pottery barn kids CATALINA STORAGE TOWER Quick Start Manual
pottery barn kids CATALINA STORAGE TOWER Quick Start Manual

pottery barn kids CATALINA STORAGE TOWER Quick Start Manual

Advertisement

PRE-ASSEMBLY:

Please read all instructions before beginning assembly.
Assembly by two adults is recommended for your safety and ease.
Remove all parts and hardware from the box. Place them on a carpeted or scratch-free work surface, as this will avoid
damaging any parts during assembly. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any contents until assembly is complete.
Use the parts and hardware lists to identify and separate each of the pieces included.
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts to
misalign during assembly.
The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood.

PART INCLUDED

(A) Top Panel
(B) Left Side Panel
(C) Right Side Panel
(D) Front Frame
(E) Back Frame
(F) Shelves
(G) Base
(H) Back Panel
Date: 9-Aug-2012
Pottery Barn Kids
CATALINA STORAGE TOWER
- 1 pc
- 1 pc
- 1 pc
- 1 pc
- 1 pc
- 4 pcs
- 1 pc
- 1 pc
Thank you for your purchase
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
A
B
E
D
F
F
F
F
G
H
C
Page 1 of 5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CATALINA STORAGE TOWER and is the answer not in the manual?

Questions and answers

Summary of Contents for pottery barn kids CATALINA STORAGE TOWER

  • Page 1 Pottery Barn Kids CATALINA STORAGE TOWER PRE-ASSEMBLY: Please read all instructions before beginning assembly.  Assembly by two adults is recommended for your safety and ease.  Remove all parts and hardware from the box. Place them on a carpeted or scratch-free work surface, as this will avoid ...
  • Page 2 (S) Phillips head screw driver (not included) - 1 pc Assembly Instructions For The Catalina Storage Tower Insert 8 Dowels 8 x 30mm (R) to the Left Side Panel (B). Assemble the Left Side Panel (B) with 4 Shelves (F) using JCBC Bolts M6 x 32mm (I), Lock Washer (N), and Flat Washer (O) with the Allen key (M).
  • Page 3 Attach the Front Frame (D) and the Back Frame (E) to the Left Side Panel (B). At the same time, attach the Right Side Panel (C) to the Front Frame (D), Back Frame (E), and 4 Shelves as shown in the picture below. Using the Allen Key (M), attach the Front Frame (D) and Back Frame (E) with the following hardware: Half Moon Washer (L), JCBC Bolts M6 x 50mm (J), and Lock Washer (N).
  • Page 4 Assemble the Base (G) using JCBC Bolt M6 x 70mm (K), Lock Washer (N), Flat washer (O), and Dowel 8 x 30mm (R) with the Allen key (M), as shown in the picture below. (K) (N) (O) (M) (R) Position the Back Panel (H) on the Back of the Storage tower as shown in the picture below. Insert 26 of the 6x19mm Screws (P) into the pre-drilled holes on the Back Panel (H).
  • Page 5 Slowly turn the Storage tower to the upright position with a helper. Adjust levelers under legs to balance the tower if necessary. CARE INSTRUCTIONS: Dust often using a clean, soft, dry, lint-free cloth.  Blot spills immediately, and wipe with a clean, damp cloth. ...

Table of Contents