Safety Notes; Operating Elements And Connections - Monacor img Stage Line LED-810DMX Instruction Manual

All operating elements and connections can be
GB
found on the fold-out page 3.

1 Operating Elements and Connections

1.1 Light effect unit LED-810DMX /-812DMX
1 Mounting bracket
2 DIP switches Nos. 1 – 9 for adjusting the address of
the unit or the operating mode (master or slave
mode); DIP switch No. 10 for defining the behav-
iour in the slave mode (
3 Indicating LED
– if it is permanently on:
no DMX or music control
– if it is extinguished to the beat of the music:
music control via the microphone (4)
– if it keeps flashing:
control via a DMX light controller
4 Microphone for music control
5 Connection jack for the remote control LC-3
6 Locking screws for the mounting bracket (1)
7 DMX signal input (3-pole XLR) for connecting a
light controller;
Pin 1 = ground, 2 = DMX-, 3 = DMX+
8 DMX signal output (3-pole XLR) for connection to
the DMX input of another DMX light effect unit;
Pin 1 = ground, 2 = DMX-, 3 = DMX+
9 Support for the mains fuse
Always replace a fuse that has blown by one of the
same type.
10 Mains jack for connection to a socket (230 V~ / 50
Hz) via the mains cable provided
1.2 Remote control LC-3
The remote control is available as an accessory and
not supplied with the light effect unit.
11 Button STAND BY for deactivating the light beam
12 Button FUNCTION for selecting various functions
depending on the operating mode selected with the
button MODE (13)
13 Button MODE for switching over between
Stroboscope mode (LED of the button off)
Chase mode
Note: For control via the remote control, there must be no
DMX signal at the DMX INPUT (7).
8
chapter 6.2)
(LED of the button on)

2 Safety Notes

The unit corresponds to all required directives of the
EU and is therefore marked with
WARNING The unit uses dangerous mains voltage
(230 V~). Leave servicing to skilled per-
sonnel only and do not insert anything
into the air vents; inexpert handling may
result in electric shock.
Please observe the following items in any case:
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
G
Do not operate the unit or immediately disconnect
the mains plug from the mains socket
1. if the unit or the mains cable is visibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled per-
sonnel.
G
Never pull the mains cable for disconnecting the
mains plug from the mains socket, always seize the
plug.
G
For cleaning only use a dry, soft cloth, never use
chemicals or water.
G
No guarantee claims for the unit and no liability for any
resulting personal damage or material damage will be
accepted if the unit is used for other purposes than
originally intended, if it is not safely mounted or cor-
rectly operated, or if it is not repaired in an expert way.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in accord -
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
.
,