REFERENCE GUIDE EL-NVR-8CH CONTENTS ABOUT THIS DOCUMENT ....................4 ELECTROMAGNETIC COMPATIBILITY (EMC) ..............4 Compliance ............................4 Features ............................5 Caution ..............................5 INSTALLING THE NVR IN THE STRUCTURED WIRING CAN ........... 6 HARD DRIVE - REMOVAL AND INSTALLATION INSTRUCTIONS ........7 Removing the Hard Drive ........................7 Installing the Hard Drive ........................8...
Page 3
REFERENCE GUIDE EL-NVR-8CH PTZ Setup ...........................42 PTZ Setup > General ........................42 PTZ Setup > NVR Cascade ......................43 Meta data Setup .........................44 Meta Data Setup > General ......................44 Other Setup ........................47 Other Setup > Smart Phone ......................47 Other Setup >...
REFERENCE GUIDE EL-NVR-8CH ABOUT THIS DOCUMENT This document includes instructions for basic operation of the EL-NVR-8CH Network Video Recorder. ELECTROMAGNETIC COMPATIBILITY (EMC) This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
• Up to 48 Mbps incoming network throughput • Full HD 4K HDMI and 1080p VGA output • Compatible with iOS and Android devices via the ELAN mobile app Caution • Do not drop or strike the equipment • Do not install the equipment near open flames or heat sources •...
REFERENCE GUIDE EL-NVR-8CH INSTALLING THE NVR IN THE STRUCTURED WIRING CAN 1. Align the bracket holes (x4) with the holes in the wiring can. 2. Insert the snap rivets (x4) through each bracket hole (x4) and then into the wiring can holes.
REFERENCE GUIDE EL-NVR-8CH HARD DRIVE - REMOVAL AND INSTALLATION INSTRUCTIONS Removing the Hard Drive 1. Remove screws (x4) located in top corners of upper casing, carefully lifting it upwards. Note: The connector cable is attached to the hard drive located in the upper casing.
REFERENCE GUIDE EL-NVR-8CH 3. Remove the screws (x4) from the brackets located on both sides of the hard drive. 4. Remove hard drive. Installing the Hard Drive Note: Only Western Digital Purple Surveillance Drives are supported, up to 8TB. 1. Insert the hard drive between the brackets, aligning the hard drive screw holes (x4) with the holes in the brackets.
Page 9
REFERENCE GUIDE EL-NVR-8CH 3. Reinsert SATA and power cable into hard drive. 4. Slide cover over NVR. 5. Insert and tighten the screws (x4). (x4) Note: The new hard drive must be formatted using the NVR before it can be recorded to.
If you are confi guring with an ELAN controller, it is not recommended to make changes via the NVR Web GUI. The ELAN software controls the vast majority of these functions. The software confi guration information in this document can be used to extend device control parameters for use within an ELAN controller environment, or for operating this hardware independent of an ELAN controller.
REFERENCE GUIDE EL-NVR-8CH LOCATING NVR IP ADDRESS ELAN NVRs are set to DHCP out of the box. Connect your ELAN NVR to the network, using your preferred network scanning app, and scan for the NVR. The NVR’s name is EL-NVR-8CH.
REFERENCE GUIDE EL-NVR-8CH LANGUAGE SETUP/SWITCH USERS When setting the NVR up for the first time, ‘click’ on the gear icon in the upper-right corner of the user interface. A dialog box with two options will appear, switch user and language.
REFERENCE GUIDE EL-NVR-8CH NVR SYSTEM NVR System > General To enter NVR settings, ‘click’ SYSTEM in the left pane where you are allowed to adjust the NVR’s confi guration. Device ID: Assign an ID for the NVR to be controlled by the remote controller.
To enter NVR settings, ‘click’ SYSTEM in the left pane where you are allowed to adjust the NVR’s confi guration. Note: Do not modify these setting when the NVR is connected to an ELAN controller. Date/Time: Set the date/time of the NVR.
REFERENCE GUIDE EL-NVR-8CH NVR SYSTEM (CONT.) NVR System > User To enter NVR settings, ‘click’ SYSTEM in the left pane. This allows you to adjust the NVR’s confi guration. The NVR supports up to 15 sets of individual user settings (including default user administrator, operator, and guest), allowing you to assign different access privileges.
REFERENCE GUIDE EL-NVR-8CH NVR SYSTEM (CONT.) NVR System > Storage ‘Clicking’ STORAGE in the left pane allows you to adjust HDD MGT., S.M.A.R.T., and USB MGT. HDD Management: In HDD MGT., you are allowed to format, defrag, check malfunctioned blocks, or run an overall system check on any of the devices.
Page 18
REFERENCE GUIDE EL-NVR-8CH NVR SYSTEM (CONT.) NVR System > Storage (Continued) S.M.A.R.T: The S.M.A.R.T. status of your hard drive is displayed in S.M.A.R.T., where you can run analysis (either short or extended) on the HDD. Choose between Short or Extended analysis and ‘click’...
