Related Manuals for Argon 18 E-117 TRI Disc 317A
Summary of Contents for Argon 18 E-117 TRI Disc 317A
- Page 1 E-117 TRI Disc 317A / 317B : ASSEMBLY GUIDE Valid for MY2020 E-117 Tri Disc 317A / 317B Revision 2.0 - 02.10.2019...
-
Page 2: Table Of Contents
2. E-117 TRI Disc 317A Frameset Parts ........ -
Page 3: Tools Needed & First Aid Kit
1. Tools Needed & First Aid Kit Tools needed for assembly 1: Bearing Cup Press (Park Tool HHP-2) 2: Allen Key Set 3: Grease 4: Utility Pick Set (Park Tool Item # UP-SET) 5: Clean Rags 6: Derailleur Hanger Alignment Gauge (Park Tool Item # DAG-2,2) 7: Cables and Housing Cutter 8: Carbon Paste 9: Loctite #242 or #243... -
Page 4: E-117 Tri Disc 317A Frameset Parts
Not shown on the image: 1.13 - Di2 battery holder - Foam liner for hydraulic hoses 1.3.3 1.8.1 1.3.1 1.8.2 1.3.2 Images are for reference only. Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice. -
Page 5: E-117 Tri Disc 317A Parts' Skus And Descriptions
3. E-117 TRI Disc 317A Parts’ SKUs and Descriptions* Name A18 SKU# E-117 TRI DISC FRAME FRONT DERAILLEUR HANGER (W. SCREWS) 38882 1,3,1 REAR DERAILLEUR HANGER STANDARD 1,3,2 REAR DROPOUT DS 80802 1,3,3 REAR DERAILLEUR HANGER SCREW M4x12 FLAT HEAD... -
Page 6: Seat Post Clamp Installation
4. Seat Post Clamp Installation 5.5 Nm 1. Apply a drop of blue Threadlocker (n. 242) on the bolt’s thread THREADLOCKER BLUE (n. 242) 2. Apply grease on the seat post clamp and on the screws as shown GREASE 3. Assemble the seat post clamp with the small screw, allowing the parts to move freely GREASE... -
Page 7: Seat Post Installation
5. Seat Post Installation 1. Unscrew main bolt (A) as far as possible without fully removing it from the lock nut. 2. Install the saddle rails into the seatpost clamp (B). 3. Slide saddle clamp (B) onto rocker (C). 4. Tighten the bolt up at 12Nm. See p.23 for saddle adjustment. -
Page 8: Seat Post Installation
6. Seat Post Installation The Di2 battery is hidden in the seatpost; use the Di2 battery holder (3.3) to fi x the battery correctly. Apply a slight amount of grease on both parts. CARBON FIBER ASSEMBLY PASTE GREASE GREASE... -
Page 9: Frame Inspection
7. Frame Inspection BEFORE ASSEMBLING YOUR NEW E-117 TRI DISC, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING: 1. Brakes hoses, gears cables and housing set 2: Frameset parts checklist (see p.5) 3: All the necessary bolts (refer to Frameset Parts, p.5) WHEN ASSEMBLING YOUR NEW E-117 TRI DISC, MAKE SURE YOU FOLLOW THIS PROCEDURE: 4: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.) 5: For reference, check serial number and write it on p.2... -
Page 10: Rear Derailleur Hanger Adjustment
8. Rear Derailleur Hanger Adjustment 1.3.3 1.3.3 1.3.1 1.3.2 1.3.2 1. Select the correct rear derailleur hanger depending on the type of derailleur that you have. - Direct mount (1.4) - Regular mount (1.3.1) 2. Make sure to align the rear derailleur hanger using a Derailleur Hanger Alignment Gauge like Park Tool Item #DAG-2,2. -
Page 11: Front Derailleur Hanger Adjustment
9. Front Derailleur Hanger Adjustment The front derailleur hanger can be adjusted according to the front derailleur angle in order to get an equal curve between the derailleur and the big chain ring. Once at the right angle, use blue 242 Loctite and screw in at 4Nm. -
Page 12: Headset Installation
10. Headset Installation Install the 3D headset (4) according to the pressfi t assembly guide. You can choose from 3 diff erent heights: 25mm, 15mm, or 0mm. GREASE GREASE GREASE... - Page 13 10. Headset Installation setup setup 25mm Compressor 15mm Top cap STEP First, you must assess which setup suits your needs: Micro spacers 25mm, 15mm or 0mm. setup Compression ring Bearing STEP Inspect the bike’s head tube for any sharp edges and 3D bearing holder apply a small amount of grease.
