Summary of Contents for YOKOGAWA FA-M3V VITESSE KM13-1S
Page 1
These software drivers can be installed from the CD supplied with each product. If you need to use both products, install both drivers. Markings: KM13-1S is marked with “KM13-1S” KM13-1N is marked with “KM13” IM 34M06C91-01E 6th Edition Yokogawa Electric Corporation...
- Every effort has been made to ensure accuracy in the preparation of this manual. However, should any errors or omissions come to the attention of the user, please contact the nearest Yokogawa Electric representative or sales office. Safety Symbols - Danger.
Page 5
WARRANTY that is provided separately. - Yokogawa Electric assumes no liability to any party for any loss or damage, direct or indirect, caused by the use or any unpredictable defect of the product.
Page 6
Software Supplied by the Company - Yokogawa Electric makes no other warranties expressed or implied except as provided in its warranty clause for software supplied by the company. - Use the software with one computer only. You must purchase another copy of the software for use with each additional computer.
Page 7
General Requirements for Using the FA-M3 / e-RT3 Controller Set the product in a location that fulfills the following requirements: - Where the product will not be exposed to direct sunlight, and where the operating surrounding air temperature is from 0°C to 55°C (32°F to 131°F). There are modules that must be used in an environment where the operating surrounding air temperature is in a range smaller than 0°C to 55°C (32°F to 131°F).
Page 8
Configure for CE Marking Conformance: For compliance to CE Marking, perform installation and cable routing according to the description on compliance to CE Marking in the “Hardware Manual” (IM 34M06C11-01E). The list of CE conforming models is available in Appendix A2. of “Hardware Manual”.
Page 9
- Refer to “A3.5.4 Grounding Procedure” in the “Hardware Manual” for attaching the grounding wiring. Authorized Representative: - The Authorized Representative for this product in the EEA is: Yokogawa Europe B. V. Euroweg 2, 3825 HD Amersfoort, The Netherlands IM 34M06C91-01E...
Page 10
viii General Requirements for Using the FA-M3 Slave Units (TAH Series) C onnect YHLS cable to SHIELD terminal: - Connect the DRAIN line of the YHLS cable to the SHIELD terminal of the YHLS master module securely. Failing to do so may affect the performance of the YHLS system.
Page 11
With reference to the equipment types in the WEEE directive, this product is classified as a “Monitoring and Control instruments”. When disposing of products in the EU, contact your local Yokogawa Europe B. V. office. Do not dispose of this product in domestic household waste.
Introduction Overview of the Manual This manual describes how to install and use the USB-Serial Converter (KM13-1), which is to be connected between the programming port of a sequence CPU module (F3SP) and the USB port of a PC. Read it carefully to ensure correct and safe use of the product.
Copyrights The copyright of the programs and online manuals contained in the software medium of the Software Product shall remain in YOKOGAWA. You are allowed to print the required pages of the online manuals for the purposes of using or operating the Product; however, reprinting or reproducing the entire document is strictly prohibited by the Copyright Law.
TOC-1 FA-M3 USB-Serial Converter IM 34M06C91-01E 6th Edition CONTENTS Applicable Product ..................i Important ....................ii Introduction ....................x Copyrights and Trademarks ..............xi Part A KM13-1S A1. Features ..................A1-1 A2. Specifications ................A2-1 Model and Suffix Codes ..............A2-1 ...
Page 16
TOC-2 Part B KM13-1N B1. Features ..................B1-1 B2. Specifications ................B2-1 Model and Suffix Codes ..............B2-1 Functional Specifications ..............B2-1 Compatible PCs and Operating Systems ........B2-1 External Dimensions ................ B2-1 Precautions When Using KM13-1N ..........B2-2 ...
Page 19
A1- 1 Features This product is a USB-to-RS232C converter compliant to USB specification rev. 1.1. It supports data transmission rate of up to 230 kbps. USB connector allows easy attachment and detachment. By using a virtual COM port, it does not consume IRQ resource of a PC. LED indicator allows easy monitoring of the communications status.
A2-1 Specifications Model and Suffix Codes Suffix Style Option Model Description Code Code Code USB1.1 compliant USB-serial converter cable, KM13 … … Approx. 3 m long Functional Specifications Item Description Input/output signal level RS232C compliant Connection interface USB (Universal Serial Bus) 1.1 compliant Number of I/O ports 1 port 85 mm (L) x 28 mm (W) x 11 mm (H)
A2-2 Precautions When Using KM13-1S WARNING Always discharge any static electricity before touching the product when working in an environment prone to static charge to prevent malfunction due to electrical discharge to the internal circuitry through gaps in the casing. CAUTION This product is a class B information technology equipment based on the Voluntary Control Council for Interference by Information Technology Equipment (VCCI)
A3- 1 Installation A3.1 Connecting the KM13-1S To use this product, you need to perform the following steps: Attach the product to the PC Install the driver software Follow the detailed description given below to perform setup. Attaching to the PC 1.