REFERENCE GUIDE EL-NVR-8CH NVR SYSTEM (CONT.) NVR System > Event System: The search fi eld in this page allows you to search for specifi c event reports at different time and of different content. ‘Press’ Download to export the event report.
Page 20
Firmware Update: Choose a fi rmware fi le and ‘click’ Update to proceed fi rmware update. Note: Firmware can be also be updated via ELAN Confi gurator. Export Settings: ‘Click’ Export to copy system settings to a USB fl ash drive.
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP Network Setup > General Enter the required information in the fi elds: IP Mode: Select the connection type of the NVR from Static, DHCP, and PPPoE. IP Address: Enter the IP address you want to use, and ‘press’...
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > General (Continued) FTP Port: Specify the desired FTP port. MAC: This is the MAC address of your NVR. PPPoE Account: If you choose to connect through PPPoE, enter the account name here.
Page 23
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > E-Mail When an alarm is triggered, the NVR can automatically send e-mail notifi cations to the recipients you designated. The setting options are described below: Send E-Mail: ‘Check’ the box to enable sending e-mail notifi cations when an alarm is triggered.
Page 24
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > E-Mail (Continued) E-Mail Host: Enter the mail server address of your e-mail server. Port: Enter the port of your e-mail server. JPEG File: ‘Check’ to also attach JPEG photos when an alarm is triggered.
Page 25
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > E-Mail (Continued) System Events: ‘Click’ to open the dialog below. HDD S.M.A.R.T. abnormal ‘Check’ to send E-Mail when an S.M.A.R.T. error is detected. HDD track error: ‘Check’ to send E-Mail when an HDD error is detected.
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > FTP FTP Server: Enter the IP address of the FTP server. Port: Enter the port of the FTP server. Account: Enter the account name of the FTP server. Password: Enter the password of the FTP server Prefi...
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONTINUED) Network Setup > DDNS Choose the DDNS server you want to use. Hostname: Enter the hostname of the DDNS server. User: Enter the username to log in to the DDNS server. Password: Enter the password to log in to the DDNS server.
REFERENCE GUIDE EL-NVR-8CH NETWORK SETUP (CONT.) Network Setup > Other The NVR also supports other protocols such as UPnP and SDDP, and related confi gurations can be modifi ed in the OTHER tab. The setting options are described below. Choose the DDNS server you want to use.
CAMERA SETUP Camera Setup > General If you are installing an ELAN Cameras and/or ELAN NVR with an ELAN Controller, please refer to the “ELAN Surveillance” Integration Note for setup and software confi guration. ELAN Integration Notes are served through the ELAN tools and on elanhomesystems.com/dealer-resources.”...
Page 30
REFERENCE GUIDE EL-NVR-8CH CAMERA SETUP (CONT.) Camera Setup > General (Continued) User: Enter the username required for camera authorization. Password: Enter the password required for camera authorization. Stream Type: Choose whether to stream only the primary video or dual (primary & secondary) videos.
REFERENCE GUIDE EL-NVR-8CH CAMERA SETUP (CONT.) Camera Setup > Video On this page, you can adjust several camera parameters including Contrast, Brightness, Saturation, and Sharpness. ‘Click’ Default to restore the NVR to its factory settings. ‘Click’ Refresh to update the preview image.
REFERENCE GUIDE EL-NVR-8CH RECORD SETUP Record Setup > General ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ RECORD ( ) in the left pane to enter the RECORD SETUP page. The setting options are described below. Record Mode: Switch on/off scheduled recording.
REFERENCE GUIDE EL-NVR-8CH RECORD SETUP (CONT.) Record Setup > Schedule To modify the recording schedule, switch the recording type from Always (continuous recording), Alarm (record only when an alarm is triggered), or No Record (disable recording), and highlight the desired date and time accordingly.
REFERENCE GUIDE EL-NVR-8CH ALARM SETUP ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ ALARM ( ) in the left pane to enter the ALARM SETUP page. The setting options are described below. Alarm Setup > General Alarm Input Type: Set the alarm sensor to Normally Open (NO), Normally Closed (NC), or IP Camera.
REFERENCE GUIDE EL-NVR-8CH ALARM SETUP (CONT.) ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ ALARM ( ) in the left pane to enter the ALARM SETUP page. The setting options are described below. Alarm Setup > Motion Area Selecting Motion Detection Areas: •...
REFERENCE GUIDE EL-NVR-8CH ALARM SETUP (CONT.) ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ ALARM ( ) in the left pane to enter the ALARM SETUP page. The setting options are described below. Alarm Setup > Output ALARM LED Enable: Turn On to activate the alarm LED.
Page 37
Turn On to activate e-mail sending. Trigger Conditions: See Channel Events and System Events above for more details. Alarm Send Interval: Set the frequency of sending alarm notifi cation e-mail. NOTIFICATION: Push notifi cations are sent from the ELAN Controller. www.elanhomesystems.com 10024106_REV-A_EL-NVR-8CH...