- Page 14 10. Headset Installation IMPORTANT : Use the Press Fit 3D system tool 1 1/2” with the Bearing Cup Press (ParkTool HHP-2) to avoid any damage on the bike frame. Compressor Top cap Micro spacers Compression ring Bearing 3D bearing holder Plastic sleeve (no need for 0mm setup) Top cap for 0mm setup Press Fit 3D system tool 1 1/2”...
-
Page 15: Cable Housing Installation For Mechanical Drive Train
11. Cable Housing Installation for mechanical drive train IMPORTANT: Install cable housing before installing the bottom bracket, crank, and fork. Front Rear derailleur derailleur Make sure to use the foam liner on both brake hose and derailleur housing to prevent any rattling noise Handlebar Section Rear Use standard housing and metal cap according to... -
Page 16: Cable Housing Installation For Electrical Drive Train
12. Cable Housing Installation for electrical drive train IMPORTANT: Install cable housing before installing the 1.11 1.10 bottom bracket, crank, and fork. Di2 cable Wireless Make sure to use the brake hose foam liner to prevent any rattling noise Rear Rear brake brake... -
Page 17: Cable Housing Installation
13. Cable Housing Installation Bottom Bracket Section 1. Measure approximately 660mm length (for a medium-sized frame) of one unit of LEX 4mm gear housing (mechanical) for the front derailleur. 2. Install plastic caps at each tip of the gears’ housings. 3. - Page 18 13. Cable Housing Installation 5. Pass the cable housings inside the downtube until they come out the top tube. 6. Be sure that the guide’s pin is inside the frame’s hole. 7. With a hook take the housings out of the frame by the top tube’s triangular hole.
-
Page 19: Rear Derailleur Grommet
14. Rear derailleur grommet 1.14 1.16 1.15 Mechanical Wireless IMPORTANT: For the Di2 cable section that runs through the drive side chainstay, use the preinstalled tube guide that is supplied with the frame. Use the proper cable grommet to fix the rear derailler cable correctly depending if you use mechanical drive-train (1.14) or electronic shifting (1.15/1.16). -
Page 20: Electronic Drive-Train Installation
15. Electronic Drive-train Installation The Di2 cable routing can be achieved easily using this simple trick: use a gear cable and a metal cable end to fi x the Di2 cable. For more information on Shimano Di2 electronic system installation, go to: si.shimano.com. -
Page 21: Saddle Adjustment
16. Saddle Adjustment 12Nm For horiziontal adjustement: 1. Loosen 5mm bolts. 2. Unscrew main bolt. 3. Install saddle rails into the rocker in the middle position. 4. Find desired setback. 5. Tighten the 5mm bolt up at 6Nm. 6. Adjust seat horizontally. 7. -
Page 22: Troubleshooting / Tips
Because some parts have a tight tolerance, it might be necessary to put a slight amount of grease under the top cap. 2. Saddle rails: If your saddle rails are not round and made of metal, please refer to Ritchey’s part numbers. These parts are not sold by Argon 18 but available on Ritchey’s website (ritcheylogic.com). -
Page 23: Min/Max Seat Post Insertion
18. Min/Max Seat Post Insertion NOTE: THE ABOVE IMAGE IS FOR VISUAL REFERENCE OF SEATPOST INSERTION ONLY Refer to the supplied tables for details on Saddle Height and SeatPost insertion limits. The correct frame size must be determined according to the saddle height limits. A.