Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de BLAUBERG Ventilatoren GmbH is happy to off er your attention the Tower- The transported air must not contain any dust or other solid impurities, V(H) / Tower-V(H) EC centrifugal roof fan.
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de DESIGN The fan casing is made of steel with a special weatherproof polymer life. The built-in thermal switches are used for overheating protection. The coating. The air discharge is horizontal in the Tower-H / Tower-H EC models thermal switches are equipped with terminals leaded outside for connection and vertical in the Tower-V / Tower-V EC models.
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de DELIVERY SET ATTENTION Make sure the unit has no visible transport damages while fan - 1 item; accepting the goods. Check the ordered and the delivered operation manual - 1 item; goods for compliance.
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de MOUNTING AND OPERATION GUIDELINES WARNING Before starting mounting: read carefully the operation manual of the unit; check the unit for possible transport damages. Follow the safety regulations during the unit start-up and operation. Fans are designed for mounting on a roof directly above an air duct or a ventilation shaft.
Page 8
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de 10) Install the protecting housing and fi x it with 8 bolts. 6) Route the electric cable through the electric lead-in located in the base casing. Install the base with the motor on the pan and fi x it using bolts. Route the electric cable through the electric lead-in located in the terminal box casing and connect it to the terminal block according to the wiring diagram.
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de 5) Remove the protecting housing. 6) Lead the electric cable to the fan mounting place then route it through 9) Fix the cover using 4 nuts. the electric lead-in located in the casing of the fan pan. Install the pan of the fan over the ventilation shaft and fi x it using dowels.
Page 10
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de Depending on the model the fan is rated for connection to 230 V / 50-60 External wiring diagram and universal connection of fans with EC motors Hz single-phase AC or to 400 V / 50-60 Hz three-phase AC power mains, refer into a single group is shown in Fig.
Page 11
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de ~400 V 50 Hz Terminal Contact Purpose/function block power mains 50-60 Hz, phase power mains 50-60 Hz, zero wire protective ground warning relay, normally closed contact warning relay, common + 10 V voltage output +10 V (no more than 1.1 mA) control input 0-10 V / PWM 0-10 V/PWM...
Page 12
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de PC with the interface Pressure sensor Warning relay converter (RS 486) Power mains 50-60 Hz Power mains 50-60 Hz Power mains 50-60 Hz Fig. 14. ~400 V ~230 V 50 Hz 50 Hz “On”...
Tower-V / Tower-H / Tower-V EC / Tower-H EC www.blaubergventilatoren.de TECHNICAL MAINTENANCE WARNING Cut power supply to the fan off by turning the automatic electric switch QF to OFF position prior to any maintenance operations. Take steps to prevent activation of the automatic switch prior to fi nishing maintenance. Disconnect the fan from power mains prior to any operations related to 2.
Company: Expert's Full Name Date Signature WARRANTY CARD Tower-V Tower-V EC Tower-H Tower-H EC SELLER PURCHASE DATE REPRESENTATIVE IN EU BLAUBERG Ventilatoren GmbH Aidenbachstr. 52a, D-81379 Munich, Germany...
Need help?
Do you have a question about the Tower-V Series and is the answer not in the manual?
Questions and answers