(2) Open the CD-ROM in Explorer or any other way, and start "Setup.exe". This starts up InstallShield Wizard of the driver software, and the Welcome to the InstallShield Wizard for YOKOGAWA A1045UR Installer dialog box appears. Step (3) (3) Click the [Next] button.
Page 25
A3-3 (5) The InstallShield Wizard Complete dialog box appears. Step (5) (6) Connect the product to the PC. Proceed to Section A3.4 "Verifying Installation in a Windows Vista/7/8/8.1/10 Environment". CAUTION Configuring the FA-M3 and software to use higher transmission rates will allow smoother use.
"Setup.exe". This starts up InstallShield Wizard of the driver software, and the Welcome to the Step (3) InstallShield Wizard for YOKOGAWA A1045UR Installer dialog box appears. (3) Click the [Next] button. The Ready to Install the Program dialog box appears.
Page 27
A3-5 (5) The InstallShield Wizard Complete dialog box appears. Step (5) (6) Connect the product to the PC. Proceed to Section A3.4 "Verifying Installation in a Windows Vista/7/8/8.1/10 Environment". CAUTION Configuring the FA-M3 and software to use higher transmission rates will allow smoother use.
(1) Click [System and Maintenance] in Windows Control Panel. Click [Device Manager] to open the device manager. (2) Under “Ports (COM & LPT)”, select “YOKOGAWA USB Serial Port (COMx)” (‘x’ is a numerical digit denoting the COM port number). Steps (1) and (2) (3) The Properties dialog is displayed.
A3- 7 A3.5 Installing in Windows XP Environment This section describes how to install the driver software required for use in a Windows XP environment. To install the driver software in Windows XP, use the Windows Plug and Play function. Follow the steps below to perform installation.
Page 30
A3- 8 (5) Copying of the driver software begins. When installation is completed, a confirmation screen displayed. Click [Finish]. ⇒ At this point, you have completed installing the driver software. Proceed to Section A3.7, “Verifying Installation in Windows 2000/XP Environment”. CAUTION Step (5) Configuring the FA-M3 and software to...
A3- 9 A3.6 Installing in Windows 2000 Environment This section describes how to install the driver software required for using the product in a Windows 2000 environment. To install the driver software in Windows 2000, use the Windows Plug and Play function. Follow the steps below to perform installation.
Page 32
A3- 10 (4) A screen prompting manufacturer’s installation disk is displayed. Click [Browse] and select the “x:\Win2000” folder on the CD- ROM. “x:\Win2000” is displayed in the [Copy manufacturer’s files from:] field. Click [OK]. (‘x’ denotes the drive letter (e.g. ‘d’) of Step (4) the CD drive containing the product CD-ROM.)
A3- 11 A3.7 Verifying Installation in Windows 2000/XP Environment This section describes how to verify whether the driver software is properly installed for the product. This verification also checks whether the KM13-1S is working correctly on the PC. Operation (1) Double-click [System] in Windows Control Panel to open the System Properties dialog.
A4-1 COM Port Setup For Windows 2000/XP/Vista/7/8/8.1/10 On Windows 2000, Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1, or Windows 10, you can change the COM port allocated to KM13-1S using the device manager. For details on the procedure, see Section A4.1. IM 34M06C91-01E 6th Edition : May 31, 2017-00...
(1) Click [System and Maintenance] in Windows Control Panel. Click [Device Manager] to open the device manager window. (2) Under “Ports (COM & LPT)”, select “YOKOGAWA Serial Port (COMx)” ( ‘x’ is a number). Step (2) (3) The Properties dialog is displayed.
Page 37
A4-3 (5) From [COM Port Number], select the desired port number. This completes COM port setup. Step (5) IM 34M06C91-01E 6th Edition : May 31, 2017-00...
A4-4 A4.1.2 Operation in Windows 2000/XP Procedure ◆ (1) Double-click [System] in Windows Control Panel to open the System Properties dialog. Select [Hardware] tab, and click [Device Manager] to open the device manager window. (2) Under “Ports (COM & LPT)”, select “KM13-1S USB-Serial Converter...
