Pedal Fx - Boss GT-1000CORE Parameter Manual

Effect
Parameter Value
DUCK PRE *1 0–100
DUCK PST *1 0–100
D.LEVEL 0–100
*1 This is not shown if TYPE is set to TERA ECHO.
SHIMMER
Parameter Value Explanation
1:PITCH
-24–+24 Adjusts the amount of pitch shift.
2:PITCH
1:LEVEL
0–100 Adjusts the volume of the pitch shifter.
2:LEVEL
DUAL
Parameter Value
1:TYPE
HALL, PLATE,
ROOM
2:TYPE
1:TIME
0.1–10.0s
2:TIME
1:TONE
-50–+50
2:TONE
1:LEVEL
0–100
2:LEVEL
1:DENSTY
1–10
2:DENSTY
1:PRE-DL
0ms–200ms
2:PRE-DL
1:LO CUT
FLAT,
20.0Hz–20.0kHz
2:LO CUT
1:HI CUT
20.0Hz–20.0kHz,
FLAT
2:HI CUT
TERA ECHO
Parameter Value Explanation
Selects the mode of the effect sound.
MONO The L and R channels will both output the same
sound.
MODE
STEREO 1 The R channel outputs the direct sound, and the
L channel outputs the effect sound.
STEREO2 The effect is applied separately to the L and R
channels.
SPREAD 0–100 Adjusts the length of the effect sound.
FEEDBACK 0–100 Adjusts the decay of the effect sound.
E.LEVEL 0–100 Adjusts the volume of the effect sound.
TONE -50–+50 Adjusts the tone.
D.LEVEL 0–100 Adjusts the volume of the direct sound.
26
Explanation
When the input sound is loud, this
automatically reduces the volume that is
being input to the reverb and delay. As this
setting approaches 100, the input volume
reduction is applied more deeply.
When the input sound is loud, this
automatically reduces the volume that is
being output from the reverb and delay.
As this setting approaches 100, the output
volume reduction is applied more deeply.
Adjusts the volume of the direct sound.
Explanation
This selects the reverb type.
Adjusts the length (time) of
reverberation.
Adjusts the tonal character of the reverb.
Adjusts the volume of the reverb sound.
Adjusts the density of the reverb sound.
Adjusts the time until the reverb sound
appears.
This sets the frequency at which the low
cut filter begins to take effect. When
FLAT is selected, the low cut filter will
have no effect.
This sets the frequency at which the
high cut filter begins to take effect.
When FLAT is selected, the high cut filter
will have no effect.
Parameter Value Explanation
The effect sound is held when you turn this on.
TRIGGER OFF, ON

PEDAL FX

You can control the wah effect or get a pitch bend effect in real time
by adjusting the GT-1000CORE's expression pedal or the expression
pedal connected to the CTL 2, 3/EXP 1 jack or CTL 4, 5/EXP 2 jack.
Parameter Value Explanation
ON/OFF OFF, ON Turns this effect on/off.
This lets you use the pedal to get a pitch bend
effect.
PDL BEND
* Because of the need to analyze the pitch,
TYPE
You can control the wah effect in real time by
adjusting the GT-1000CORE's expression pedal or
WAH
the expression pedal connected to the CTL 2, 3/
EXP 1 jack or CTL 4, 5/EXP 2 jack.
PEDAL BEND
Parameter Value
PITCH MIN
-24–+24
PITCH MAX -24–+24
PDL POS
0–100
E.LEVEL 0–100
DIR MIX 0–100
5 Patches are written with the parameter set
to Off.
chords (two or more sounds played
simultaneously) cannot be played.
Explanation
Specifies the pitch when the pedal is
returned.
This sets the pitch at the point where the EXP
Pedal is all the way down.
Adjusts the pedal position for pedal bend.
This parameter is used after it's been
assigned to an expression pedal or similar
controller.
Adjusts the volume of the pitch bend sound.
Adjusts the volume of the direct sound.