Download
Share
Print this page
SunSetter OASIS Replacement Instructions Manual
  1. Manuals
  2. Brands
  3. SunSetter Manuals
  4. Accessories
  5. Oasis
  6. Replacement instructions manual
SunSetter OASIS Replacement Instructions Manual

SunSetter OASIS Replacement Instructions Manual

Awning fabric
Hide thumbs Also See for OASIS:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
OASIS Awning Fabric Replacement Instructions
Tools Needed: Phillips Screwdriver, Small Flat Blade Screwdriver, Scissors, Hammer, Measuring Tape,
Sawhorses or chairs.
Parts Supplied: Replacement Fabric, (4) Plastic safety sleeves, (4) Plastic Front Bar Inserts.
CAUTION: DO NOT REMOVE THE REPLACEMENT FABRIC FROM THE PROTECTIVE PLASTIC SLEEVE
UNTIL TOLD TO DO SO. THE FABRIC HAS BEEN PRE-ROLLED TO FACILITATE PROPER ALIGNMENT AND
INSTALLATION INTO THE FRONT BARS AND ROLLER BAR.
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!!
PLEASE READ THESE INSTRUCTIONS ENTIRELY BEFORE ATTEMPTING THIS PROCEDURE.
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU FACE THE GEAR ASSEMBLY OR MOTOR.
1. Make sure that the awning is completely closed, and remove the crank wand from the gear
assembly. Note: For motorized models unplug the power cord from your electrical outlet.
2. Position two saw horses or chairs approximately eight (8) feet apart.
WARNING: THE FOLLOWING PROCEDURE SHOULD BE ACCOMPLISHED BY FOUR PEOPLE.
3. One person should be positioned at each leg assembly to prevent the awning from sliding as the
unit is carefully tipped over. See Figure 1 inset for the four (4) person positions.
4. One person should be positioned at each end of the awning assembly, and be able to lift and
support the weight of that end of the awning.
Note: Before you tip the awning over, make sure that the crank loop on the Gear Assembly or the
Override crank loop on the Motorized model will be on the top of the awning.
©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148
RETRACTABLE AWNINGS
For Technical Support visit us at www.sunsetter.com/ownerscorner
or Call Toll Free 800-670-7071 • Fax 877-224-4944
"Four or More Helpers Needed"

Advertisement

loading

Related Manuals for SunSetter OASIS

Summary of Contents for SunSetter OASIS

  • Page 1 Note: Before you tip the awning over, make sure that the crank loop on the Gear Assembly or the Override crank loop on the Motorized model will be on the top of the awning. ©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148...
  • Page 2 Note: Waist height is a good working height for replacing the OASIS fabric. WARNING: PLEASE HAVE FOUR HELPERS HOLD THE OASIS IN PLACE TO PREVENT INJURY TO PEOPLE AND PREVENT DAMAGE TO THE OASIS WHILE PERFORMING THIS PROCEDURE. Figure 1 Note: The Awning should be positioned at approximately waist height for the following steps.
  • Page 3 7. Orient the awning assembly on the saw horses or chairs, so that the Square Bar Uprights are resting on the saw horses or chairs. See Figure 1. Note: During the following step, your helpers will need to guide the fabric so that it doesn’t wrap around the roller bar as you unroll the fabric.
  • Page 4 11. Using a small flat blade screwdriver, carefully remove the Plastic Inserts from the Fabric Slot and Valance Slot of both Front Bars. See Figure 5. Front Bar Plastic Inserts Valance Figure 5 12. NOTE THE ORIENTATION OF THE FABRIC: The hemmed (folded) edges on the sides of the fabric should be facing down.
  • Page 5 Assembly should carefully lift the Awning together and tip the unit until the Awning is upright on the Leg Assemblies. 29. Manual Models: Using the Hand Crank, unroll the OASIS Awning. The Arms will still be bent at the elbow, this is normal as they will never straighten out completely.
  • Page 6 Side view of the White Protective Cap to View and Yellow Push Buttons the Push Buttons for Setting the Open and Closed Limits OASIS Top view of the Fabric White and Yellow Limit Push Buttons for Setting the Open and Closed Limits...
  • Page 7 APPENDIX B Resetting Remote Communication and Reprogramming the Motor • This procedure describes the actions needed to reset the communication between the Motor and the primary Remote Transmitter used to control your Motorized Awning. • This procedure programs the Awning Motor to accept commands from one primary Remote Transmitter. •...
  • Page 8 • On the additional Control Device, press the Programming button until the motor “jogs,” then release To DELETE a Control Device, repeat the two steps listed above and the additional Control Device is removed. SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148 January 30, 2015 Oasis_Fabric_Replacement...