Golden Designs LSDT-02 Manual
  1. Manuals
  2. Brands
  3. Golden Designs Manuals
  4. Plumbing Product
  5. LSDT-02
  6. Manual

Golden Designs LSDT-02 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model: LSDT-02 & LSDT-03
FOR CARBON MODEL SAUNAS
HEMLOCK AND RED CEDAR MODELS
FOR INDOOR USE ONLY
LSDT-02: 120V/15AMP DEDICATED CIRCUIT REQUIRED
LSDT-03: 120V/20AMP DEDICATED CIRCUIT REQUIRED
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LSDT-02 and is the answer not in the manual?

Questions and answers

Related Manuals for Golden Designs LSDT-02

Summary of Contents for Golden Designs LSDT-02

  • Page 1 Model: LSDT-02 & LSDT-03 FOR CARBON MODEL SAUNAS HEMLOCK AND RED CEDAR MODELS FOR INDOOR USE ONLY LSDT-02: 120V/15AMP DEDICATED CIRCUIT REQUIRED LSDT-03: 120V/20AMP DEDICATED CIRCUIT REQUIRED...

  • Page 2: Table Of Contents

    Thank you for your purchase of the Infrared Sauna! Index ===================================== Page: Important Safety Guides................2 Introduction....................3 Health & Beauty Benefits................3 Highlights...................... 4 Assembly...................... 4 Operating Your Sauna.................. 12 Tips For Using Your Sauna................14 Safety Instructions..................15 Safeguards For Your Sauna.................

  • Page 3: Important Safety Guides

    READ IMPORTANT SAFETY GUIDES BEFORE USING! READ AND FOLLOW ALL INSTRUCTIONS A). Please follow all warning labels and markings on the sauna room before using. B). Do not install any receptacles on the interior or exterior walls of the sauna room.

  • Page 4: Introduction

    using the sauna. Excessive temperature has the potential for causing fetal damage during pregnancy. M). Never sleep inside the sauna. N). Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with a cloth and water. O).

  • Page 5: Highlights

    Highlights a. High quality craftsmanship b. Automatic thermostat for constant temperature c. Timer and buzzer: buzzer sounds 5 minutes before the end of the sauna session d. Digital sensor and thermometer e. Infrared carbon heat emitter panels Power supply: Main Power: main power to sauna room HT1, HT2, HT3, &...
  • Page 6 Sauna Room Assembly: 1. Structure of Infrared Sauna. See FIG-1 2. Make sure all parts are present before installing the unit. See packing list below. A. Front Panel B. Floor Panel C. Back Panel D. Left Side Panel E. Right Side Panel F.
  • Page 7 1. Power Supply 6. Left Side Panel 1000 x 400mm 300W 2. Color Lights 7. Rear Wall Panels 1000 x 400mm 300W 3. Temperature Sensor 1000 x 400mm 300W 4. Speakers 1000 x 400mm 200W 5. Control Panel 8. Right Side Panel 1000 x 400mm 300W 9.
  • Page 8 FIG-2.1 Cartons FIG-2.2 C/No. 4. Place the Floor Panel on a smooth/flat surface and make sure which side is the front and which side is the back. The front of the floor has no stain finish as the other three sides do. See FIG 3. FIG 3 Placing Floor Panel FIG 4 Assembling Back Panel...
  • Page 9 FIG 5 Assembling Right Side Panel FIG 6 Buckle 7. Latch the Right Side Panel with the Back Panel. The buckle has a guide tab that must be placed in the guide slot for alignment. When the Back Panel and the Side Panel are attached together on the floor panel, make sure all the buckles are latched.
  • Page 10 Bench Heating Board Floor Heater Floor Heater Wire FIG 8.1 Connect Floor Heater 10. Slide the Bench Heater Panel down (vertically) into the slot at an angle and pull it forward as seen in FIG 9. Connect the Bench Heater Panel cord with the cord coming from the Rear Wall Panel. Next, place the Bench on top of the Bench Heater Panel and slide it into place all the way back against the Rear Wall Panel.
  • Page 11 FIG 11 Assembling Front Panel FIG 12 Installing Roof Cover 12. Place cords/wires of Side Panel and Back Panel into the sauna room area to avoid damaging the cords/wires during the roof installation. Open the door, lift the Roof Panel up and over the sauna room, and gently lower it into place resting it on the wall panels.
  • Page 12 FIG 15 FIG 16 FIG 17 FIG 18...

  • Page 13: Operating Your Sauna

    14. Make sure all steps are completed correctly. Plug in the power cord to your wall outlet. Turn on the sauna at the control panel to confirm that the control panel is responding. If the control panel responds accordingly, then proceed in putting the Roof Cover onto the Roof Panel. Make sure to pull the power cord through the corresponding hole in the Roof Cover.
  • Page 14 Operating the Sauna NOTE: Before the sauna is turned on, remove plastic protective covering from the CONTROL PANELS. Please check and confirm that the connections to the POWER SUPPLY, HEAT EMITTERS, and TEMPERATURE SENSOR are connected properly. The power supply voltage and frequency must match the requested voltage and frequency of the sauna (120VAC 15AMP Dedicated Circuit or 120VAC 20AMP Dedicated Circuit).

  • Page 15: Tips For Using Your Sauna

    Reading lamps and/or roof lamps and/or color therapy lamps are operated by pressing the button located on the control panel. These lamps are offered on some models and are not available on all models. When you press the button once, the interior light will come ON. When you press the button twice, the interior light will turn OFF.

  • Page 16: Safety Instructions

    Tips for using Your Sauna 1) If you take a hot/warm shower or bath before using your sauna, you may perspire more and experience more comfort. 2) Drink water prior to, during, and after your sauna session to replenish body fluids. 3) To regulate the set temperature inside the sauna to your comfort level, use the movable roof ventilation or leave the door open slightly.

  • Page 17: Safeguards For Your Sauna

    9.) Persons using medications should consult a physician before using the sauna. Some medications may induce drowsiness while others may affect the heart rate, blood pressure, and/or blood circulation. 10) Exercise care before and after sauna use. 11) Never sleep inside the sauna. 12) Do not use any type of cleaning agents on the interior of the sauna.

  • Page 18: Troubleshooting Guide

    Troubleshooting Guide 1. No Heat Coming From Some Of The Heat Emitters Solution: Check to make sure all the heat emitter cords are properly connected, including the cord to the heat emitter underneath the bench (if applicable). Go to the roof, and also check that the heat emitter cords are properly connected to the cords on the roof and that those cords are properly plugged into the power supply.
  • Page 19 testing purposes, insert the “TEMP SENSOR” (you just connected) down the vent on the roof so that it is now inside the sauna. Then go to the control panel and press the power button. If the heat emitters now heat, then the temperature sensor was the cause of the problem. You may have to wait about five minutes to confirm if the heat emitters are generating heat.

  • Page 20: Warranty

    Limited Lifetime Warranty 5 Year Limited Warranty: Golden Designs, Inc. warranties the wood, structure, heating elements, and electronics against defects in material and workmanship for a period of 1 to 5 years from the original date of purchase. This sauna is for INDOOR use only. Placing your sauna outdoors will VOID this warranty.

  • Page 21: Warranty Card

    WARRANTY CARD Congratulations on your purchase of an Infrared Sauna from Golden Designs, Inc. Please take the time to complete the following Warranty Card and mail it back to: Golden Designs, Inc. 3550 Jurupa Street, Unit B Ontario, CA 91761 Please include a copy of your sales receipt showing date of purchase as this will serve as proof of purchase.

This manual is also suitable for:

Lsdt-03

Table of Contents