Advertisement
Quick Links
SKU # 1001093988
Model # ZE00804
USE AND CARE GUIDE
Non-Submersible 12V Utility Pump
Questions, problems, missing parts? Before returning to the store call
Everbilt Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-844-241-5521
HOMEDEPOT.COM
Rev. 05/20/17
THANK YOU
We appreciate the trust and confidence you have placed in Everbilt through the purchase of this non-submersible 12V utility pump. We strive to
continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Everbilt!
Advertisement
Related Manuals for Everbilt ZE00804
Summary of Contents for Everbilt ZE00804
- Page 1 THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this non-submersible 12V utility pump. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home...
-
Page 2: Table Of Contents
Table of Contents Table of Contents ................2 Installation ..................5 Performance ..................2 Operation ................... 6 Safety Information ................2 Maintenance ..................7 Warranty..................... 3 Troubleshooting ................8 Pre-Installation .................. 4 Performance GPH of Water @ Total Feet Of Lift Max. -
Page 3: Warranty
Safety Information (continued) CAUTION: Know the pump and its applications, IMPORTANT: Before using the pump, check the hose limitations, and potential hazards. for holes or excess wear, which could cause leaks, and ensure the hose is not kinked or making sharp angles. A straight hose allows the pump to move the greatest amount of water quickly, and also check that all hose CAUTION: Periodically inspect the pump and system... -
Page 4: Pre-Installation
Pre-Installation APPLICATION This non-corrosive pump, with flow direction, is designed to pump water only. Never operate the pump for more than two hours at a time. Never run the pump dry! This unit is not designed for applications involving salt water or brine! Use with salt water or brine will void the warranty. ... -
Page 5: Installation
Installation Attaching the suction hose to Priming water strainer Attach the clear suction hose (C) to the suction strainer (B) by Add water (approximately 1-2 Tbsp.) into the inlet to wet the pushing the male threaded end into the rubber coupler on the impeller of the pump (A). -
Page 6: Operation
Installation (continued) Attaching the pump to a sturdy base Attach the pump (A) to a sturdy base (table, board, etc.) to prevent it from tipping over. Make sure the hoses are as straight as possible. WARNING: This pump CANNOT be submersed in water, and the motor CANNOT get wet at all. -
Page 7: Maintenance
Maintenance When you have finished pumping, disconnect the wires from the power source to be sure the unit is turned off. NOTE: Use the supplied suction strainer. Keep the pump inlet clear. Impeller Replacement Remove the impeller cover screws (4). ... -
Page 8: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action Motor runs but no water Be sure pump is actually running, not See section below called “Motor hums-pump not running” is discharged just humming Discharge hose or pipe is blocked or Check hose/pipe for blockages. Check manual for maximum too restrictive lengths of pipe/hose that pump can handle. - Page 9 Corrective Action The impeller wears out Sand, dirt or other grit in the water is All Everbilt utility pumps are designed to pump clear water. If there quickly accelerating wear is dirt or grit in the water, the internal parts of the pump will wear at an accelerated rate.
- Page 10 Questions, problems, missing parts? Before returning to the store call Everbilt Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-844-241-5521 HOMEDEPOT.COM...