Download Print this page
ELTA FANS Hydor HIT Series Manual

ELTA FANS Hydor HIT Series Manual

Centrifugal in-line fan

Advertisement

Quick Links

HIT Centrifugal In-Line Fan
1.
WARNING
This fan is fitted with a non self-resetting thermal cut-out which switches
the fan off in the event of a fault condition. To reset, turn the power off for one
minute, then back on. Only a suitably qualified and competent person may carry out
maintenance after the electrical supply has been isolated.
CAUTION
In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching device, such as
a timer, or connected to a circuit that is regularly switched on and off by the utility.
WARNING
The appliance can only be used indoors.
2.
General
2.1
It is important these Installation and Maintenance Instructions are fully adhered to.
2.2
Full details of the unit supplied are shown on the product nameplate. If in doubt about any
detail contact Hydor or its agents for clarification.
2.3
All electrical installation must be carried out by suitably qualified and competent
personnel in accordance with all current statutory requirements.
2.4
These instructions cover only the Hydor product and do not include the supply or
installation of any safety equipment that may be required e.g. adequate guarding or
protection from rotating parts and proper electrical isolation.
2.5
Any declarations made by Hydor about product installation and safety, are dependent on
the fan equipment being used within installations which themselves meet the
requirements of the relevant Standards and Directives of your region.
2.6
The fan is designed for use in up to 95% relative humidity. The fan is not suitable for
corrosive or explosive atmospheres.
2.7
The installer should provide easy access to the fan to facilitate future maintenance.
2.8
The installer should ensure the fan is adequately supported.
2.9a The below statement is only applicable to the European market.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2.9b The below statement is only applicable to the non-European market.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
HIT Inst Issue 14: 18.10.17

Advertisement

loading
Need help?

Need help?

Do you have a question about the Hydor HIT Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ELTA FANS Hydor HIT Series

  • Page 1 HIT Centrifugal In-Line Fan WARNING This fan is fitted with a non self-resetting thermal cut-out which switches the fan off in the event of a fault condition. To reset, turn the power off for one minute, then back on. Only a suitably qualified and competent person may carry out maintenance after the electrical supply has been isolated.
  • Page 2: Installation

    2.10 Means for electrical disconnection must be incorporated in the wiring installation in accordance with the relevant wiring and electrical regulations. WARNING The fan must be isolated from the power supply during installation and maintenance. The fan must be earthed in accordance with the local regulations. Refer to the appropriate wiring diagram.
  • Page 3 HIT100, HIT125, HIT150 and HIT160 HIT200, HIT250 and HIT315 Screw bracket side to fan using self tapping Screw bracket side to fan using self tapping screws. (a) screws. (a) Bolt the bracket support/spacer using the button head screws. Bracket side c&d Bracket support/spacer Mounting bracket set (supplied)
  • Page 4 A minimum of 1 metre of duct at least the same diameter as the fan spigots diameter is to be fitted to the fan inlet and discharge spigots. Fans can be pushed directly into the duct and fastened. Make sure the ducting system is not deformed or twisted. For mounting, we recommend using cushioned fast clamps to reduce noise transmission into the ducting system.
  • Page 5 Fan Maintenance Inspection of the fan at least once every 12 months is recommended to ensure that the motor, fan blades, and supporting guards, are clean. Any build up of dust and deposits on the blades or guards should be removed using a non-abrasive cleaner. All fastenings should be checked for tightness.
  • Page 6 Dimensional Data 2-HOLES IN EACH BRACKET SIZES 100-160, O4 SIZES 200-315, O5 AIR FLOW TERM BOX Product Code Weight kg HIT100 HIT125 HIT150 HIT160 HIT200 HIT250 HIT315 Minimum space required for installation HIT Inst Issue 14: 18.10.17...
  • Page 7 Wiring HIT 100 - 125 Switched spur unit BLUE WHITE BLACK WHITE BROWN GREEN/YELLOW 240V 1Ph 50 Hz SUPPLY 220V 1Ph 60 Hz SUPPLY 220-240/1Ph/50-60Hz SUPPLY HIT 150 - 315 Switched spur unit WHITE L3 (LOW) YELLOW L2 (MED) BLUE L1 (HIGH) BLACK WHITE...
  • Page 8 The goods must be inspected by a Hydor official and if necessary returned, with a Returns Note Number, carriage paid, for further examination. Hydor Ltd Hydor Elta Fans (Building Services) Unit 8, Parkers Close, Downton 46 Third Avenue, Pensnett Trading Business Centre, Downton,...

This manual is also suitable for:

Hydor hit100Hydor hit125Hydor hit150Hydor hit160Hydor hit200Hydor hit250 ... Show all