Important Consideration - Promeba PC-750 Series User Manual

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 07/20
03
OPERATION
03.11 Troubleshooter
COD. ERROR'S DESCRIPTION
1
- VOLTAGE BATTERY IS LESS THAN 3V
- THEY ARE DAMAGED OR DISCONNECTED
2
- VOLTAGE BATTERY IS LESS THAN 34V
3
- THE STRETCHER IS NOT RECEIVE VOLTAGE
FROM AMBULANCE
4
- VOLTAGE BATTERY IS LESS THAN 18V
5 - THE STRETCHER GETS THE VOLTAGE THROU-
GH TERMINAL CONNECTION OF THE SU-
PPORT, BUT THEY HAVE NOT BEEN PRESSED
6
- BATTERIES ARE NOT DETECTED
7
- FAIL IN THE DRIVER OF ENGINE
8
- INTENSITY ABOVE 48V
9
- VOLTAGE IS LESS THAN 15V
10
- FAIL IN CHARGING PROCESS

IMPORTANT CONSIDERATION

- The electrical system of the stretcher will automatically turn off in 15 minutes if there are not make any
operation.
- In manoeuvre of up and down repeatedly to 20 cycles continuosly, you should make a mandatory stop for
at least 15 seconds for electro-hydraulic system of the stretcher recovers.
- It is recommended to remove the two batteries of theirs anchors if the stretcher will spend long periods
of inoperability.
- It is important to maintain a minimum of loading cycles every month to keep the good capacity of the
batteries.
- Not leave without charge the batteries more than 2 MONTHS. It is possible they will stop working.
POSSIBLE CAUSE
- BATTERIES DISCONNECTED
- BATTERIES DAMAGED
- OVERCHARGE DURING THE CHARGING BAT-
TERIES OV
- FAIL CONNECTION STRETCHER-SUPPORT
- AMBULANCE'S BATTERY DISCONNECTED OR
DAMAGED
- POWER CABLES WRONG WAY CONNECTED
BETWEEN SUPPORT AND AMBULANCE
- ONE OF TERMINALS COPPER OF THE STRET-
CHER
- BATTERIES ARE DISCONNECTED
- THE STRETCHER IS NOT PROPERLY ENTERED
IN THE SUPPORT
- FAIL IN MICROSWITCH
- BATTERIES DISCONNECTED
- BATTERIES CONNECTION DAMAGED
- BATTERIES CHARGE VERY LOW
- CONTACT WITH TECHNICAL SERVICE
- STRETCHER WITH OVERLOAD OF WEIGHT
- BATTERIES UNCHARGED
- THE STRETCHER NOT UP/DOWN GENTLY
- STRETCHER WITH OVERLOAD OF WEIGHT
- BATTERIES UNCHARGED
- THE STRETCHER NOT UP/DOWN GENTLY
- CONTACT WITH TECHNICAL SERVICE
POSSIBLE SOLUTION
- BATTERIES PROPERLY CONNECTING
- CHECK CABLE CONNECTION BATTERIES
WITH ELECTRIC PLATE
- REPLACE BATTERIES
- COOL THE BATTERIES DURING 3/4 HOURS
- USE THE CHARGER SUPPLIED BY PROMEBA
- REPLACE BATTERIES FOR NEW ONES
-- CHECK TERMINAL CONNECTION BETWEEN
STRETCHER-SUPPORT
- CHARGE THE BATTERIES OR REPLACE FOR
NEW ONES
- CHECK THE CABLE CONNECTION BETWEEN
STRETCHER-SUPPORT-AMBULANCE
- CHECK TERMINAL CONNECTION OF THE
STRETCHER GOING INTO AND LEAVING THE
ACCOMMODATION
- CHARGE BATTERIES UNTIL ITS MAXIMUM
LEVEL
- ENSURE THE STRETCHER HAS ENTERED
WELL INTO THE SUPPORT AND THE CONNEC-
TION TERMINAL ARE WELL CONENCTED
- CHECK THE STATUS OF MICROSWITCH
- ANCHOR WELL THE BATTERIES TO ITS BASE
- REPLACE FOR NEW BATTERIES
- CHARGE THEM WITH EXTERNAL PROMEBA'S
CHARGER
- CONTACT WITH TECHNICAL SERVICE
- NOT LOAD THE STRETCHER WITH MORE
THAN 300KG
- CHARGE THEM WITH EXTERNAL PROMEBA'S
CHARGER
- SEARCH POSSIBLES SCRATCHS, INTERFEREN-
CE OR LOCKED PIECES IN THE STRETCHER
- NOT LOAD THE STRETCHER WITH MORE
THAN 300KG
- CHARGE THEM WITH EXTERNAL PROMEBA'S
CHARGER
- SEARCH POSSIBLES SCRATCHES, INTERFE-
RENCE OR LOCKED PIECES IN THE STRETCHER
- CONTACT WITH TECHNICAL SERVICE
27