Snd Hold (Sound Hold); S-Bend; Touch Wh (Touch Wah)/ Tw Bass (Touch Wah Bass); Tremolo - Boss GT-1000CORE Parameter Manual

Effect

SND HOLD (SOUND HOLD)

You can have sound played on the guitar be held continuously. This
effect allows you to perform the melody in the upper registers while
holding a note in the lower registers.
* This function will not work properly when two or more notes are
played simultaneously.
Parameter Value Explanation
Switches the hold sound on and off. Normally, this is
controlled with the CTL pedals.
5 It is assumed that this parameter will be assigned to
TRIGGER OFF, ON
the footswitch.
5 Patches are written with the HOLD parameter set
to Off.
RISE TIME
0–100 Adjusts how rapidly the Sound Hold sound is produced.
E.LEVEL
0–120 Adjusts the volume of the hold sound.

S-BEND

Applies intense bending.
Parameter Value
TRIGGER
OFF, ON
-3oct, -2oct, -1oct,
PITCH +1oct, +2oct,
+3oct, +4oct
RISE TIME
0–100
FALL TIME 0–100
TOUCH WH (TOUCH WAH)/
TW BASS (TOUCH WAH BASS)
You can produce a wah effect with the filter changing in response to
the guitar/bass level.
Parameter Value Explanation
Selects the wah mode.
LPF Low pass filter. Passes only the low-frequency region.
High pass filter. Passes only the high-frequency
FILTER
HPF
region.
Band pass filter. Passes only the specified frequency
BPF
region.
Selects the direction in which the filter will change in response to
the input.
POLARITY
DOWN The frequency of the filter will fall.
UP The frequency of the filter will rise.
Specifies the sensitivity with which the filter moves in
the direction specified by the POLARITY setting.
SENS 0–100
Higher values will result in a stronger response. With
a setting of 0, the strength of picking will have no
effect.
SENS
0–100 Adjusts the center frequency of the Wah effect.
Adjusts the way in which the wah effect applies to
the area around the center frequency.
FREQ
0–100
Higher values will produce a stronger tone which
emphasizes the wah effect more. With a value of 50 a
standard wah sound will be produced.
DECAY
0–100 Adjusts the rate at which the filter is moved.
24
Explanation
The effect is applied when you switch this from
OFF to ON.
When the patch is written, this parameter is
stored in the OFF state.
Adjusts the amount of pitch shift in octave
steps.
This parameter adjusts the amount of time
it is to take for the effect to transition to the
maximum.
This parameter adjusts the amount of time it is
to take for the effect to transition to the original.
Parameter Value Explanation
E.LEVEL
0–100 Adjusts the volume of the effect sound.
DIR MIX
0–100 Adjusts the volume of the direct sound.

TREMOLO

Tremolo is an effect that creates a cyclic change in volume.
Parameter Value
0–100,
RATE
BPM ΠР`
DEPTH
0–100
WAVEFORM 0–100
E.LEVEL 0–100
TRIGGER OFF, ON
RISE TIME
0–100
DIR MIX 0–100
BPM 40–250
Explanation
Adjusts the frequency (speed) of the change.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch. This makes it easier to achieve
effect sound settings that match the
tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it is
then synchronized to a period either 1/2
or 1/4 of that time.
Adjusts the depth of the effect.
Adjusts changes in volume level. A higher
value will steepen wave's shape.
Adjusts the volume.
Turns the tremolo on/off.
Specifies the time from when trigger turns
on until the specified tremolo effect is
obtained.
Adjusts the volume of the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that occur
each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI devices
tempo, making it impossible to set the
MASTER BPM. To enable setting of the
MASTER BPM, set "SYNC CLOCK" (p. 47) to
"INTERNAL. "