indicated.
0511855-01 |
May 2018
AP-310-MNT-W3 Mount Kit
Installing the AP-310-MNT-W3 to a Flat
Installing the Mount Bracket onto a Wall
Installing the Mount Bracket to a DIN or European Wall
Installation Guide
Surface. To
Box. To install the
Box.
1
Advertisement
Related Manuals for HPE Aruba AP-310-MNT-W3
Summary of Contents for HPE Aruba AP-310-MNT-W3
- Page 1 AP-310-MNT-W3 Mount Kit Installation Guide Package Contents Mount bracket RJ45 coupler RJ45 cable M3 x 10mm pan head screws (4) T6 Torx security screw AP-310-MNT-W3 Mounting Template Introduction The AP-310-MNT-W3 mount kit offers a secure mounting solution for 310 Series Campus Access Points. This mount kit attaches to standard single and dual gang wall boxes, or mounts to a flat surface, such as a wall or ceiling.
- Page 2 3. Once the holes are drilled, remove the template and position the mounting bracket flat against the surface. Align the holes of the mounting bracket with the pre-drilled holes, then screw the housing in place. Screws for step 3 are not provided in this kit. The screw used for this step will vary depending on the surface. 4.
- Page 3 Figure 2 Inserting the RJ45 Cable into the Coupler 6. Connect the opposite end of the RJ45 cable to the ENET port, located on the back of the access point. 7. Once the RJ45 cable is attached, align the pins on the rear panel of the access point with the slots on the mounting bracket.
- Page 4 Installing the Mount Bracket onto a Wall Box 1. Align the holes on the mounting bracket with the corresponding holes on the wall box. To install this kit to a single gang wall box, refer to Figure 4. To install this mount kit to a dual gang wall box, refer to Figure 5.
- Page 5 access pint into the slots. Release the button to secure the access point to the mounting bracket. See Figure Figure 6 Securing the Access Point to the Mounting Bracket 4. To lock the access point to the mounting bracket, insert the T6 Torx security screw into the hole beside the button, located at the bottom of the mount.
- Page 6 Figure 7 Installing the Mounting Bracket to a European Wall Box 2. Route the Ethernet cable through the back of the mount housing, as shown in Figure 7. Connect the cable to the ENET port on the back of the access point. 3.