Subscribe to Our Youtube Channel
Related Manuals for Concept Pro AIR8012-IP3M-Z
Summary of Contents for Concept Pro AIR8012-IP3M-Z
- Page 1 TROUBLESHOOTING AIR8012-IP3M-Z AIR8012-IP3M-Z Weatherproof Colour/Mono IP Motorised Zoom Camera USER MANUAL USER MANUAL...
- Page 2 CAUTION Installation should be made by a qualified service person and should adhere to all local codes. In order to prevent electric shock and avoid damage to waterproof seals, do not loosen any screws on the camera body. Adjust the sunshield to avoid exposing the lens to direct sunlight. Do not touch the front glass.
- Page 3 The Concept Pro AIR8012-IP3M-Z is a weatherproof IR camera, suitable for monitoring areas in hostile conditions and in low light. Fixing Bolt for Sunvisor Alarm Cable Audio Input Sunvisor Audio Output Mounting Bracket Service Video Output/SD Card Power Connector Network RJ45 Connector...
-
Page 4: Installation
INSTALLATION Important: Ensure all precautions are observed during installation. It is recommended the camera is tested during the most demanding environmental conditions such as low light or bright sunlight to ensure continuity of effective CCTV monitoring. You may find the use of an ND filter helpful. Remove the camera unit carefully from the box,and keep the accessories in a safe place. - Page 5 POSITIONING Point the Camera towardsthe area to be monitored.
- Page 6 Alarm Cable CONNECTION Audio Input Audio Output Power Connector Network Cable (RJ45) SWITCH PC/Laptop MODEM Check the power supply is the correct level and connect your power supply into the power port on the camera. Connect the RJ45 connector to your network switch. If you are using a PoE (Power over Ethernet) Switch, please remove the power supply as this is not required.
- Page 7 Use the steps below to find the camera’s IP address and connect to the camera over the local area network (LAN) using Concept Pro Lite, UPnP on Windows®7 or Bonjour in Mac OS® 1. Finding the camera IP using BNC Test Cable When the BNC test cable is connected to the camera, the IP address is shown on the test monitor.
- Page 8 3. Finding the camera’s IP address using Bonjour® in Mac OS® NOTE: To use this method, the camera computer must be on the same network. Bonjour® is enabled by default, and can be enabled/disabled using Concept Pro Lite (check the Concept Pro Lite manual for details) 1.
-
Page 9: Specification
SPECIFICATION AIR8012-IP3M-Z CAMERA 1/2.8” Progressive Scan CMOS Image Sensor Color 0.01Lux; IR ON 0 Lux Min. illumination ICR,Auto/Color/B&W Day & Night 1/5 - 1/20000s Shutter Speed Auto Iris True WDR>120dB Wide Dynamic Range 2D/3D Digital Noise Reduction 12X Module Optical Zoom Digital Zoom 3.8s... - Page 10 NETWORK Network Protocols: IPv4/IPv6, RTSP/RTP/RTCP, TCP/UDP, HTTPS, DHCP, DNS, DDNS, PPPoE, SMTP Motion Detection, Network disconnect, Disk alarm, I/O Alarm Alarm Trigger RTSP Video Standard RFC2326, Support QuickTime / VLC Player. User security authentication, Reset, Hardware WatchDog Security Web Language English, Chinese, Polish, Italian, Portuguese, Spanish Onvif, CGI System Compatibility...
- Page 11 DIMENSIONS 87mm 334mm...
-
Page 12: Troubleshooting
TROUBLESHOOTING Can’t find the camera IP address using Concept Pro Lite or other software: • Make sure Ethernet and/or DC power cables are correctly connected to the camera. • Make sure the PoE switch or DC power source meets the camera’s power requirements (class 3 PoE / 450mA / 5.4W /12V). - Page 13 The AIR8012-IP3M-Z is ideal for Number Plate Capture installations. Simply follow the instructions below to tweak the settings and the Number Plate Capture camera will be ready to 1. Please connect the Concept Pro IP camera to a POE switch and PC. Navigate to the IP cameras web interface.
- Page 14 3. To alter the Sensor Setting, select Debug mode. 4. Select Exposure Tab and apply these settings: • Mode: Manual • Fix Shutter: 1/10,000* • Max gain: 50* • Iris: F1.6* *This setting may need adjusting depending on the environment, please test and adjust for optimal performance.
- Page 15 5. Select DayNight Tab and apply these settings: • D/N Setting: Night mode • Tick IR LED • Select Fixed from drop down list • Strength @ 50%* *This setting may need adjusting depending on the environment, please test and adjust for optimal performance Enhanced Image: •...
Need help?
Do you have a question about the AIR8012-IP3M-Z and is the answer not in the manual?
Questions and answers