Use the uninstaller supplied with the product to automatically uninstall the driver. (1) Executing the Uninstaller 1. From the Control Panel, select [Programs]-[Uninstall a program]. 2. From the displayed list, select [YOKOGAWA A1045UR Installer] and start the uninstallation. 3. The uninstaller automatically uninstalls the driver from the system.
A5-2 A5.2 For Windows 2000/XP To uninstall the driver, you need to (1) delete the associated device information; and (2) delete the associated inf file. (1) Deleting Device Information 1. With the KM13-1S inserted in the USB port, double-click [System] on Windows control panel.
Index A FA-M3 USB-Serial Converter Part A KM13-1S IM 34M06C91-01E 6th Edition Index transmission distance ........A2-1 transmission speed ........... A2-1 attaching to the PC ........... A3-1 uninstalling the driver ........A5-1 COM port setup ..........A4-1 communications parameters ......A2-1 weight ...............
B1- 1 Features This product is a USB-to-RS232C converter compliant to USB specification rev. 1.1. It supports data transmission rate of up to 230 kbps. USB connector allows easy attachment and detachment. By using a virtual COM port, it does not consume IRQ resource of a PC. LED indicator allows easy monitoring of the communications status.
B2- 1 Specifications Model and Suffix Codes Suffix Style Option Model Description Code Code Code USB1.1 compliant USB-serial converter cable, KM13 … … Approx. 3 m long Functional Specifications Item Description Input/output signal level RS232C compliant Connection interface USB (Universal Serial Bus) 1.1 compliant Number of I/O ports 1 port 85 mm (L) x 28 mm (W) x 11 mm (H)
B2- 2 Precautions When Using KM13-1N Always discharge any static electricity before touching the product when working in an environment prone to static charge to prevent malfunction due to electrical discharge to the internal circuitry through gaps in the casing. CAUTION This product is a class B information technology equipment based on the Voluntary Control Council for Interference by Information Technology Equipment (VCCI)
B3- 1 Installation B3.1 Connecting the KM13-1N To use this product, you need to perform the following steps: Attach the product to the PC Install the driver software Follow the detailed description given below to perform setup. Attaching to the PC 1.
B3- 2 B3.2 Installing in Windows 2000 Environment This section describes how to install the driver software required for using the product in a Windows 2000 environment. Follow the steps below to perform installation. Procedure (1) Connect the product to the PC. This automatically starts up the “Found New Hardware Wizard”.
Page 51
B3- 3 (5) The Driver Files Search Results screen displayed. Verify that “x:\KM13-1N\win2000\serwpl.inf” displayed on the screen and click [Next]. (‘x’ denotes the drive letter (e.g. ‘D’) for the CD drive containing the product CD-ROM) (6) Copying of the driver software begins. When installation is completed, a confirmation screen...
B3- 4 B3.3 Installing in Windows XP Environment This section describes how to install the driver software required for use in a Windows XP environment. Follow the steps below to perform installation. Procedure (1) Connect the product to the PC. This automatically starts up the “Found New Hardware Wizard”.
B3- 5 B3.4 Verifying Installation in Windows 2000/XP Environment This section describes how to verify whether the driver software is properly installed for the product. This verification also checks whether the KM13-1N is working correctly on the PC. Operation (1) Double-click [System] in Windows Control Panel to open the System Properties dialog.
B4- 1 COM Port Setup For Windows 2000/XP On Windows 2000 or Windows XP, you can change the COM port allocated to KM13-1N using the device manager. For details on the procedure, see Section B4.1. IM 34M06C91-01E 5th Edition : Dec. 25, 2013- 00...
B4- 2 B4.1 COM Port Setup Using Device Manager This section describes how to change the COM port allocated to KM13-1N using Device Manager on Windows XP or 2000. Procedure (1) Double-click [System] in Windows Control Panel to open the System Properties dialog.
B5- 1 Uninstalling the Driver This chapter describes how to remove the software driver for the product. For Windows 2000/ / / / XP B5.1 To uninstall the driver, you need to (1) delete the associated device information; and (2) delete the associated inf file.
Index B FA-M3 USB-Serial Converter Part B KM13-1N IM 34M06C91-01E 6th Edition Index uninstalling the driver ........B5-1 attaching to the PC ........... B3-1 weight ............... B2-1 COM port setup ..........B4-1 communications parameters ......B2-1 communications protocol ........B2-1 compatible operating systems ......
■For Questions and More Information If you have any questions, you can send an E-mail to the following address. plc_message@csv.yokogawa.co.jp E-mail: ■Written by Yokogawa Electric Corporation ■Published by Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo, 180-8750, JAPAN IM 34M06C91-01E 6th Edition : May. 31, 2017-00...