Related Manuals for Triax 157011
Summary of Contents for Triax 157011
- Page 1 LAN Network Tester Part No. 157011 Operating Manual TRIAX - your ultimate connection...
- Page 2 Safety and Disposal The LAN Network Tester operates off 6V DC only. Only use the internal, battery powered, 6V power supply to power the LAN Network Tester. Never connect or use any other power supply to power up the LAN Network Tester otherwise damage to the tester may result or test results could be affected.
-
Page 3: Table Of Contents
Contents Product Overview Features Interface and Key Description Operation Procedures Wiring Diagrams and Test Functions Pair and Length Measurement Coaxial Cable and Telephone Line Measurement Function Calibration and Setup Function Dynamic Calibration Technical Specification... -
Page 4: Product Overview
Product Overview The LAN Network Cable Tester is a powerful tool which can: • Help prevent and solve network cable installation problems. • Check telephony and data cable installations. • Carry out a number of tests such as cable connection sequence, length, user jumper, cable connection continuity and can detect open circuits, short circuits, jumper or cross-talk interference. -
Page 5: Interface And Key Description
Interface and Key Description Power Supply The tester uses 4 x 1.5V size ‘AA’ alkaline batteries with power consumption 16mA (Included). The batteries should be removed if the tester is not used for a long time to prevent the battery pack from leaking which will result in corrosion. (Note disposal advice on page 1). -
Page 6: Operation Procedures
Operation Procedures Start and Display Carries out a self-check, (The dotted line displays the progress of the self-check from left to right). Wait 5 seconds or push any key to display the main menu Main Menu Display There are 4 functions to select from the main menu: Wire Map –... -
Page 7: Wiring Diagrams And Test Functions
Wiring Diagram (WIREMAP) test function: When the wiring diagram, (WIREMAP), test function is selected, the tester will carry out a wiring diagram (WIREMAP) test and displays the following information while the check is being carried out: Test 1: Short Circuit (SHORT) If there is a short circuit on the cable or terminal, it will be shown on the display. - Page 8 Test 3: Normal wiring diagram (WIREMAP) display: The LAN Network Cable Tester will automatically detect the far-end matcher (ID) or local port (L) cable and it will display the wiring diagram (WIREMAP). If it finds the far-end matcher (ID) or the local port (L) on the far-end of the cable being checked, the display will show the following: The ‘R:’...
- Page 9 Test 5: Wiring diagram, (WIREMAP), display when there is an open circuit at the near-end of the cable: The display will show a wiring diagram, (WIREMAP), as shown below if there is an open circuit at the near-end plug. On the ‘M:’ line, pin ‘3’ displays ‘x’, indicating an open circuit towards the near-end plug on pin ‘3’.
-
Page 10: Pair And Length Measurement
Pair and Length measurement (PAIR & LENGTH) function: Whether or not there is a far-end recogniser, (ID), at the far-end of the cable, the LAN Network Cable Tester is capable of carrying out a ‘Pair and Length’ (PAIR & LENGTH) measurement. Therefore, the far-end recogniser, (ID), can remain connected during a wiring diagram, (WIREMAP), and pair and length (PAIR &... - Page 11 Test 2: Normal pair and length (PAIR & LENGTH) display The LAN Network Cable Tester, in ‘Pair and Length’ mode, will display information typical to that shown below when the cable is under normal conditions. It shows the ‘Pair’ line number followed by the cable length. Press the p or q key to restart the test or press the ‘PAIR&L’...
-
Page 12: Coaxial Cable And Telephone Line Measurement Function
It will display an ‘x’ to indicate an open circuit if the length is less than 90% of the other line pair length. In the example shown, the open circuit is located at around 89.7m from the tester. The open circuit line number could be rechecked using the WIREMAP function. -
Page 13: Calibration And Setup Function
Calibration and setup, (SETUP), function: When the Calibration and Setup function is selected, the LAN Network Cable Tester will show a display typical to that shown below: Press the p or q keys to move the cursor ‘->’ indicator up and down to the required item and then press ‘PAIR&L’... - Page 14 Press the p key to select ‘Yes’ and start the measurement. The measured length is displayed as below: Hold the p and q keys (-/+) to display the length adjustment to achieve the actual cable length and then press the ‘PAIR&L’ key to save the calibration factor and exit the calibration function.
-
Page 15: Technical Specification
Technical Specification Overall Dimension 180 x 80 x 40mm. 4 x 1.5V Size AA batteries with power consumption Power Supply 16mA. (Included) Special 4 x 16 character big screen LCD Display lattice (valid visual field 61.6 x 25.2mm). STP/UTP twin twisted cable. Coaxial cable, telephone Type of test Cable line. - Page 16 Issue 2 *Triax reserves the right to change the specifications without prior notification...