Advertisement
SKU # 1001093976
Model # ZE00802A
USE AND CARE GUIDE
NON-SUBMERSIBLE WATER TRANSFER PUMP
Questions, problems, missing parts? Before returning to the store call
Everbilt Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-844-241-5521
HOMEDEPOT.COM
Rev. 05/20/17
THANK YOU
We appreciate the trust and confidence you have placed in Everbilt through the purchase of this non-submersible sump pump. We strive to
continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Everbilt!
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Everbilt ZE00802A
Summary of Contents for Everbilt ZE00802A
- Page 1 THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this non-submersible sump pump. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home...
-
Page 2: Table Of Contents
Table of Contents Table of Contents ............2 Installation ..............5 Performance ..............2 Care and Cleaning ............7 Safety Information ............2 Troubleshooting ............8 Warranty ................. 3 Pre-Installation .............. 4 Performance GPH of Water @ Total Feet Of Lift Max. -
Page 3: Warranty
Safety Information (continued) CAUTION: Know the pump and its applications, IMPORTANT: Ensure the electrical power source is limitations, and potential hazards. adequate for the requirements of the pump. CAUTION: Periodically inspect the pump and system IMPORTANT: Before using the pump, check the hose components to ensure the pump suction screen is free of for holes or excess wear, which could cause leaks, and mud, sand, and debris. -
Page 4: Pre-Installation
Pre-Installation APPLICATION This pump is designed for portable applications. It can drain or remove water from the following: flooded areas, pool covers, clogged sinks, waterbeds, water basins, boats, stock tanks, etc. It can also be used to fill tanks or water beds. ... -
Page 5: Installation
Installation Attaching the suction hose to Priming water strainer Attach the clear suction hose (C) to the suction strainer (B) by Add water (approximately 1-2 Tbsp.) into the inlet to wet the pushing the male threaded end into the rubber coupler on the impeller of the pump (A). - Page 6 Installation (continued) Attaching the pump to a sturdy Operating base To operate, plug the pump (A) into a GFCI outlet. Attach the pump (A) to a sturdy base (table, board, etc.) to prevent it from tipping over. Make sure the hoses are as straight as This pump can be very loud when plugged in.
-
Page 7: Care And Cleaning
Care and Cleaning Do Not When the power is disconnected, inspect the pump suction Do not disassemble the motor housing. This motor has NO screen and remove all debris, then plug the pump back into repairable internal parts, and disassembly may cause the grounded (GFCI) outlet. -
Page 8: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action Motor runs but no water Be sure pump is actually running, not See section below called “Motor hums-pump not running”. is discharged just humming Discharge hose or pipe is blocked or Check hose/pipe for blockages. Check manual for maximum too restrictive lengths of pipe/hose that pump can handle. - Page 9 Repair as needed The impeller wears out Sand, dirt or other grit in the water is All Everbilt utility pumps are designed to pump clear water. If there quickly accelerating wear is dirt or grit in the water, the internal parts of the pump will wear at an accelerated rate.
- Page 10 Questions, problems, missing parts? Before returning to the store call Everbilt Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-844-241-5521 HOMEDEPOT.COM...
Need help?
Do you have a question about the ZE00802A and is the answer not in the manual?
Questions and answers