ekwb EK-FB KIT GA-X99 LE Installation And Mounting Manuals

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before through before beginning the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard's circuit board (PCB).
3. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.
4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of Gigabyte GA-X99 LE motherboard
1

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER.
motherboard in order to remove the factory installed MOSFET/NB- as well as SB
cooling solution.
3. APPLYING THERMAL COMPOUND.
Intel X99 PCH
(SB) with electrically non-conductive thermal grease - for example
Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme ™. EKWB recommends to
apply the thermal grease in cross form for the best performance (see sample
picture).
5. PLACING THERMAL PADS ON MOTHERBOARD.
FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION). EK recommends using small drops of electrically non-conductive (for example: Arctic Cooling MX-2
™, MX-4 ™ or GELID GC-Extreme ™) thermal grease on each phase regulator (that is being covered with thermal pad; see picture below) in order to even further improve the
thermal performance of the EK-FB GA-X99 LE series water block.
Place 1.0 mm thick thermal pads in
larger strips over the marked area.

STEP 3: PREPARING YOUR WATER BLOCK

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use.
Installation and mounting manual for EK-FB KIT GA-X99 LE water block
Intel X99 PCH (SB)
Remove all encircled screws on the back of the
Apply thermal compound: lightly coat the
Place the thermal pads you cut on a PCB as shown in the picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL
s
2. CLEANING THE PCB.
Carefully detach the original stock cooler after removing all
screws securing it to the board. Wipe off the remains (by using non-abrasive cloth or
as shown on sample photo) of the original thermal compound until the components and
circuit board are completely clean. EKWB recommends the use of denatured alcohol for
removing TIM leftovers.
4. CUTTING THERMAL PADS.
already pre-cut. Others have to be cut to smaller pieces in order to cover all the VRM
components such as MOSFETs and drivers. PLEASE REMOVE THE PROTECTIVE FOIL
FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.
Replacement thermal pad: Thermal PAD A 1,0 mm - (100 x 16 mm), Thermal PAD A 0,5 mm - (100 x 16 mm)
1: Thermal pad D – 0.5mm
(mosfet):
2: Thermal pad D – 1.0mm
(choke):
1
2
www.ekwb.com
MOSFETs
CPU socket
Your block comes with thermal pads, some of which are
1
2
Place 0.5 mm thick thermal pads in larger strips over the
marked area and make sure all MOSFET chips are
covered.
Revision 1.0. Published on October 30
for updates. Before
qtip ,
st
, 2014