Page 38
REFERENCE GUIDE EL-NVR-8CH ALARM SETUP (CONT.) Alarm Setup (Cont.) > Output (Cont.) DO#1–N (Manual DO control) Manual DO control: Turn On to enable DO, the live video of which will show the corresponding alarm output number. Note: For other options, please refer to the descriptions in the beginning of this section.
REFERENCE GUIDE EL-NVR-8CH DISPLAY SETUP DISPLAY ( ) provides several adjustable NVR parameters such as resolution, default number of split views, and more other options. The details of these settings are described as follows: Display Setup > General Backlight Saving: Adjust the level of screen brightness reduction once the time specifi...
REFERENCE GUIDE EL-NVR-8CH DISPLAY SETUP (CONT.) Display Setup > Advanced In this page, you can adjust brightness, contrast, and saturation of the NVR output. Also, it is possible to change of intensity of the 2DNR and 3DNR noise reduction feature.
REFERENCE GUIDE EL-NVR-8CH DISPLAY SETUP (CONT.) Display Setup > Sequence You are allowed to view videos of multiple cameras in sequence. ‘Check’ the cameras you want to monitor and choose the number of split views in the drop-down menu in Sequence Mode.
REFERENCE GUIDE EL-NVR-8CH PTZ SETUP ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ PTZ ( ) in the left pane to enter the PTZ SETUP page. The setting options are described below. PTZ Setup > General Transfer Mode: Choose a PTZ communication protocol from HTTP, ONVIF, or Fish Eye. Otherwise use RS- 485.
PTZ Setup > NVR Cascade This tab allows you to cascade multiple NVRs or adjust relevant settings. For detailed instructions on how to use the NVR cascade function, contact ELAN technical support. The settings listed in this tab are described, as follows: Show/Hide: Reveal or hide the password.
Notes: • The Meta Data tab is pre-confi gured for IntelliVision enabled ELAN cameras. • The settings are pre-defi ned for ELAN Surveillance cameras with IntelliVision Analytics. Modifying these settings is not recommended.
Page 45
REFERENCE GUIDE EL-NVR-8CH META DATA SETUP (CONT.) Meta Data Setup > General (Cont.) Encoding Mode: Choose between ASCII and UTF-8. Baud Rate: Select an option suitable for your device. Data Size: Select an option suitable for your device. Parity: Select an option suitable for your device.
Page 46
REFERENCE GUIDE EL-NVR-8CH META DATA SETUP (CONT.) Meta Data Setup > General (Cont.) Meta Data Setup > Event This tab displays a history of received metadata. You are allowed to search for events based on time, channel, or content. www.elanhomesystems.com...
REFERENCE GUIDE EL-NVR-8CH OTHER SETUP ‘Click’ settings ( )to enter NVR SETTINGS, and ‘press’ OTHER ( ) in the left pane to enter the OTHER SETUP page. The setting options are described below: Other Setup > Smart Phone Other Setup > IVS The NVR supports IVS-enabled cameras.
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP Once the network confi gurations are completed and cameras connected, you can remotely view live streams of cameras via an Internet browser, and access other functions, such as playing recorded video and backing up video fi les.
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP (CONT.) Stream Setup > Live The LIVE tab displays the streams of all connected cameras. With the control buttons and joystick you can control the movement of the selected camera if it has PTZ capabilities.
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP (CONT.) Stream Setup > Backup In BACKUP, you can back up recorded videos by choosing the Date/Time, Start Time/End Time, Channel, and File Format. Date/Time Select the month, day, and year of the fi le clip you would like to export.
Page 51
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP (CONT.) Stream Setup > Backup Start Time/End Time Select the time range you would like to export. Channel Select the camera channels you would like to export. File Format In the drop-down box, you are presented with 4 fi le format options.
Page 52
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP (CONT.) Stream Setup > Backup File Format Defi nitions: • SD H.264 Raw Data This option uses a standard definition proprietary fi le type which is locked and cannot be edited. This option will allow multiple channels to be displayed concurrently on playback but will require the backed up fi...
REFERENCE GUIDE EL-NVR-8CH STREAM SETUP (CONT.) Stream Setup > Saving Backup File Once you ‘press’ the Backup button, a fi le is generated which will appear on the top right side of the screen. ‘Click’ on the fi lename and your web browser will download the fi le to your computer.
REFERENCE GUIDE EL-NVR-8CH APPENDIX Hard Reset Perform the hard reset to restore NVR to the factory settings. 1. Navigate to System>Maintenance>Factory Reset through HDMI out to Monitor. 2. ‘Click’ Reset ( ) to restart the NVR. The device will restart and restore to the factory settings.
Page 55
× 1 (Up to 8TB external storage supported) Backup USB Flash Disk Up to 32 GB supported Network Backup Via HTTP / FTP / ELAN UI PC/Mac Audio Audio Input 8 CH ( network camera ), G.711 8K Audio Output RCA ×...